| Age | Commit message (Collapse) | Author |
|---|
|
Now swiotlb_pci_dma_ops is identical to swiotlb_dma_ops; we can use
swiotlb_dma_ops with any devices. This removes swiotlb_pci_dma_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch adds max_direct_dma_addr to struct dev_archdata to remove
addr_needs_map in struct dma_mapping_ops. It also converts
dma_capable() to use max_direct_dma_addr.
max_direct_dma_addr is initialized in pci_dma_dev_setup_swiotlb(),
called via ppc_md.pci_dma_dev_setup hook.
For further information:
http://marc.info/?t=124719060200001&r=1&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
|
|
Time time taken for a single cpu online operation on a pseries machine
is as follows:
Dedicated LPAR (POWER6): ~220ms.
Shared LPAR (POWER5) : ~240ms.
Of this time, approximately 200ms is taken up by __cpu_up(). This is because
we poll every 200ms to check if the new cpu has notified it's presence
through the cpu_callin_map. We repeat this operation until the new cpu sets
the value in cpu_callin_map or 5 seconds elapse, whichever comes earlier.
However, using completion_structs instead of polling loops,
the time taken by the new processor to indicate it's presence has
found to be less than 1ms on pseries. This method however may not
work on all powerpc platforms due to the time-base synchronization code.
Keeping this in mind, we could reduce msleep polling interval from
200ms to 1ms while retaining the 5 second timeout.
With this, the time taken for a cpu online operation changes as follows:
Dedicated LPAR (POWER6): 20-25ms.
Shared LPAR (POWER5) : 60-80ms.
In both these cases, it was found that the code polls through the loop
only once indicating that 1ms is a reasonable value, atleast on pseries.
The code needs testing on other powerpc platforms.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On Thu, Aug 13, 2009 at 04:14:58PM +1000, Benjamin Herrenschmidt wrote:
> On Tue, 2009-08-11 at 11:39 +0200, Bastian Blank wrote:
> > This patch just disables this driver on SMP kernels, as it is obviously
> > not supported.
> Why not remove the #error instead ? :-) I don't think it's still
> meaningful, especially since we use the timebase for delays nowadays
> which doesn't depend on the CPU frequency...
Your call. Take this one:
The build of a PowerMac 32bit kernel currently fails with
error: #warning "WARNING, CPUFREQ not recommended on SMP kernels"
Thie patch removes the not longer applicable SMP warning from the
PowerMac cpufreq code.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The ptrace POKETEXT interface allows a process to modify the text pages of
a child process being ptraced, usually to insert breakpoints via trap
instructions. The kernel eventually calls copy_to_user_page, which in turn
calls __flush_icache_range to invalidate the icache lines for the child
process.
However, this function does not work on 44x due to the icache being virtually
indexed. This was noticed by a breakpoint being triggered after it had been
cleared by ltrace on a 440EPx board. The convenient solution is to do a
flash invalidate of the icache in the __flush_icache_range function.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This is an attempt at cleaning up a bit the way we handle execute
permission on powerpc. _PAGE_HWEXEC is gone, _PAGE_EXEC is now only
defined by CPUs that can do something with it, and the myriad of
#ifdef's in the I$/D$ coherency code is reduced to 2 cases that
hopefully should cover everything.
The logic on BookE is a little bit different than what it was though
not by much. Since now, _PAGE_EXEC will be set by the generic code
for executable pages, we need to filter out if they are unclean and
recover it. However, I don't expect the code to be more bloated than
it already was in that area due to that change.
I could boast that this brings proper enforcing of per-page execute
permissions to all BookE and 40x but in fact, we've had that now for
some time as a side effect of my previous rework in that area (and
I didn't even know it :-) We would only enable execute permission if
the page was cache clean and we would only cache clean it if we took
and exec fault. Since we now enforce that the later only work if
VM_EXEC is part of the VMA flags, we de-fact already enforce per-page
execute permissions... Unless I missed something
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
irda/sa1100_ir: fix broken netdev_ops conversion
irda/au1k_ir: fix broken netdev_ops conversion
pkt_sched: Fix bogon in tasklet_hrtimer changes.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Validate linear D-TLB misses.
sparc64: Update defconfig.
sparc32: Update defconfig.
sparc32: Kill trap table freeing code.
sparc: sys32.S incorrect compat-layer splice() system call
sparc: Use page_fault_out_of_memory() for VM_FAULT_OOM.
sparc64: Sign extend length arg to truncate syscalls when compat.
sparc: Fix cleanup crash in bbc_envctrl_cleanup()
|
|
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for sa1100_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for au1k_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids having a short glitch if the desired initial value is not
the same as what was previously in the data register.
Signed-off-by: Michael Barkowski <michaelbarkowski@ruggedcom.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
When page alloc debugging is not enabled, we essentially accept any
virtual address for linear kernel TLB misses. But with kgdb, kernel
address probing, and other facilities we can try to access arbitrary
crap.
So, make sure the address we miss on will translate to physical memory
that actually exists.
In order to make this work we have to embed the valid address bitmap
into the kernel image. And in order to make that less expensive we
make an adjustment, in that the max physical memory address is
decreased to "1 << 41", even on the chips that support a 42-bit
physical address space. We can do this because bit 41 indicates
"I/O space" and thus covers non-memory ranges.
The result of this is that:
1) kpte_linear_bitmap shrinks from 2K to 1K in size
2) we need 64K more for the valid address bitmap
We can't let the valid address bitmap be dynamically allocated
once we start using it to validate TLB misses, otherwise we have
crazy issues to deal with wrt. recursive TLB misses and such.
If we're in a TLB miss it could be the deepest trap level that's legal
inside of the cpu. So if we TLB miss referencing the bitmap, the cpu
will be out of trap levels and enter RED state.
To guard against out-of-range accesses to the bitmap, we have to check
to make sure no bits in the physical address above bit 40 are set. We
could export and use last_valid_pfn for this check, but that's just an
unnecessary extra memory reference.
On the plus side of all this, since we load all of these translations
into the special 4MB mapping TSB, and we check the TSB first for TLB
misses, there should be absolutely no real cost for these new checks
in the TLB miss path.
Reported-by: heyongli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Fix typo in read() output generation
perf tools: Check perf.data owner
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
dma-debug: Fix check_unmap null pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevent: Prevent dead lock on clockevents_lock
timers: Drop write permission on /proc/timer_list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix too large stack usage in do_one_initcall()
tracing: handle broken names in ftrace filter
ftrace: Unify effect of writing to trace_options and option/*
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix build with older binutils and consolidate linker script
x86: Fix an incorrect argument of reserve_bootmem()
x86: add vmlinux.lds to targets in arch/x86/boot/compressed/Makefile
xen: rearrange things to fix stackprotector
x86: make sure load_percpu_segment has no stackprotector
i386: Fix section mismatches for init code with !HOTPLUG_CPU
x86, pat: Allow ISA memory range uncacheable mapping requests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: Improve error message that changing journaling mode on remount is not possible
ext3: Update Kconfig description of EXT3_DEFAULTS_TO_ORDERED
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/misc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: pcm_lib: fix unsorted list constraint handling
sound: vx222: fix input level control range check
ALSA: ali5451: fix timeout handling in snd_ali_{codecs,timer}_ready()
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] ar7_wdt: fix path to ar7-specific headers
|
|
When I rewrote tty ldisc code to use proper reference counts (commits
65b770468e98 and cbe9352fa08f) in order to avoid a race with hangup, the
test-program that Eric Biederman used to trigger the original problem
seems to have exposed another long-standing bug: the hangup code did the
'tty_ldisc_halt()' to stop any buffer flushing activity, but unlike the
other call sites it never actually flushed any pending work.
As a result, if you get just the right timing, the pending work may be
just about to execute (ie the timer has already triggered and thus
cancel_delayed_work() was a no-op), when we then re-initialize the ldisc
from under it.
That, in turn, results in various random problems, usually seen as a
NULL pointer dereference in run_timer_softirq() or a BUG() in
worker_thread (but it can be almost anything).
Fix it by adding the required 'flush_scheduled_work()' after doing the
tty_ldisc_halt() (this also requires us to move the ldisc halt to before
taking the ldisc mutex in order to avoid a deadlock with the workqueue
executing do_tty_hangup, which requires the mutex).
The locking should be cleaned up one day (the requirement to do this
outside the ldisc_mutex is very annoying, and weakens the lock), but
that's a larger and separate undertaking.
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Xiaotian Feng <xtfeng@gmail.com>
Tested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
- Add usb node;
- Configure pins and clocks;
- Enable USB function in BCSR.
The support was successfully tested using serial and ethernet gadget
drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
mpc8272_ads.c is using BCSR bits definitions from pq2ads.h, but
according to User's Guide the bits are wrong for MPC8272ADS boards
(I guess definitions from pq2ads should only be used for PQ2FADS
boards).
So, let's introduce our own definitions for MPC8272ADS, and don't
include pq2ads.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch simply adds sdhci node to the device tree.
We specify clock-frequency manually, so that eSDHC will work without
upgrading U-Boot. Though, that'll only work for default setup (1500
MHz) on new board revisions. For non-default setups, it's recommended
to upgrade U-Boot, since it will fixup clock-frequency automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
binutils prior to 2.17 can't deal with the currently possible
situation of a new segment following the per-CPU segment, but
that new segment being empty - objcopy misplaces the .bss (and
perhaps also the .brk) sections outside of any segment.
However, the current ordering of sections really just appears
to be the effect of cumulative unrelated changes; re-ordering
things allows to easily guarantee that the segment following
the per-CPU one is non-empty, and at once eliminates the need
for the bogus data.init2 segment.
Once touching this code, also use the various data section
helper macros from include/asm-generic/vmlinux.lds.h.
-v2: fix !SMP builds.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <sam@ravnborg.org>
LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
snd_interval_list() expected a sorted list but did not document this, so
there are drivers that give it an unsorted list. To fix this, change
the algorithm to work with any list.
This fixes the "Slave PCM not usable" error with USB devices that have
multiple alternate settings with sample rates in decreasing order, such
as the Philips Askey VC010 WebCam.
http://bugzilla.kernel.org/show_bug.cgi?id=14028
Reported-and-tested-by: Andrzej <adkadk@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Reported by Stephen Rothwell, luckily it's harmless:
net/sched/sch_api.c: In function 'qdisc_watchdog':
net/sched/sch_api.c:460: warning: initialization from incompatible pointer type
net/sched/sch_cbq.c: In function 'cbq_undelay':
net/sched/sch_cbq.c:595: warning: initialization from incompatible pointer type
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The earlier mpc8560 CPUs don't have the RSTCR at 0xe00b0
in the GUTS. The generic reboot code uses this tag to
determine if it should be using the RSTCR for reboot, so
remove it from the board definition.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some CPU, like the MPC8560 don't have a RSTCR in the Global
Utilities Block. These boards will implement their own reboot
call, and not use this code, so we should only warn about the
absence of the GUTS RSTCR when the default reboot code is used.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The existing fsl_rstcr_restart function is not applicable to the
mpc8560. The Global Utilities Block on this earlier CPU doesn't have
the control/reset register at 0xe00b0. This implements a board
specific reset function that uses the RCR(Reset Control Register) of
the sbc8560's EPLD to do a reset.
Signed-off-by: Liang Li <Liang.Li@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
With flash partition entries in the DTS file, MTD might as well
be enabled in the defconfig. In a similar vein, enable USB and
enough related options (SCSI/ext2/ext3) so that a user can read
and write to a generic USB flash drive as well.
Also, this board only has the two default SOC UARTs, so adjust the
UART config accordingly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Allows interrupts to occur on the sbc834x. Currently PCI devices
get assigned an incorrect IRQ and so the interrupt count never
increases. This was tested with the 82546GB based dual port E1000
PCI-X NIC which uses two distinct IRQ lines on the one card.
root@localhost:/root> cat /proc/interrupts | grep eth
17: 78 IPIC Level eth1
48: 27121 IPIC Level eth0
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x
local bus, so add a localbus node in DTS with MTD partitions.
The recent U-boot commit fe613cdd4eb moves u-boot to the beginning
of flash, hence the legacy label on the partition at the end of flash.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Since only one of the SoC USB devices is brought out to a physical
connector on the board, remove the 2nd (USB-DR) node from the DTS.
Having it present and USB enabled will cause a hang at boot.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add support for the P2020RDB reference board from Freescale.
Overview of P2020RDB platform
- DDR
DDR2 1G
- NOR Flash
16MByte
- NAND Flash
32MByte
- 3 Ethernet interfaces
1) etSEC1
- RGMII
- connected to a 5 port Vitesse Switch(VSC7385)
- Switch is memory mapped through eLBC interface(CS#2)
- IRQ1
2) etSEC2
- SGMII
- connected to VSC8221
- IRQ2
3) etSEC3
- RGMII
- connected to VSC8641
- IRQ3
- 2 1X PCIe interfaces
- SD/MMC ,USB
- SPI EEPROM
- Serial I2C EEPROM
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The MMUCSR is now defined as part of the Book-3E architecture so we
can move it into mmu-book3e.h and add some of the additional bits
defined by the architecture specs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
- add I2C support
- add FCC1 and FCC2 support
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Commit 76db6d9500caeaa774a3e32a997eba30bbdc176b (nfs41: add session setup
to the state manager) introduces an infinite loop possibility in the NFSv4
state manager. By first checking nfs4_has_session() before clearing the
NFS4CLNT_SESSION_SETUP flag, it allows for a situation where someone sets
that flag, but it never gets cleared, and so the state manager loops.
In fact commit c3fad1b1aaf850bf692642642ace7cd0d64af0a3 (nfs41: add session
reset to state manager) causes this to happen every time we get a network
partition error.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2/dlm: Wait on lockres instead of erroring cancel requests
ocfs2: Add missing lock name
ocfs2: Don't oops in ocfs2_kill_sb on a failed mount
ocfs2: release the buffer head in ocfs2_do_truncate.
ocfs2: Handle quota file corruption more gracefully
|
|
* 'fixes' of git://git.marvell.com/orion:
[ARM] Orion NAND: Make asm volatile avoid GCC pushing ldrd out of the loop
[ARM] Kirkwood: enable eSATA on QNAP TS-219P
[ARM] Kirkwood: __init requires linux/init.h
|
|
2.6.30's commit 8a0bdec194c21c8fdef840989d0d7b742bb5d4bc removed
user_shm_lock() calls in hugetlb_file_setup() but left the
user_shm_unlock call in shm_destroy().
In detail:
Assume that can_do_hugetlb_shm() returns true and hence user_shm_lock()
is not called in hugetlb_file_setup(). However, user_shm_unlock() is
called in any case in shm_destroy() and in the following
atomic_dec_and_lock(&up->__count) in free_uid() is executed and if
up->__count gets zero, also cleanup_user_struct() is scheduled.
Note that sched_destroy_user() is empty if CONFIG_USER_SCHED is not set.
However, the ref counter up->__count gets unexpectedly non-positive and
the corresponding structs are freed even though there are live
references to them, resulting in a kernel oops after a lots of
shmget(SHM_HUGETLB)/shmctl(IPC_RMID) cycles and CONFIG_USER_SCHED set.
Hugh changed Stefan's suggested patch: can_do_hugetlb_shm() at the
time of shm_destroy() may give a different answer from at the time
of hugetlb_file_setup(). And fixed newseg()'s no_id error path,
which has missed user_shm_unlock() ever since it came in 2.6.9.
Reported-by: Stefan Huber <shuber2@gmail.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Tested-by: Stefan Huber <shuber2@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix radeon_gem_busy_ioctl harder.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
favr32: improve touchscreen response
avr32/lib: fix unaligned memcpy where len < 4
avr32/lib: fix unaligned memcpy()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ucb1400_ts - enable interrupt unconditionally
Input: ucb1400_ts - enable ADC Filter
Input: wacom - don't use on-stack memory for report buffers
Input: iforce - support new revision of ACT LABS Force RS
Input: joydev - decouple axis and button map ioctls from input constants
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
smc91x: let smc91x work well under netpoll
pxaficp-ir: remove incorrect net_device_ops
NET: llc, zero sockaddr_llc struct
drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
netpoll: warning for ndo_start_xmit returns with interrupts enabled
net: Fix Micrel KSZ8842 Kconfig description
netfilter: xt_quota: fix wrong return value (error case)
ipv6: Fix commit 63d9950b08184e6531adceb65f64b429909cc101 (ipv6: Make v4-mapped bindings consistent with IPv4)
E100: fix interaction with swiotlb on X86.
pkt_sched: Convert CBQ to tasklet_hrtimer.
pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer
rtl8187: always set MSR_LINK_ENEDCA flag with RTL8187B
ibm_newemac: emac_close() needs to call netif_carrier_off()
net: fix ks8851 build errors
net: Rename MAC platform driver for w90p910 platform
yellowfin: Fix buffer underrun after dev_alloc_skb() failure
orinoco: correct key bounds check in orinoco_hw_get_tkip_iv
mac80211: fix todo lock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
ima: hashing large files bug fix
kernel_read: redefine offset type
|
