| Age | Commit message (Collapse) | Author |
|---|
|
Instead of open-coded version.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While looking at UDP port randomization, I noticed it
was litle bit pessimistic, not looking at type of sockets
(IPV6/IPV4) and not looking at bound addresses if any.
We should perform same tests than when binding to a
specific port.
This permits a cleanup of udp_lib_get_port()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
$ codiff tcp_ipv6.o.old tcp_ipv6.o.new
net/ipv6/tcp_ipv6.c:
tcp_v6_md5_hash_hdr | -144
tcp_v6_send_ack | -585
tcp_v6_send_reset | -540
3 functions changed, 1269 bytes removed, diff: -1269
net/ipv6/tcp_ipv6.c:
tcp_v6_send_response | +791
1 function changed, 791 bytes added, diff: +791
tcp_ipv6.o.new:
4 functions changed, 791 bytes added, 1269 bytes removed, diff: -478
I choose to leave the reset related netns comment in place (not
the one that is killed) as I cannot understand its English so
it's a bit hard for me to evaluate its usefulness :-).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
after this I get:
$ diff-funcs tcp_v6_send_reset tcp_ipv6.c tcp_ipv6.c tcp_v6_send_ack
--- tcp_ipv6.c:tcp_v6_send_reset()
+++ tcp_ipv6.c:tcp_v6_send_ack()
@@ -1,4 +1,5 @@
-static void tcp_v6_send_reset(struct sock *sk, struct sk_buff *skb)
+static void tcp_v6_send_ack(struct sk_buff *skb, u32 seq, u32 ack, u32 win,
u32 ts,
+ struct tcp_md5sig_key *key)
{
struct tcphdr *th = tcp_hdr(skb), *t1;
struct sk_buff *buff;
@@ -7,31 +8,14 @@
struct sock *ctl_sk = net->ipv6.tcp_sk;
unsigned int tot_len = sizeof(struct tcphdr);
__be32 *topt;
-#ifdef CONFIG_TCP_MD5SIG
- struct tcp_md5sig_key *key;
-#endif
-
- if (th->rst)
- return;
-
- if (!ipv6_unicast_destination(skb))
- return;
+ if (ts)
+ tot_len += TCPOLEN_TSTAMP_ALIGNED;
#ifdef CONFIG_TCP_MD5SIG
- if (sk)
- key = tcp_v6_md5_do_lookup(sk, &ipv6_hdr(skb)->daddr);
- else
- key = NULL;
-
if (key)
tot_len += TCPOLEN_MD5SIG_ALIGNED;
#endif
- /*
- * We need to grab some memory, and put together an RST,
- * and then put it into the queue to be sent.
- */
-
buff = alloc_skb(MAX_HEADER + sizeof(struct ipv6hdr) + tot_len,
GFP_ATOMIC);
if (buff == NULL)
@@ -46,18 +30,20 @@
t1->dest = th->source;
t1->source = th->dest;
t1->doff = tot_len / 4;
- t1->rst = 1;
-
- if(th->ack) {
- t1->seq = th->ack_seq;
- } else {
- t1->ack = 1;
- t1->ack_seq = htonl(ntohl(th->seq) + th->syn + th->fin
- + skb->len - (th->doff<<2));
- }
+ t1->seq = htonl(seq);
+ t1->ack_seq = htonl(ack);
+ t1->ack = 1;
+ t1->window = htons(win);
topt = (__be32 *)(t1 + 1);
+ if (ts) {
+ *topt++ = htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) |
+ (TCPOPT_TIMESTAMP << 8) |
TCPOLEN_TIMESTAMP);
+ *topt++ = htonl(tcp_time_stamp);
+ *topt++ = htonl(ts);
+ }
+
#ifdef CONFIG_TCP_MD5SIG
if (key) {
*topt++ = htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) |
@@ -84,15 +70,10 @@
fl.fl_ip_sport = t1->source;
security_skb_classify_flow(skb, &fl);
- /* Pass a socket to ip6_dst_lookup either it is for RST
- * Underlying function will use this to retrieve the network
- * namespace
- */
if (!ip6_dst_lookup(ctl_sk, &buff->dst, &fl)) {
if (xfrm_lookup(&buff->dst, &fl, NULL, 0) >= 0) {
ip6_xmit(ctl_sk, buff, &fl, NULL, 0);
TCP_INC_STATS_BH(net, TCP_MIB_OUTSEGS);
- TCP_INC_STATS_BH(net, TCP_MIB_OUTRSTS);
return;
}
}
...which starts to be trivial to combine.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maybe it's just me but I guess those md5 people made a mess
out of it by having *_md5_hash_* to use daddr, saddr order
instead of the one that is natural (and equal to what csum
functions use). For the segment were sending, the original
addresses are reversed so buff's saddr == skb's daddr and
vice-versa.
Maybe I can finally proceed with unification of some code
after fixing it first... :-)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl8169_init_one
-> rtl_init_mac_address
-> rtl_rar_set
-> spin_lock_irq(&tp->lock);
[...]
-> spin_lock_init(&tp->lock);
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix warnings caught by David Miller on sparc64
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The T5 timer is the timer for the over-all shutdown procedure. If
this timer expires, then shutdown procedure has not completed and we
ABORT the association. We should update SCTP_MIB_ABORTED and
SCTP_MIB_CURRESTAB when aborting.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If ABORT chunks require authentication and a protocol violation
is triggered, we do not tear down the association. Subsequently,
we should not increment SCTP_MIB_ABORTED.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC3873 defined SCTP_MIB_CURRESTAB:
sctpCurrEstab OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of associations for which the current state is
either ESTABLISHED, SHUTDOWN-RECEIVED or SHUTDOWN-PENDING."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
If the T4 RTO timer expires many times(timeout), the association will enter
CLOSED state, so we should dec the number of SCTP_MIB_CURRESTAB, not inc the
number of SCTP_MIB_CURRESTAB.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to modulus the queue number in ->hard_start_xmit() since the
core is going to do that for you modulus ->real_num_tx_queues.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
same patch as e1000e
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before, the driver would not care about the return codes from pci_map_*
functions. This could be potentially dangerous if a mapping failed.
Now, we will check all pci_map_* calls. On the transmit side, we switch
to use the new function skb_dma_map(). On the receive side, we add
pci_dma_mapping_error().
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is now possible with updated firmware.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this new firmware, the driver no longer has to modify the
TCP/IP header fields when transmitting TSO packets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to check netif_running() state in most ethtool operations
and properly handle the !netif_running() state where the chip is
in an uninitailzed state or low power state that may not accept
any MMIO.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This logic is used in bnx2_close() and bnx2_suspend() and
so should be separated out into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes the RX/TX byte counters for IPIP, GRE and SIT more
consistent. Previously we included the external IP headers on the
way out but not when the packet is inbound.
The new scheme is to count payload only in both directions. For
IPIP and SIT this simply means the exclusion of the external IP
header. For GRE this means that we exclude the GRE header as
well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for Ethernet over GRE encapsulation.
This is exposed to user-space with a new link type of "gretap"
instead of "gre". It will create an ARPHRD_ETHER device in
lieu of the usual ARPHRD_IPGRE.
Note that to preserver backwards compatibility all Transparent
Ethernet Bridging packets are passed to an ARPHRD_IPGRE tunnel
if its key matches and there is no ARPHRD_ETHER device whose
key matches more closely.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a netlink interface that will eventually displace
the existing ioctl interface. It utilises the elegant rtnl_link_ops
mechanism.
This also means that user-space no longer needs to rely on the
tunnel interface being of type GRE to identify GRE tunnels. The
identification can now occur using rtnl_link_ops.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the dev->mtu setting out of ipgre_tunnel_bind_dev.
This is in prepartion of using rtnl_link where we'll need to make
the MTU setting conditional on whether the user has supplied an
MTU. This also requires the move of the ipgre_tunnel_bind_dev
call out of the dev->init function so that we can access the user
parameters later.
This patch also adds a check to prevent setting the MTU below
the minimum of 68.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have dev->needed_headroom, we can use it instead of
having a bogus dev->hard_header_len. This also allows us to
include dev->hard_header_len in the MTU computation so that when
we do have a meaningful hard_harder_len in future it is included
automatically in figuring out the MTU.
Incidentally, this fixes a bug where we ignored the needed_headroom
field of the underlying device in calculating our own hard_header_len.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/jme.c:1598: warning: ‘jme_set_100m_half’ defined but not used
drivers/net/jme.c:1618: warning: ‘jme_wait_link’ defined but not used
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advances the driver version after modification.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix IRQ handle bug when interrupt mode.
The driver was incorrectly handled and returned IRQ_HANDLED
while the device is not generating the interrupt.
It happened due to faulty determination of interrupt status register.
Found by: "Ethan" <ethanhsiao@jmicron.com>
Fixed by: "akeemting" <akeem@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Set bit 5 of GPREG1 to 1 to enable hardware workaround for half-duplex
mode. Which the MAC processor generates CRS/COL by itself instead of
receive it from PHY processor.
2. Set bit 6 of GPREG1 to 1 to enable hardware workaround that masks the
MAC processor working right while calculating IPv6 RSS in 10/100
mode.
3. Group the workaround codes all together.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 1G optical Vitesse PHY.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for SR PHY.
Auto-detect phy module type, and report type changes.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add generic code to manage interrupt driven PHYs.
Do not reset the phy after link parameters update,
the new values might get lost.
Return early from link change notification
when the link parameters remain unchanged.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not require PHY interrupts to be connected to GPIs in ascending order.
Base interrupt availability both on PHYs supporting them and on GPIs being
hooked up. Allows boards to specify interrupt GPIs though the PHYs don't
use them.
Remove spurious PHY interrupts due to clearing T3DBG interrupts before
setting their polarity.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Second step in overall phy layer reorganization.
Clean up the port_type_info structure.
Support coextistence of clause 22 and clause 45 MDIO devices.
Select the type of MDIO transaction on a per transaction basis.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
First step towards overall PHY layering re-organization.
Allow a status return when a PHY is reset.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate a queue set per core, up to the maximum of available qsets.
Share the queue sets on multi port adapters.
Rename MSI-X interrupt vectors ethX-N, N being the queue set number.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when a fatal error occurs, bring ports down, reset the chip,
and bring ports back up.
Factorize code used for both EEH and fatal error recovery.
Fix timer usage when bringing up/resetting sge queue sets.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell 88E6060 switch chip. This chip only
supports the Header and Trailer tagging formats, and we use it in
Trailer mode since that mode is slightly easier to handle than
Header mode.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Trailer switch tagging format. This is
another tagging that doesn't explicitly mark tagged packets with a
distinct ethertype, so that we need to add a similar hack in the
receive path as for the Original DSA tagging format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell 88E6131 switch chip. This chip only
supports the original (ethertype-less) DSA tagging format.
On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive
access to each of the PHYs's MII management registers. If we want to
talk to the PHYs from software, we have to disable the PPU and wait
for it to complete its current transaction before we can do so, and we
need to re-enable the PPU afterwards to make sure that the switch will
notice changes in link state and speed on the individual ports as they
occur.
Since disabling the PPU is rather slow, and since MII management
accesses are typically done in bursts, this patch keeps the PPU disabled
for 10ms after a software access completes. This makes handling the
PPU slightly more complex, but speeds up something like running ethtool
on one of the switch slave interfaces from ~300ms to ~30ms on typical
hardware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the DSA switches currently in the field do not support the
Ethertype DSA tagging format that one of the previous patches added
support for, but only the original DSA tagging format.
The original DSA tagging format carries the same information as the
Ethertype DSA tagging format, but with the difference that it does not
have an ethertype field. In other words, when receiving a packet that
is tagged with an original DSA tag, there is no way of telling in
eth_type_trans() that this packet is in fact a DSA-tagged packet.
This patch adds a hook into eth_type_trans() which is only compiled in
if support for a switch chip that doesn't support Ethertype DSA is
selected, and which checks whether there is a DSA switch driver
instance attached to this network device which uses the old tag format.
If so, it sets the protocol field to ETH_P_DSA without looking at the
packet, so that the packet ends up in the right place.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The write barrier should be used before starting a DMA transfer. This fixes
a problem, where almost all packets received on another machine had garbled
content. Tested with an RTL8100C on a MIPS machine.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
there's several drivers that have use "tx_timeout" for the .. tx
timeout function. All fine with that, they're static, however for
doing stats on how often which driver hits the timeout it's a tad
unfortunate. The patch below gives the ones I found in the
kerneloops.org database unique names.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building with CONFIG_USB_DEBUG, don't create logspam from
the USB networking drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since recent kernel (2.6.26 or 2.6.27) the PCI wakeup functions are
influenced by generic device ability and configuration when enabling
PCI-device triggered wake-up.
This patch causes WoL setting to enable/disable device's wish to
be permitted to wake-up the host when changing WoL options and
also during device probing.
Without this patch one has write 'enabled' to
/sys/bus/pci/devices/0000:02:08.0/power/wakeup
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When probing the chip and handling it's power management settings
also remember wether WoL feature is enabled.
Without this patch one has to call ethtool to change WoL settings
for this flag to be set and any WoL being enabled on suspend to
RAM.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device's carrier status is controlled via the functions
netif_carrier_on() and netif_carrier_off(). These set or clear a bit
indicating the carrier (aka lower level link) is down, and if the state
changed, they fire off a routing netlink event.
Add a call to netif_carrier_off() before register_netdev() so that the
newly created device will be set to carrier down. Then when the carrier
comes up for the first time, a netlink event will be generated, as the
carrier changed from down to up. Otherwise the initial carrier up will
appear to be changing the status from up to up, and so no event is
generated since that's not a change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
