| Age | Commit message (Collapse) | Author |
|---|
|
Pointless to iterate other devices looking for a super, when
we have a bdi mapping.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Debug traces show that in per-bdi writeback, the inode under writeback
almost always get redirtied by a busy dirtier. We used to call
redirty_tail() in this case, which could delay inode for up to 30s.
This is unacceptable because it now happens so frequently for plain cp/dd,
that the accumulated delays could make writeback of big files very slow.
So let's distinguish between data redirty and metadata only redirty.
The first one is caused by a busy dirtier, while the latter one could
happen in XFS, NFS, etc. when they are doing delalloc or updating isize.
The inode being busy dirtied will now be requeued for next io, while
the inode being redirtied by fs will continue to be delayed to avoid
repeated IO.
CC: Jan Kara <jack@suse.cz>
CC: Theodore Ts'o <tytso@mit.edu>
CC: Dave Chinner <david@fromorbit.com>
CC: Chris Mason <chris.mason@oracle.com>
CC: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Currently we pin the inode->i_sb for every single inode. This
increases cache traffic on sb->s_umount sem. Lets instead
cache the inode sb pin state and keep the super_block pinned
for as long as keep writing out inodes from the same
super_block.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
If we only moved inodes from a single super_block to the temporary
list, there's no point in doing a resort for multiple super_blocks.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
__mark_inode_dirty adds inode to wb dirty list in random order. If a disk has
several partitions, writeback might keep spindle moving between partitions.
To reduce the move, better write big chunk of one partition and then move to
another. Inodes from one fs usually are in one partion, so idealy move indoes
from one fs together should reduce spindle move. This patch tries to address
this. Before per-bdi writeback is added, the behavior is write indoes
from one fs first and then another, so the patch restores previous behavior.
The loop in the patch is a bit ugly, should we add a dirty list for each
superblock in bdi_writeback?
Test in a two partition disk with attached fio script shows about 3% ~ 6%
improvement.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
And throw some comments in there, too.
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Make the if-else straight in writeback_single_inode().
No behavior change.
Cc: Jan Kara <jack@suse.cz>
Cc: Michael Rubin <mrubin@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Fix the kupdate case, which disregards wbc.more_io and stop writeback
prematurely even when there are more inodes to be synced.
wbc.more_io should always be respected.
Also remove the pages_skipped check. It will set when some page(s) of some
inode(s) cannot be written for now. Such inodes will be delayed for a while.
This variable has nothing to do with whether there are other writeable inodes.
CC: Jan Kara <jack@suse.cz>
CC: Dave Chinner <david@fromorbit.com>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Treat bdi_start_writeback(0) as a special request to do background write,
and stop such work when we are below the background dirty threshold.
Also simplify the (nr_pages <= 0) checks. Since we already pass in
nr_pages=LONG_MAX for WB_SYNC_ALL and background writes, we don't
need to worry about it being decreased to zero.
Reported-by: Richard Kennedy <richard@rsk.demon.co.uk>
CC: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Some filesystem may choose to write much more than ratelimit_pages
before calling balance_dirty_pages_ratelimited_nr(). So it is safer to
determine number to write based on real number of dirtied pages.
Otherwise it is possible that
loop {
btrfs_file_write(): dirty 1024 pages
balance_dirty_pages(): write up to 48 pages (= ratelimit_pages * 1.5)
}
in which the writeback rate cannot keep up with dirty rate, and the
dirty pages go all the way beyond dirty_thresh.
The increased write_chunk may make the dirtier more bumpy.
So filesystems shall be take care not to dirty too much at
a time (eg. > 4MB) without checking the ratelimit.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
If all inodes are under writeback (e.g. in case when there's only one inode
with dirty pages), wb_writeback() with WB_SYNC_NONE work basically degrades
to busylooping until I_SYNC flags of the inode is cleared. Fix the problem by
waiting on I_SYNC flags of an inode on b_more_io list in case we failed to
write anything.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event, powerpc: Fix compilation after big perf_counter rename
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vegard/kmemcheck
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vegard/kmemcheck:
kmemcheck: add missing braces to do-while in kmemcheck_annotate_bitfield
kmemcheck: update documentation
kmemcheck: depend on HAVE_ARCH_KMEMCHECK
kmemcheck: remove useless check
kmemcheck: remove duplicated #include
|
|
* 'for-2.6.32' of git://linux-nfs.org/~bfields/linux: (68 commits)
nfsd4: nfsv4 clients should cross mountpoints
nfsd: revise 4.1 status documentation
sunrpc/cache: avoid variable over-loading in cache_defer_req
sunrpc/cache: use list_del_init for the list_head entries in cache_deferred_req
nfsd: return success for non-NFS4 nfs4_state_start
nfsd41: Refactor create_client()
nfsd41: modify nfsd4.1 backchannel to use new xprt class
nfsd41: Backchannel: Implement cb_recall over NFSv4.1
nfsd41: Backchannel: cb_sequence callback
nfsd41: Backchannel: Setup sequence information
nfsd41: Backchannel: Server backchannel RPC wait queue
nfsd41: Backchannel: Add sequence arguments to callback RPC arguments
nfsd41: Backchannel: callback infrastructure
nfsd4: use common rpc_cred for all callbacks
nfsd4: allow nfs4 state startup to fail
SUNRPC: Defer the auth_gss upcall when the RPC call is asynchronous
nfsd4: fix null dereference creating nfsv4 callback client
nfsd4: fix whitespace in NFSPROC4_CLNT_CB_NULL definition
nfsd41: sunrpc: add new xprt class for nfsv4.1 backchannel
sunrpc/cache: simplify cache_fresh_locked and cache_fresh_unlocked.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Remove duplicate Kconfig entry
HID: consolidate connect and disconnect into core code
HID: fix non-atomic allocation in hid_input_report
|
|
Add a driver for the the Consumer IR (CIR) functionality of the Winbond
WPCD376I chipset (found on e.g. Intel DG45FC motherboards).
Signed-off-by: David Härdeman <david@hardeman.nu>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The shutdown method is used by the winbond cir driver to setup the
hardware for wake-from-S5.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On resume from suspend, the driver currently resets the logical state as
if it was brought up from halt. This patch uses the
dev_pm_ops.resume/restore methods to synchronize the hardware with the
memorized logical state, in effect bringing back the accelerometer and
backlight to the state prior to suspend. Works for both suspend to ram
and hibernation. The patch has zero effect on the running state.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If already requested, gpio_data and irq should be freed in the case of an
error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Occasionally it is helpful to be able to turn a temperature sensor off
(for example if it's making unwanted electrical noise). This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The ADM1023 temperature sensor supports higher resolution for its external
sensor (sensitivity of 1/8 deg C). This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.
Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This enabled power management functions for the SPI transport layer of the
lis3 devices. The device's suspend mode is only entered in case no wakeup
threshold has been given. In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.
[randy.dunlap@oracle.com: fix lis3-spi for CONFIG_PM=n]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This offers a way for platforms to define flags and thresholds for the
free-fall/wakeup functions of the lis302d chips.
More registers needed to be seperated as they are specific to the
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bit 0x80 in CTRL_REG3 is an ACTIVE_LOW rather than an ACTIVE_HIGH
function, I got that wrong during my last change.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Enable the coretemp driver on an Intel Atom.
I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load). Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add checks for Blackfin-specific issues that seem to crop up from time to
time. In particular, we have helper macros to break a 32bit address into
the hi/lo parts, and we want to make sure people use the csync/ssync
variant that includes fun anomaly workarounds.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Limit our type matcher to the s/u/le/be etc sizes that actually exist to
prevent miss categorising s2 as a type. Fix up the spelling of the error
also.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We should not recommend braces for the following:
#define pr_fmt(fmt) "%s: " fmt, __func__
allow things with double quotes round them to avoid this check.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact:
- More verbose help/usage message.
- Make the option -f an alias for --file.
- On -h, --help, and --version display help message and exit(0).
- With no FILE(s) given, exit(1) with "no input files".
- On invalid options display help/usage and exit(1).
Based on a patch by Pavel Machek.
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ensure we terminate when there are no futher continuation lines when
trying to determine relative indent of conditionals and their blocks.
Reported-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes the sanitation process in checkpatch.pl so that it blocks out
the text after a C99 style comment the same way it does with block style
comments. This prevents the text from getting processed as regular code.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
An else cannot start a type, it would have to be within a block after the
else. This can trigger false modifier matching.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add kerneldoc annotations for function formals of type struct flex_array
and gfp_t which are currently lacking.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
FLEX_ARRAY_INIT(element_size, total_nr_elements) cannot determine if
either parameter is valid, so flex arrays which are statically allocated
with this interface can easily become corrupted or reference beyond its
allocated memory.
This removes FLEX_ARRAY_INIT() as a struct flex_array initializer since no
initializer may perform the required checking. Instead, the array is now
defined with a new interface:
DEFINE_FLEX_ARRAY(name, element_size, total_nr_elements)
This may be prefixed with `static' for file scope.
This interface includes compile-time checking of the parameters to ensure
they are valid. Since the validity of both element_size and
total_nr_elements depend on FLEX_ARRAY_BASE_SIZE and FLEX_ARRAY_PART_SIZE,
the kernel build will fail if either of these predefined values changes
such that the array parameters are no longer valid.
Since BUILD_BUG_ON() requires compile time constants, several of the
static inline functions that were once local to lib/flex_array.c had to be
moved to include/linux/flex_array.h.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new function to the flex_array API:
int flex_array_shrink(struct flex_array *fa)
This function will free all unused second-level pages. Since elements are
now poisoned if they are not allocated with __GFP_ZERO, it's possible to
identify parts that consist solely of unused elements.
flex_array_shrink() returns the number of pages freed.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Newly initialized flex_array's and/or flex_array_part's are now poisoned
with a new poison value, FLEX_ARRAY_FREE. It's value is similar to
POISON_FREE used in the various slab allocators, but is different to
distinguish between flex array's poisoned kmem and slab allocator poisoned
kmem.
This will allow us to identify flex_array_part's that only contain free
elements (and free them with an addition to the flex_array API). This
could also be extended in the future to identify `get' uses on elements
that have not been `put'.
If __GFP_ZERO is passed for a part's gfp mask, the poisoning is avoided.
These elements are considered to be in-use since they have been
initialized.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new function to the flex_array API:
int flex_array_clear(struct flex_array *fa,
unsigned int element_nr)
This function will zero the element at element_nr in the flex_array.
Although this is equivalent to using flex_array_put() and passing a
pointer to zero'd memory, flex_array_clear() does not require such a
pointer to memory that would most likely need to be allocated on the
caller's stack which could be significantly large depending on
element_size.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A couple of new uses of separate "P: name" "M: address" lines are
converted to single line "M: name <address>"
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Otherwise 'arch/arm/*omap*/foo.c' wouldn't match
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Previous behavior was "bottom-up" in each section from the pattern "F:"
entry that matched. Now information is entered into the various lists in
the "as entered" order for each matched section.
This also allows the F: entry to be put anywhere in a section, not just as
the last entries in the section.
And a couple of improvements:
Don't alphabetically sort before outputting the matched scm, status,
subsystem and web sections.
Ignore content after a single email address so these entries are acceptable
M: name <address> whatever other comment
And a fix:
Make an M: entry without a name again use the name from an immediately
preceding P: line if it exists.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Allow control over the elimination of duplicate email names and addresses
--remove-duplicates will use the first email name or address presented
--noremove-duplicates will emit all names and addresses
--remove-duplicates is enabled by default
For instance:
$ ./scripts/get_maintainer.pl -f drivers/char/tty_ioctl.c
Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox <alan@linux.intel.com>
Mike Frysinger <vapier@gentoo.org>
Alexey Dobriyan <adobriyan@gmail.com>
linux-kernel@vger.kernel.org
$ ./scripts/get_maintainer.pl -f --noremove-duplicates drivers/char/tty_ioctl.c
Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox <alan@redhat.com>
Alan Cox <alan@linux.intel.com>
Alan Cox <alan@lxorguk.ukuu.org.uk>
Mike Frysinger <vapier@gentoo.org>
Alexey Dobriyan <adobriyan@gmail.com>
linux-kernel@vger.kernel.org
Using --remove-duplicates could eliminate multiple maintainers that
share the same name but not the same email address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a person sets a separator, it's only used if --nomultiline is set.
Don't make the command line also include --nomultiline in that case.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add reading and using .mailmap file if it exists
Convert address entries in .mailmap to first encountered address
Don't terminate shell commands with \n
Strip characters found after sign-offs by: name <address> [stripped]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
