| Age | Commit message (Collapse) | Author |
|---|
|
The previous version used a simple loop to go through all Beacon
frames when determining the next TBTT and DTIM count. This is not too
bad for the case where the setup happens before timesync (i.e., very
small TSF), but this can become very heavy operation if a short Beacon
interval is used and the current TSF is large.
In preparation for a patch to update timer setup based on Beacon
timestamp, optimize this routine to take fixed time regardless of the
actual TSF value.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.
When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).
This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688: IF_SDIO_SCRATCH (0x34/0x35)
Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN 0x42 is read every time when rx interrupt is received.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in. This
can lead, for example, to the card failing to re-associate. This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In "mac80211: split out and decrease probe wait time" I tried
to reduce the time waiting for a probe response, but failed to
take into account the case where we are detecting beacon loss
in software -- in that case we still wait the monitoring time
rather than the probe wait time. Fix this by refactoring the
mod_timer() calls in ieee80211_associated().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The requirement for wireless stats to be atomic is now mostly
artificial since we hold the rtnl _and_ the dev_base_lock for
iterating the device list. Doing that is not required, just the
rtnl is sufficient (and the rtnl is required for other reasons
outlined in commit "wext: fix get_wireless_stats locking").
This will fix http://bugzilla.kernel.org/show_bug.cgi?id=13344
and make things easier for drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, we will ask the driver to configure right away
when somebody changes the desired BSSID. That's totally
strange because then we will configure the driver without
even knowing whether the BSS exists. Change this to only
configure the BSSID when associated, and configure a zero
BSSID when not associated.
As a side effect, this fixes an issue with the iwlwifi
driver which doesn't implement sta_notify properly and
uses the BSSID instead and gets very confused if the
BSSID is cleared before we disassociate, which results
in the warning Marcel posted [1] and iwlwifi bug 1995 [2].
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/32598
[2] http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1995
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Device drivers using wiphy_apply_custom_regulatory() want some
regulatory settings applied to their wiphy, if no bands were
configured on the wiphy then something went wrong.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is always discarded anyway but lets just set this to our
safest lowest.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When I fixed the crypto bit I must have done the negative
test only -- it is quite clearly impossible to find _any_
IBSS to join with the parameters put the wrong way around.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath_regd_init() needs to be called with the wiphy already
properly set with the bands. Without this the custom regulatory
settings were not taking effect, and the device would get
the default channel settings from ath9k_[25]ghz_chantable.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the genIE hasn't changed there's no reason to kick
the state machine since it won't be able to do anything
new -- doing this decreases the useless work we do for
reassociating because if we do kick the state machine
it will try to find a usable BSS but there might not be
one because wpa_supplicant will only change the BSSID
a little later.
In a sense this is a workaround for userspace behaviour,
but on the other hand userspace cannot really keep track
of what the kernel currently has for genIE since any
process could have changed that while wpa_supplicant
wasn't looking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Report status unknown as if there were successfully transmitted.
This will avoid hostapd to disassociate because it doesn't understand what a status unknown is.
Signed-off-by: Alexandre Becholey <alexandre.becholey@epfl.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When updating the duration field for TX frames, skip the update for
PS-Poll frames that use this field for other purposes (AID).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the AP includes our AID in the TIM IE, we need to process the
Beacon frame as far as PS is concerned (send PS-Poll or nullfunc data
with PM=0). The previous code skipped this in cases where the CRC
value did not change and it would not change if the AP continues
including our AID in the TIM..
There is no need to count the crc32 value for directed_tim with this
change, so we can remove that part. In order not to change the order
of operations (i.e., update WMM parameters prior to sending PS-Poll),
the CRC match is checked twice as only after the PS processing step,
the rest of the function is skipped if nothing changed in the Beacon.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 does not set PM field for normal data frames, so we need to
update that based on the current PS mode when using PS-Poll
(timeout=0) power save mode.
This allows the AP to remain in sync with our PS state. However, there
is still a potential race condition between PS state changes when
multiple TX queues are used and nullfunc and PS-Poll frames use
different queue. That corner case may need to be handled separately by
changing which queue is used either in ath9k or mac80211.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We must make sure the chip is awake when changing the RX filter
parameters. This could have caused problems, e.g., when changing the
interface to promiscuous mode while in sleep mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the chip complains about TSF sync, make sure we remain awake to
sync with the next Beacon frame. In theory, this should not be needed
since we are currently trying to receive all Beacon frames, anyway,
better have this code ready should we ever change that.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the chip is in sleep mode, there is no point trying to calibrate
the radio since it will just results in incorrect values being read
from registers and other potential issues. In addition, if we actually
start processing calibrate, do not allow the chip to be put into sleep
until we have completed the calibration step.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When using timeout=0 (PS-Poll) with mac80211, the driver will need to
wake up for TX requests and remain awake until the TX has been
completed (ACK received or timeout) or until the buffer frame(s) have
been received (in case the TX is for a PS-Poll frame).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Moving information from config_interface to bss_info_changed
removed struct ieee80211_if_conf which the documentation still
refers to, additionally there's one kernel-doc description too
much and one other missing, fix all this.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If CONFIG_CFG80211_DEBUGFS is enabled and CONFIG_MAC80211_DEBUGFS is
not, compilation fails in net/wireless/debugfs.c:
net/wireless/debugfs.c: In function 'cfg80211_debugfs_drv_add':
net/wireless/debugfs.c:117: error: 'struct cfg80211_registered_device'
has no member named 'debugfs'
The debugfs filed is needed if and only if CONFIG_CFG80211_DEBUGFS is
enabled, so use that instead of CONFIG_MAC80211_DEBUGFS.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If we are trying to interpolate a curve with slope == 0, the return
value will always be the y-coordinate. In this code we are looping
until we reach a minimum y-coordinate on a line, which in the 0-slope
case can never happen, thus the loop never terminates.
The PCDAC steps come from the EEPROM and should never be equal, but
we should gracefully handle that case, so warn and bail out.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is a race on access to last_request and its alpha2
through reg_is_valid_request() and us possibly processing
first another regulatory request on another CPU. We avoid
this improbably race by locking with the cfg80211_mutex as
we should have done in the first place. While at it add
the assert on locking on reg_is_valid_request().
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This has no functional change, but it will make the race
fix easier to spot in my next patch.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This has no functional change except we save a kfree(rd) and
allows us to clean this code up a bit after this. We do
avoid an unnecessary kfree(NULL) but calling that was OK too.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fix to set dev->broadcast correctly, since
dev->broadcast is defined as:
unsigned char broadcast[MAX_ADDR_LEN];
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix this build error:
drivers/staging/agnx/pci.c: In function 'agnx_config_interface':
drivers/staging/agnx/pci.c:315: error: dereferencing pointer to incomplete type
..
drivers/staging/agnx/pci.c:424: error: unknown field 'config_interface' specified in initializer
config_interface was removed in 2d0ddec5b2b
("mac80211: unify config_interface and bss_info_changed")
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We do not need to do this in ath_isr() and it looks like the modified
version ends up being more stable as far as being able receive beacon
frames is concerned. Furthermore, this reduces need to move between
AWAKE and NETWORK SLEEP states when processing some unrelated
interrupts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some applications using wireless extensions expect to be able to
remove a key that doesn't exist. One example is wpa_supplicant
which doesn't actually change behaviour when running into an
error while trying to do that, but it prints an error message
which users interpret as wpa_supplicant having problems.
The safe thing to do is not change the behaviour of wireless
extensions any more, so when the driver reports -ENOENT let
the wext bridge code return success to userspace. To guarantee
this, also document that drivers should return -ENOENT when the
key doesn't exist.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently all radios receive all traffic on the simulated air
if they are tuned to the same channel. This patch introduces
the concept of grouping, which allows to assign a radio to
certain group. Only radios in the same group can 'see' each other.
Each bit in /debug/ieee80211/phy*/hwsim/group
represents one group. By default all radios belong to the same group "1",
e.g. bit 1 is set. Additionally a radio can belong to several groups.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath5k only generated the beacon when bss_info_changed() was called,
but for AP mode this is not enough, because the TIM IE would never
get updated and consequently PS mode clients wouldn't know about
buffered frames. Instead, get a new beacon on every SWBA interrupt.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Drop test for FW_STATE_RESET in p54spi_work as fw_state
is never assigned this value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Process beacon change even if the BSSID doesn't
change at the same time. Also fix what I think
is a small locking error in b43legacy, there's
a spin_unlock_irqrestore that looks out of place.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Under high load first data word, read after available data size
is sometimes lost in p54spi_rx. It seems to depend on frequency
of interrupts and latency of data read request relatively to
'data available' interrupt. The worst consequence of this bug
is loss of packet transmission acknowledgement, which in turn
causes overflow of tx queues and permanent link loss.
Read data size and first data word in one SPI transaction.
No packets from LMAC should have length less than 1 word,
so this shouldn't interfere with the next read transaction.
Also call p54spi_sleep if p54spi_wake succeeded.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Put chip into sleep state, once it's been awaken.
Also, propagate error code to the caller.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Return whether wakeup operation succeeded.
Make use of this return value.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
interrupt status read
When SPI write of odd length is requested, p54spi_write splits it
into two parts: one for all data, except the last byte, and one
for last byte and padding byte. Unfortunately, the length of
first part is not amended. It works because all meaningful bytes
have proper value and the last byte of odd length SPI write
transaction is ignored.
p54spi_work has dummy HOST_INTERRUPTS register read at the end.
Drop it, as its result is not used and it has no side effects.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Host is not allowed to modify DMA_WRITE_CTRL register
if bit HOST_ALLOWED in it is not set. Wait for HOST_ALLOWED first.
Also get rid of timeout in p54spi_wait_bit as it's been playing
a role of workaround for such an incorrect register access.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Eliminate direct accesses to the driver_data field.
cf 82ab13b26f15f49be45f15ccc96bfa0b81dfd015
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device *dev;
expression E;
type T;
@@
- dev->driver_data = (T)E
+ dev_set_drvdata(dev, E)
@@
struct device *dev;
type T;
@@
- (T)dev->driver_data
+ dev_get_drvdata(dev)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows drivers to use a const pointer as the privid without a cast.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows drivers to mark their cfg80211_ops tables const.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch is one of the incremental steps for unifying iwl_station_entry
for all HWs, i.e. removing of iwl3945_station_entry
This patch drops iwl3945_tid_data and use iwl_tid_data instead.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch replaces struct iwl3945_hw_key by struct iwl_hw_key.
It's not used directly with any host command therefore removal is trivial
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This removes unnecessary MMIO accesses in the interrupt hotpath. The
patch by Michael Buesch for b43 has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch configures the beacon timers with beacon interval
and beacon period passed through vif.bss_conf. Also cache the
currecnt beacon configuration which will be used to configure
the beacon timers when the driver triggers it after reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
