| Age | Commit message (Collapse) | Author |
|---|
|
The second call to cpu_clear() is redundant, as we've already removed
the CPU from cpu_online_map before calling migrate_platform_irqs().
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <aegl@agluck-desktop.(none)>
|
|
This reverts commit e7b140365b86aaf94374214c6f4e6decbee2eb0a.
Commit e7b14036 removes the targetted disabled CPU from the
cpu_online_map after calls to migrate_platform_irqs and fixup_irqs.
Paul McKenney states that the reasoning behind the patch was to
prevent irq handlers from running on CPUs marked offline because:
RCU happily ignores CPUs that don't have their bits set in
cpu_online_map, so if there are RCU read-side critical sections
in the irq handlers being run, RCU will ignore them. If the
other CPUs were running, they might sequence through the RCU
state machine, which could result in data structures being
yanked out from under those irq handlers, which in turn could
result in oopses or worse.
Unfortunately, both ia64 functions above look at cpu_online_map to find
a new CPU to migrate interrupts onto. This means we can potentially
migrate an interrupt off ourself back to... ourself. Uh oh.
This causes an oops when we finally try to process pending interrupts on
the CPU we want to disable. The oops results from calling __do_IRQ with
a NULL pt_regs:
Unable to handle kernel NULL pointer dereference (address 0000000000000040)
Call Trace:
[<a000000100016930>] show_stack+0x50/0xa0
sp=e0000009c922fa00 bsp=e0000009c92214d0
[<a0000001000171a0>] show_regs+0x820/0x860
sp=e0000009c922fbd0 bsp=e0000009c9221478
[<a00000010003c700>] die+0x1a0/0x2e0
sp=e0000009c922fbd0 bsp=e0000009c9221438
[<a0000001006e92f0>] ia64_do_page_fault+0x950/0xa80
sp=e0000009c922fbd0 bsp=e0000009c92213d8
[<a00000010000c7a0>] ia64_native_leave_kernel+0x0/0x270
sp=e0000009c922fc60 bsp=e0000009c92213d8
[<a0000001000ecdb0>] profile_tick+0xd0/0x1c0
sp=e0000009c922fe30 bsp=e0000009c9221398
[<a00000010003bb90>] timer_interrupt+0x170/0x3e0
sp=e0000009c922fe30 bsp=e0000009c9221330
[<a00000010013a800>] handle_IRQ_event+0x80/0x120
sp=e0000009c922fe30 bsp=e0000009c92212f8
[<a00000010013aa00>] __do_IRQ+0x160/0x4a0
sp=e0000009c922fe30 bsp=e0000009c9221290
[<a000000100012290>] ia64_process_pending_intr+0x2b0/0x360
sp=e0000009c922fe30 bsp=e0000009c9221208
[<a0000001000112d0>] fixup_irqs+0xf0/0x2a0
sp=e0000009c922fe30 bsp=e0000009c92211a8
[<a00000010005bd80>] __cpu_disable+0x140/0x240
sp=e0000009c922fe30 bsp=e0000009c9221168
[<a0000001006c5870>] take_cpu_down+0x50/0xa0
sp=e0000009c922fe30 bsp=e0000009c9221148
[<a000000100122610>] stop_cpu+0xd0/0x200
sp=e0000009c922fe30 bsp=e0000009c92210f0
[<a0000001000e0440>] kthread+0xc0/0x140
sp=e0000009c922fe30 bsp=e0000009c92210c8
[<a000000100014ab0>] kernel_thread_helper+0xd0/0x100
sp=e0000009c922fe30 bsp=e0000009c92210a0
[<a00000010000a4c0>] start_kernel_thread+0x20/0x40
sp=e0000009c922fe30 bsp=e0000009c92210a0
I don't like this revert because it is fragile. ia64 is getting lucky
because we seem to only ever process timer interrupts in this path, but
if we ever race with an IPI here, we definitely use RCU and have the
potential of hitting an oops that Paul describes above.
Patching ia64's timer_interrupt() to check for NULL pt_regs is
insufficient though, as we still hit the above oops.
As a short term solution, I do think that this revert is the right
answer. The revert hold up under repeated testing (24+ hour test runs)
with this setup:
- 8-way rx6600
- randomly toggling CPU online/offline state every 2 seconds
- running CPU exercisers, memory hog, disk exercisers, and
network stressors
- average system load around ~160
In the long term, we really need to figure out why we set pt_regs = NULL
in ia64_process_pending_intr(). If it turns out that it is unnecessary
to do so, then we could safely re-introduce e7b14036 (along with some
other logic to be smarter about migrating interrupts).
One final note: x86 also removes the disabled CPU from cpu_online_map
and then re-enables interrupts for 1ms, presumably to handle any pending
interrupts:
arch/x86/kernel/irq_32.c (and irq_64.c):
cpu_disable_common:
[remove cpu from cpu_online_map]
fixup_irqs():
for_each_irq:
[break CPU affinities]
local_irq_enable();
mdelay(1);
local_irq_disable();
So they are doing implicitly what ia64 is doing explicitly.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <aegl@agluck-desktop.(none)>
|
|
BTE_MAX_XFER is wrong. It is one greater than the number of cache
lines the BTE is actually able to transfer. If you request a transfer
of exactly BTE_MAX_XFER size, you trip a very cryptic BUG_ON() which
should certainly be made more clear.
This patch fixes that constant and also cleans up the BUG_ON()s in
arch/ia64/sn/kernel/bte.c to test one condition per line.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <aegl@agluck-desktop.(none)>
|
|
ia64 only defines __early_pfn_to_nid() for SPARSEMEM && NUMA configurations,
so the recent:
commit: f2dbcfa738368c8a40d4a5f0b65dc9879577cb21
mm: clean up for early_pfn_to_nid()
ends up with some link problems for certain configuration files.
Fix arch/ia64/Kconfig to only define HAVE_ARCH_EARLY_PFN_TO_NID in the
cases where we do provide this function.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
block: fix booting from partitioned md array
block: revert part of 18ce3751ccd488c78d3827e9f6bf54e6322676fb
cciss: PCI power management reset for kexec
paride/pg.c: xs(): &&/|| confusion
fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
block: fix bad definition of BIO_RW_SYNC
bsg: Fix sense buffer bug in SG_IO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
omap_hsmmc: Change while(); loops with finite version
omap_hsmmc: recover from transfer failures
omap_hsmmc: only MMC1 allows HCTL.SDVS != 1.8V
omap_hsmmc: card detect irq bugfix
sdhci: fix led naming
mmc_test: fix basic read test
s3cmci: Fix hangup in do_pio_write()
Revert "sdhci: force high speed capability on some controllers"
MMC: fix bug - SDHC card capacity not correct
|
|
Enhanced lockdep coverage of __GFP_NOFS turned up this new lockdep
assert:
[ 1093.677775]
[ 1093.677781] =================================
[ 1093.680031] [ INFO: inconsistent lock state ]
[ 1093.680031] 2.6.29-rc5-tip-01504-gb49eca1-dirty #1
[ 1093.680031] ---------------------------------
[ 1093.680031] inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
[ 1093.680031] kswapd0/308 [HC0[0]:SC0[0]:HE1:SE1] takes:
[ 1093.680031] (&inode->inotify_mutex){+.+.?.}, at: [<c0205942>] inotify_inode_is_dead+0x20/0x80
[ 1093.680031] {RECLAIM_FS-ON-W} state was registered at:
[ 1093.680031] [<c01696b9>] mark_held_locks+0x43/0x5b
[ 1093.680031] [<c016baa4>] lockdep_trace_alloc+0x6c/0x6e
[ 1093.680031] [<c01cf8b0>] kmem_cache_alloc+0x20/0x150
[ 1093.680031] [<c040d0ec>] idr_pre_get+0x27/0x6c
[ 1093.680031] [<c02056e3>] inotify_handle_get_wd+0x25/0xad
[ 1093.680031] [<c0205f43>] inotify_add_watch+0x7a/0x129
[ 1093.680031] [<c020679e>] sys_inotify_add_watch+0x20f/0x250
[ 1093.680031] [<c010389e>] sysenter_do_call+0x12/0x35
[ 1093.680031] [<ffffffff>] 0xffffffff
[ 1093.680031] irq event stamp: 60417
[ 1093.680031] hardirqs last enabled at (60417): [<c018d5f5>] call_rcu+0x53/0x59
[ 1093.680031] hardirqs last disabled at (60416): [<c018d5b9>] call_rcu+0x17/0x59
[ 1093.680031] softirqs last enabled at (59656): [<c0146229>] __do_softirq+0x157/0x16b
[ 1093.680031] softirqs last disabled at (59651): [<c0106293>] do_softirq+0x74/0x15d
[ 1093.680031]
[ 1093.680031] other info that might help us debug this:
[ 1093.680031] 2 locks held by kswapd0/308:
[ 1093.680031] #0: (shrinker_rwsem){++++..}, at: [<c01b0502>] shrink_slab+0x36/0x189
[ 1093.680031] #1: (&type->s_umount_key#4){+++++.}, at: [<c01e6d77>] shrink_dcache_memory+0x110/0x1fb
[ 1093.680031]
[ 1093.680031] stack backtrace:
[ 1093.680031] Pid: 308, comm: kswapd0 Not tainted 2.6.29-rc5-tip-01504-gb49eca1-dirty #1
[ 1093.680031] Call Trace:
[ 1093.680031] [<c016947a>] valid_state+0x12a/0x13d
[ 1093.680031] [<c016954e>] mark_lock+0xc1/0x1e9
[ 1093.680031] [<c016a5b4>] ? check_usage_forwards+0x0/0x3f
[ 1093.680031] [<c016ab74>] __lock_acquire+0x2c6/0xac8
[ 1093.680031] [<c01688d9>] ? register_lock_class+0x17/0x228
[ 1093.680031] [<c016b3d3>] lock_acquire+0x5d/0x7a
[ 1093.680031] [<c0205942>] ? inotify_inode_is_dead+0x20/0x80
[ 1093.680031] [<c08824c4>] __mutex_lock_common+0x3a/0x4cb
[ 1093.680031] [<c0205942>] ? inotify_inode_is_dead+0x20/0x80
[ 1093.680031] [<c08829ed>] mutex_lock_nested+0x2e/0x36
[ 1093.680031] [<c0205942>] ? inotify_inode_is_dead+0x20/0x80
[ 1093.680031] [<c0205942>] inotify_inode_is_dead+0x20/0x80
[ 1093.680031] [<c01e6672>] dentry_iput+0x90/0xc2
[ 1093.680031] [<c01e67a3>] d_kill+0x21/0x45
[ 1093.680031] [<c01e6a46>] __shrink_dcache_sb+0x27f/0x355
[ 1093.680031] [<c01e6dc5>] shrink_dcache_memory+0x15e/0x1fb
[ 1093.680031] [<c01b05ed>] shrink_slab+0x121/0x189
[ 1093.680031] [<c01b0d12>] kswapd+0x39f/0x561
[ 1093.680031] [<c01ae499>] ? isolate_pages_global+0x0/0x233
[ 1093.680031] [<c0157eae>] ? autoremove_wake_function+0x0/0x43
[ 1093.680031] [<c01b0973>] ? kswapd+0x0/0x561
[ 1093.680031] [<c0157daf>] kthread+0x41/0x82
[ 1093.680031] [<c0157d6e>] ? kthread+0x0/0x82
[ 1093.680031] [<c01043ab>] kernel_thread_helper+0x7/0x10
inotify_handle_get_wd() does idr_pre_get() which does a
kmem_cache_alloc() without __GFP_FS - and is hence deadlockable under
extreme MM pressure.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: MinChan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gpio_get_value() returns 0 or nonzero, but getmiso() expects 0 or 1.
Sanitize the value to a 0/1 boolean.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since I don't work for SUSE any more and the bwalle@suse.de address is
invalid, correct it in the copyright headers and documentation.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Build breaks when DELL_LAPTOP=y and POWER_SUPPLY=m. DELL_LAPTOP needs to
depend on POWER_SUPPLY.
dell-laptop.c:(.text+0x1ef3c4): undefined reference to `power_supply_is_system_supplied'
dell-laptop.c:(.text+0x1ef45e): undefined reference to `power_supply_is_system_supplied'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Otherwise, these don't work when called from 32-bit userspace on 64-bit
kernels.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Submenus of the graphics support "Support for frame buffer devices" and
"Direct Rendering Manager (XFree86 4.1.0 and higher DRI support)" are
broken in half after latest changes for Intel 915 mode setting support.
The DRM subsection is broken because one option is put outside the choice
section it depends on.
The frame buffers part is broken then due to circular dependency. Fix
this by make Intel frame buffers depend on CONFIG_INTEL_AGP.
Kconfigs are broken by d2f59357700487a8b944f4f7777d1e97cf5ea2ed
("drm/i915: select framebuffer support automatically").
This is probably not only way to fix this.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The floppy driver requests an I/O port it doesn't need, and sometimes this
causes a conflict with a motherboard device reported by PNPBIOS.
This patch makes the floppy driver request and release only the ports it
actually uses. It also factors out the request/release stuff and the
io-ports list so they're all in one place now.
The current floppy driver uses only these ports:
0x3f2 (FD_DOR)
0x3f4 (FD_STATUS)
0x3f5 (FD_DATA)
0x3f7 (FD_DCR/FD_DIR)
but it requests 0x3f2-0x3f5 and 0x3f7, which includes the unused port
0x3f3.
Some BIOSes report 0x3f3 as a motherboard resource. The PNP system driver
reserves that, which causes a conflict when the floppy driver requests
0x3f2-0x3f5 later.
Philippe reported that this conflict broke the floppy driver between
2.6.11 and 2.6.22. His PNPBIOS reports these devices:
$ cat 00:07/id 00:07/resources # motherboard device
PNP0c02
state = active
io 0x80-0x80
io 0x10-0x1f
io 0x22-0x3f
io 0x44-0x5f
io 0x90-0x9f
io 0xa2-0xbf
io 0x3f0-0x3f1
io 0x3f3-0x3f3
$ cat 00:03/id 00:03/resources # floppy device
PNP0700
state = active
io 0x3f4-0x3f5
io 0x3f2-0x3f2
Reference:
http://lkml.org/lkml/2009/1/31/162
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Reported-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Philippe De Muyter <phdm@macqel.be>
Cc: Adam M Belay <abelay@mit.edu>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I have a Digi Neo 8 PCI card (114f:00b1) Serial controller: Digi
International Digi Neo 8 (rev 05)
that works with the jsm driver after using the following patch.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: Scott H Kilau <Scott_Kilau@digi.com>
Cc: Wendy Xiong <wendyx@us.ibm.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now, early_pfn_in_nid(PFN, NID) may returns false if PFN is a hole.
and memmap initialization was not done. This was a trouble for
sparc boot.
To fix this, the PFN should be initialized and marked as PG_reserved.
This patch changes early_pfn_in_nid() return true if PFN is a hole.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reported-by: David Miller <davem@davemlloft.net>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
What's happening is that the assertion in mm/page_alloc.c:move_freepages()
is triggering:
BUG_ON(page_zone(start_page) != page_zone(end_page));
Once I knew this is what was happening, I added some annotations:
if (unlikely(page_zone(start_page) != page_zone(end_page))) {
printk(KERN_ERR "move_freepages: Bogus zones: "
"start_page[%p] end_page[%p] zone[%p]\n",
start_page, end_page, zone);
printk(KERN_ERR "move_freepages: "
"start_zone[%p] end_zone[%p]\n",
page_zone(start_page), page_zone(end_page));
printk(KERN_ERR "move_freepages: "
"start_pfn[0x%lx] end_pfn[0x%lx]\n",
page_to_pfn(start_page), page_to_pfn(end_page));
printk(KERN_ERR "move_freepages: "
"start_nid[%d] end_nid[%d]\n",
page_to_nid(start_page), page_to_nid(end_page));
...
And here's what I got:
move_freepages: Bogus zones: start_page[2207d0000] end_page[2207dffc0] zone[fffff8103effcb00]
move_freepages: start_zone[fffff8103effcb00] end_zone[fffff8003fffeb00]
move_freepages: start_pfn[0x81f600] end_pfn[0x81f7ff]
move_freepages: start_nid[1] end_nid[0]
My memory layout on this box is:
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x0081ff5d
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] 1: 0x00800000 -> 0x0081f7ff
[ 0.000000] 1: 0x0081f800 -> 0x0081fe50
[ 0.000000] 1: 0x0081fed1 -> 0x0081fed8
[ 0.000000] 1: 0x0081feda -> 0x0081fedb
[ 0.000000] 1: 0x0081fedd -> 0x0081fee5
[ 0.000000] 1: 0x0081fee7 -> 0x0081ff51
[ 0.000000] 1: 0x0081ff59 -> 0x0081ff5d
So it's a block move in that 0x81f600-->0x81f7ff region which triggers
the problem.
This patch:
Declaration of early_pfn_to_nid() is scattered over per-arch include
files, and it seems it's complicated to know when the declaration is used.
I think it makes fix-for-memmap-init not easy.
This patch moves all declaration to include/linux/mm.h
After this,
if !CONFIG_NODES_POPULATES_NODE_MAP && !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use static definition in include/linux/mm.h
else if !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use generic definition in mm/page_alloc.c
else
-> per-arch back end function will be called.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: David Miller <davem@davemlloft.net>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Li Zefan said:
Thread 1:
for ((; ;))
{
mount -t cpuset xxx /mnt > /dev/null 2>&1
cat /mnt/cpus > /dev/null 2>&1
umount /mnt > /dev/null 2>&1
}
Thread 2:
for ((; ;))
{
mount -t cpuset xxx /mnt > /dev/null 2>&1
umount /mnt > /dev/null 2>&1
}
(Note: It is irrelevant which cgroup subsys is used.)
After a while a lockdep warning showed up:
=============================================
[ INFO: possible recursive locking detected ]
2.6.28 #479
---------------------------------------------
mount/13554 is trying to acquire lock:
(&type->s_umount_key#19){--..}, at: [<c049d888>] sget+0x5e/0x321
but task is already holding lock:
(&type->s_umount_key#19){--..}, at: [<c049da0c>] sget+0x1e2/0x321
other info that might help us debug this:
1 lock held by mount/13554:
#0: (&type->s_umount_key#19){--..}, at: [<c049da0c>] sget+0x1e2/0x321
stack backtrace:
Pid: 13554, comm: mount Not tainted 2.6.28-mc #479
Call Trace:
[<c044ad2e>] validate_chain+0x4c6/0xbbd
[<c044ba9b>] __lock_acquire+0x676/0x700
[<c044bb82>] lock_acquire+0x5d/0x7a
[<c049d888>] ? sget+0x5e/0x321
[<c061b9b8>] down_write+0x34/0x50
[<c049d888>] ? sget+0x5e/0x321
[<c049d888>] sget+0x5e/0x321
[<c045a2e7>] ? cgroup_set_super+0x0/0x3e
[<c045959f>] ? cgroup_test_super+0x0/0x2f
[<c045bcea>] cgroup_get_sb+0x98/0x2e7
[<c045cfb6>] cpuset_get_sb+0x4a/0x5f
[<c049dfa4>] vfs_kern_mount+0x40/0x7b
[<c049e02d>] do_kern_mount+0x37/0xbf
[<c04af4a0>] do_mount+0x5c3/0x61a
[<c04addd2>] ? copy_mount_options+0x2c/0x111
[<c04af560>] sys_mount+0x69/0xa0
[<c0403251>] sysenter_do_call+0x12/0x31
The cause is after alloc_super() and then retry, an old entry in list
fs_supers is found, so grab_super(old) is called, but both functions hold
s_umount lock:
struct super_block *sget(...)
{
...
retry:
spin_lock(&sb_lock);
if (test) {
list_for_each_entry(old, &type->fs_supers, s_instances) {
if (!test(old, data))
continue;
if (!grab_super(old)) <--- 2nd: down_write(&old->s_umount);
goto retry;
if (s)
destroy_super(s);
return old;
}
}
if (!s) {
spin_unlock(&sb_lock);
s = alloc_super(type); <--- 1th: down_write(&s->s_umount)
if (!s)
return ERR_PTR(-ENOMEM);
goto retry;
}
...
}
It seems like a false positive, and seems like VFS but not cgroup needs to
be fixed.
Peter said:
We can simply put the new s_umount instance in a but lockdep doesn't
particularly cares about subclass order.
If there's any issue with the callers of sget() assuming the s_umount lock
being of sublcass 0, then there is another annotation we can use to fix
that, but lets not bother with that if this is sufficient.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12673
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Menage <menage@google.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I found a problem of handling of modem status of atmel_serial driver.
With the commit 1ecc26 ("atmel_serial: split the interrupt handler"),
handling of modem status signal was splitted into two parts. The
atmel_tasklet_func() compares new status with irq_status_prev, but
irq_status_prev is not correct if signal status was changed while the port
is closed.
Here is a sequence to cause problem:
1. Remote side sets CTS (and DSR).
2. Local side close the port.
3. Local side clears RTS and DTR.
4. Remote side clears CTS and DSR.
5. Local side reopen the port. hw_stopped becomes 1.
6. Local side sets RTS and DTR.
7. Remote side sets CTS and DSR.
Then CTS change interrupt can be received, but since CTS bit in
irq_status_prev and new status is same, uart_handle_cts_change() will not
be called (so hw_stopped will not be cleared, i.e. cannot send any data).
I suppose irq_status_prev should be initialized at somewhere in open
sequence.
Itai Levi pointed out that we need to initialize atmel_port->irq_status
as well here. His analysis is as follows:
> Regarding the second part of the patch (which resets irq_status_prev),
> it turns out that both versions of the patch (mine and Atsushi's)
> still leave enough room for faulty behavior when opening the port.
>
> This is because we are not resetting both irq_status_prev and
> irq_status in atmel_startup() to CSR, which leads faulty behavior in
> the following sequences:
>
> First case:
> 1. closing the port while CTS line = 1 (TX not allowed)
> 2. setting CTS line = 0 (TX allowed)
> 3. opening the port
> 4. transmitting one char
> 5. Cannot transmit more chars, although CTS line is 0
>
> Second case:
> 1. closing the port while CTS line = 0 (TX allowed)
> 2. setting CTS line = 1 (TX not allowed)
> 3. opening the port
> 4. receiving some chars
> 5. Now we can transmit, although CTS line is 1
>
> This reason for this is that the tasklet is scheduled as a result of
> TX or RX interrupts (not a status change!), in steps 4 above. Inside
> the tasklet, the atmel_port->irq_status (which holds the value from
> the previous session) is compared to atmel_port->irq_status_prev.
> Hence, a status-change of the CTS line is faultily detected.
>
> Both cases were verified on 9260 hardware.
[haavard.skinnemoen@atmel.com: folded with patch from Itai Levi]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Itai Levi <itai.levi.devel@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for HP Pavilion dv5.
Since Intel-based models have an inverted x axis, while AMD-based models
have an inverted y axis, we introduce a new macro that special-cases axis
orientation based on two DMI entries: HP dv5 axis configuration is then
based on both the PRODUCT and BOARD name.
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Tested-by: Palatis Tseng <palatis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sensors responding with 0x3B to WHO_AM_I only have one data register per
direction, thus returning a signed byte from the position which is
occupied by the MSB in sensors responding with 0x3A.
Since multiple sensors share the reply to WHO_AM_I, we rename the defines
to better indicate what they identify (family of single and double
precision sensors).
We support both kind of sensors by checking for the sensor type on init
and defining appropriate data-access routines and sensor limits (for the
joystick) depending on what we find.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Acked-by: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds freefall handling to hp_accel driver. According to HP, it
should just work, without us having to set the chip up by hand.
hpfall.c is example .c program that parks the disk when accelerometer
detects free fall. It should work; for now, it uses fixed 20seconds
protection period.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Otherwise with INPUT=m, EEEPC_LAPTOP=y one gets
drivers/built-in.o: In function `input_sync':
eeepc-laptop.c:(.text+0x18ce51): undefined reference to `input_event'
drivers/built-in.o: In function `input_report_key':
eeepc-laptop.c:(.text+0x18ce73): undefined reference to `input_event'
drivers/built-in.o: In function `eeepc_hotk_check':
eeepc-laptop.c:(.text+0x18d05f): undefined reference to `input_allocate_device'
eeepc-laptop.c:(.text+0x18d10f): undefined reference to `input_register_device'
eeepc-laptop.c:(.text+0x18d131): undefined reference to `input_free_device'
drivers/built-in.o: In function `eeepc_backlight_exit':
eeepc-laptop.c:(.text+0x18d546): undefined reference to `input_unregister_device'
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In cgroup_kill_sb(), root is freed before sb is detached from the list, so
another sget() may find this sb and call cgroup_test_super(), which will
access the root that has been freed.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
YAMAMOTO-san noticed that task_dirty_inc doesn't seem to be called properly for
cases where set_page_dirty is not used to dirty a page (eg. mark_buffer_dirty).
Additionally, there is some inconsistency about when task_dirty_inc is
called. It is used for dirty balancing, however it even gets called for
__set_page_dirty_no_writeback.
So rather than increment it in a set_page_dirty wrapper, move it down to
exactly where the dirty page accounting stats are incremented.
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As requested by Michael, add a missing check for valid flags in
timerfd_settime(), and make it return EINVAL in case some extra bits are
set.
Michael said:
If this is to be any use to userland apps that want to check flag
support (perhaps it is too late already), then the sooner we get it
into the kernel the better: 2.6.29 would be good; earlier stables as
well would be even better.
[akpm@linux-foundation.org: remove unused TFD_FLAGS_SET]
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org> [2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
My @suse.cz address will stop working some day, so put working one into
MAINTAINERS/CREDITS. It would be cool to get this to 2.6.29... it should
not really break anything.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently seq_read assumes that the offset passed to it is always the
offset it passed to user space. In the case pread this assumption is
broken and we do the wrong thing when presented with pread.
To solve this I introduce an offset cache inside of struct seq_file so we
know where our logical file position is. Then in seq_read if we try to
read from another offset we reset our data structures and attempt to go to
the offset user space wanted.
[akpm@linux-foundation.org: restore FMODE_PWRITE]
[pjt@google.com: seq_open needs its fmode opened up to take advantage of this]
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Turner <pjt@google.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Separate FMODE_PREAD and FMODE_PWRITE into separate flags to reflect the
reality that the read and write paths may have independent restrictions.
A git grep verifies that these flags are always cleared together so this
new behavior will only apply to interfaces that change to clear flags
individually.
This is required for "seq_file: properly cope with pread", a post-2.6.25
regression fix.
[akpm@linux-foundation.org: add comment]
Signed-off-by: Paul Turner <pjt@google.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The css_set hash table was introduced in 2.6.26, so update the
documentation accordingly.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Welland ME-747K-SI AoE target generates unsolicited AoE responses that
are marked as vendor extensions. Instead of ignoring these packets, the
aoe driver was generating kernel messages for each unrecognized response
received. This patch corrects the behavior.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Reported-by: <karaluh@karaluh.pl>
Tested-by: <karaluh@karaluh.pl>
Cc: <stable@kernel.org>
Cc: Alex Buell <alex.buell@munted.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have get_vm_area_caller() and __get_vm_area() but not
__get_vm_area_caller()
On powerpc, I use __get_vm_area() to separate the ranges of addresses
given to vmalloc vs. ioremap (various good reasons for that) so in order
to be able to implement the new caller tracking in /proc/vmallocinfo, I
need a "_caller" variant of it.
(akpm: needed for ongoing powerpc development, so merge it early)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the infinite 'while() ;' loops
with a finite loop version.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Timeouts during a command that has a data phase can result in the next
command issued after the command that failed not being processed, i.e. no
interrupt ever occurs to indicate the command has completed. This failure
can result in a deadlock.
This patch resets the data state machine to clear the error in case of a
command timeout.
Tested on OMAP3430 chip and intensive MMC/SD device removal while
transferring data.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Based on a patch from Tony Lindgren ... after initialization,
never change HCTL.SDVS except for MMC1. The other controller
instances only support 1.8V in that field, although they can
suport other card/SDIO/eMMC/... voltages with level shifting
solutions such as external transceivers.
MMC2 behavior sanity tested on Overo/WLAN, OMAP3430 SDP, and
custom hardware. MMC1 also sanity tested on those platforms
plus Beagle. This also fixes a bug preventing MMC2 (and also
presumably MMC3) from powering down when requested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Work around lockdep issue when card detect IRQ handlers run in
thread context ... it forces IRQF_DISABLED, which prevents all
access to twl4030 card detect signals.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Fix the led device naming for the sdhci driver.
The led class documentation defines the led name to have the
form "devicename:colour:function" while not applicable sections
should be left blank.
To comply with the documentation the led device name is changed
from "mmc*" to "mmc*::".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Due to a typo in the Basic Read test, it's currently identical to the
Basic Write test. Fix this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This commit fixes the regression what was added by commit
088a78af978d0c8e339071a9b2bca1f4cb368f30 "s3cmci: Support transfers
which are not multiple of 32 bits."
fifo_free() now returns amount of available space in FIFO buffer in
bytes. But do_pio_write() writes to FIFO 32-bit words. Condition for
return from cycle is (fifo_free() == 0), but when fifo has 1..3 bytes
of free space then this condition will never be true and system hangs.
This patch changes condition in the while() to (fifo_free() > 3).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
blk_abort_queue() iterates the timeout list and aborts each request on the
list, but if the driver error handling readds a request to the timeout list
during this processing, we could be looping forever. Fix this by splicing
current entries to a local list and run over that list instead.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Hi Tejun,
it looks like your commit:
block: don't depend on consecutive minor space
f331c0296f2a9fee0d396a70598b954062603015
broke a particular case for booting from partitioned md/raid devices.
That is the second time this has been broken recently. The previous
time was fixed by
block: do_mounts - accept root=<non-existant partition>
30f2f0eb4bd2c43d10a8b0d872c6e5ad8f31c9a0
Because the data isn't available when an md device is first created
(we add disks and set it up after creation), the initial partition
scan finds nothing. It is not until the device is opened that
another partition scan happens and finds something.
So at the point where the kernel parameter "root=/dev/md_d0p1" is
being parsed, md_d0 exists, but md_d0p1 does not.
However if we let blk_lookup_devt return the correct device number
even though the device doesn't exist, then the attempt to mount it
will successfully find the partition.
I have tried in the past to find a way to get the partition table to
be read as soon as the array is assembled but that proved impossible
(at the time). I don't remember the details, and could possibly
revisit it. However it would be really nice if blk_lookup_devt
could be adjusted to again accept non existant partitions.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
The above commit added WRITE_SYNC and switched various places to using
that for committing writes that will be waited upon immediately after
submission. However, this causes a performance regression with AS and CFQ
for ext3 at least, since sync_dirty_buffer() will submit some writes with
WRITE_SYNC while ext3 has sumitted others dependent writes without the sync
flag set. This causes excessive anticipation/idling in the IO scheduler
because sync and async writes get interleaved, causing a big performance
regression for the below test case (which is meant to simulate sqlite
like behaviour).
---- test case ----
int main(int argc, char **argv)
{
int fdes, i;
FILE *fp;
struct timeval start;
struct timeval end;
struct timeval res;
gettimeofday(&start, NULL);
for (i=0; i<ROWS; i++) {
fp = fopen("test_file", "a");
fprintf(fp, "Some Text Data\n");
fdes = fileno(fp);
fsync(fdes);
fclose(fp);
}
gettimeofday(&end, NULL);
timersub(&end, &start, &res);
fprintf(stdout, "time to write %d lines is %ld(msec)\n", ROWS,
(res.tv_sec*1000000 + res.tv_usec)/1000);
return 0;
}
-------------------
Thanks to Sean.White@APCC.com for tracking down this performance
regression and providing a test case.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
The kexec kernel resets the CCISS hardware in three steps:
1. Use PCI power management states to reset the controller in the
kexec kernel.
2. Clear the MSI/MSI-X bits in PCI configuration space so that MSI
initialization in the kexec kernel doesn't fail.
3. Use the CCISS "No-op" message to determine when the controller
firmware has recovered from the PCI PM reset.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
&&/|| confusion
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
When freeing from bio pool use right ptr to account for bs->front_pad,
instead of bio ptr,
Signed-off-by: Subhash Peddamallu <subhash.peddamallu@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
We can't OR shift values, so get rid of BIO_RW_SYNC and use BIO_RW_SYNCIO
and BIO_RW_UNPLUG explicitly. This brings back the behaviour from before
213d9417fec62ef4c3675621b9364a667954d4dd.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
When submitting requests via SG_IO, which does a sync io, a
bsg_command is not allocated. So an in-Kernel sense_buffer was not
set. However when calling blk_execute_rq() with no sense buffer
one is provided from the stack. Now bsg at blk_complete_sgv4_hdr_rq()
would check if rq->sense_len and a sense was requested by sg_io_v4
the rq->sense was copy_user() back, but by now it is already mangled
stack memory.
I have fixed that by forcing a sense_buffer when calling bsg_map_hdr().
The bsg_command->sense is provided in the write/read path like before,
and on-the-stack buffer is provided when doing SG_IO.
I have also fixed a dprintk message to print rq->errors in hex because
of the scsi bit-field use of this member. For other block devices it
does not matter anyway.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This reverts commit a4b76193774b463b922cab2f92450efb20d29ef0.
It turned out that the controller had problem running at the
higher speed, so go back to trusting the hardware capability
bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
