Age | Commit message (Collapse) | Author |
|
If the microcode driver is built in (rather than module) there are some,
ehm, interesting effects happening due to the new "call out to userspace"
behavior that is introduced.. and which runs too early. The result is a
boot hang; which is really nasty.
The patch below is a minimally safe patch to fix this regression for 2.6.19
by just not requesting actual microcode updates during early boot. (That
is a good idea in general anyway)
The "real" fix is a lot more complex given the entire cpu hotplug scenario
(during cpu hotplug you normally need to load the microcode as well); but
the interactions for that are just really messy at this point; this fix at
least makes it work and avoids a full detangle of hotplug.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* merom:v2.6/linux:
x86-64: write IO APIC irq routing entries in correct order
x86-64: clean up io-apic accesses
|
|
This is the x86-64 version of f9dadfa71bc594df09044da61d1c72701121d802
that did the same thing on i386.
Since the "mask" bit is in the low word, when we write a new entry, we
need to write the high word first, before we potentially unmask it.
The exception is when we actually want to mask the interrupt, in which
case we want to write the low word first to make sure that the high word
doesn't change while the interrupt routing is still active.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This is just commit 130fe05dbc0114609cfef9815c0c5580b42decfa ported to
x86-64, for all the same reasons. It cleans up the IO-APIC accesses in
order to then fix the ordering issues.
We move the accessor functions (that were only used by io_apic.c) out of
a header file, and use proper memory-mapped accesses rather than making
up our own "volatile" pointers.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This reverts commit de09bddb9d6f96785be470c832b881e6d72d589f. It tried
to reserve the MMCONFIG mmio memory ranges, but since the MMCONFIG
information is broken and often bogus (which is why we don't dare use it
most of the time _anyway_), it does more harm than good.
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] sata_via: fix obvious typo
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[DECNET]: Endianess fixes (try #2)
[TG3]: Fix array overrun in tg3_read_partno().
[NET]: Set truesize in pskb_copy
[NETPOLL]: Compute checksum properly in netpoll_send_udp().
[PKT_SCHED] sch_htb: Use hlist_del_init().
[TCP]: Don't use highmem in tcp hash size calculation.
[NET]: kconfig, correct traffic shaper
|
|
Spotted by Martin Devera.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Ok, things are clearly starting to calm down.. Finally.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbglaw/vax-linux
* 'fixes_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbglaw/vax-linux:
Update for the srm_env driver.
|
|
Here are some fixes to endianess problems spotted by Al Viro.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use proper upper limits for the loops and check for all error
conditions.
The problem was noticed by Adrian Bunk.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since pskb_copy tacks on the non-linear bits from the original
skb, it needs to count them in the truesize field of the new skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise we can hit paths that (legally) do multiple deletes on the
same node and OOPS with the HLIST poison values there instead of
NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes consideration of high memory when determining TCP
hash table sizes. Taking into account high memory results in tcp_mem
values that are too large.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Patrick McHardy <kaber@trash.net> suggested, Traffic Shaper is now
obsolete and alternative to it is no longer CBQ, since its problems with
virtual devices, alter Kconfig text to reflect this -- put a link to the
traffic schedulers as a whole.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3927/1: Allow show_mem() to work with holes in memory map.
[ARM] 3926/1: make timer led handle HZ != 100
[ARM] 3923/1: S3C24XX: update s3c2410_defconfig with new drivers
[ARM] 3922/1: S3C24XX: update s3c2410_defconfig to 2.6.19-rc4
[ARM] 3921/1: S3C24XX: remove bast_defconfig
[ARM] 3920/1: S3C24XX: Remove smdk2410_defconfig
[ARM] 3919/1: Fixed definition of some PXA270 CIF related registers
[ARM] 3918/1: ixp4xx irq-chip rework
[ARM] 3912/1: Make PXA270 advertise HWCAP_IWMMXT capability
[ARM] 3915/1: S3C2412: Add s3c2410_gpio_getirq() to general gpio.c
[ARM] 3917/1: Fix dmabounce symbol exports
|
|
This patch contains a fix for a bug introduced more than a year ago
(not setting *eof) and updates whitespace a bit.
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
|
|
show_mem() was not correctly handling holes in the memory
map. It was treating the freed sections of the map as
though they contained valid struct page entries. This
could cause incorrect debugging output or even a kernel
panic.
This patch keeps the struct meminfo around after system
initialization so that show_mem() can use it when
scanning memory. show_mem() now walks over each bank
of each online node, rather than assuming that each node
contains a single contiguous bank.
Signed-off-by: Ray Lehtiniemi <rayl@mail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The timer LED is unusable at HZ=large, since it's got
a hard-wired value of 100 ticks per cycle; when HZ=1024
(for example) it's essentially always-on. This patch
just makes that be HZ ticks per cycle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
e1000: Fix suspend/resume powerup and irq allocation
From: Auke Kok <auke-jan.h.kok@intel.com>
After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.
Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Through some experimentation with the similarly built bcm43xx I came to
the conclusion that if the hw/firmware sets a bit in the interrupt
register, an interrupt will only be raised if that bit is included in
the interrupt mask. Hence, the interrupt mask is more like an interrupt
control mask.
This patch changes the comment to reflect that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix EV64120 and Ocelot builds by providing a plat_timer_setup().
[MIPS] EV64120: Fix PCI interrupt allocation.
[MIPS] Make irq number allocator generally available for fixing EV64120.
[MIPS] EV64120: Fix timer initialization for HZ != 100.
[MIPS] Ocelot 3: Fix MAC address detection after platform_device conversion.
[MIPS] Ocelot C: Fix MAC address detection after platform_device conversion.
[MIPS] SB1: On bootup only flush cache on local CPU.
[MIPS] Ocelot 3: Fix large number of warnings.
[MIPS] Ocelot C: Fix mapping of ioport address range.
[MIPS] Ocelot C: Fix warning about missmatching format string.
[MIPS] Ocelot C: fix eth registration after conversion to platform_device
[MIPS] Ocelot C: Fix large number of warnings.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4751): Fix DBV_FE_CUSTOMISE for card drivers compiled into kernel
V4L/DVB (4784): [saa7146_i2c] short_delay mode fixed for fast machines
V4L/DVB (4770): Fix mode switch of Compro Videomate T300
V4L/DVB (4787): Budget-ci: Inversion setting fixed for Technotrend 1500 T
V4L/DVB (4786): Pvrusb2: use NULL instead of 0
V4L/DVB (4785): Budget-ci: Change DEBIADDR_IR to a safer default
V4L/DVB (4752): DVB: Add DVB_FE_CUSTOMISE support for MT2060
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This fixes a warning on bootup warning in smp_call_function.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
o Fix warnings
o 768MB worth of I/O ports were insane
o 64-bit kernels don't need special handling because ioremap does the magic
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CC arch/mips/momentum/ocelot_c/setup.o
arch/mips/momentum/ocelot_c/setup.c: In function 'momenco_time_init':
arch/mips/momentum/ocelot_c/setup.c:223: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
Change data type to match format string; a 32-bit type better suits our
needs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
[DLM] fix oops in kref_put when removing a lockspace
[DLM] Fix kref_put oops
[GFS2] Fix OOM error handling
[GFS2] Fix incorrect fs sync behaviour.
[GFS2] don't panic needlessly
|
|
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
AVR32: Add missing return instruction in __raw_writesb
AVR32: Wire up sys_epoll_pwait
AVR32: Fix thinko in generic_find_next_zero_le_bit()
AVR32: Get rid of board_early_init
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] IRQs too early enabled.
[S390] revert add_active_range() usage patch.
|
|
Now that the lockspace struct is freed when the last sysfs object is released
this patch prevents use of that lockspace by sysfs. We attempt to re-get the
lockspace from the lockspace list and fail the request if it has been removed.
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
This patch fixes the recounting on the lockspace kobject. Previously the lockspace was freed while userspace could have had a
reference to one of its sysfs files, causing an oops in kref_put.
Now the lockspace kfree is moved into the kobject release() function
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Fix the OOM error handling in inode.c where it was possible for
a NULL pointer to be dereferenced.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
This adds a sync_fs superblock operation for GFS2 and removes
the journal flush from write_super in favour of sync_fs where it
ought to be. This is more or less identical to the way in which ext3
does this.
This bug was pointed out by Russell Cattelan <cattelan@redhat.com>
Cc: Russell Cattelan <cattelan@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
First, SLAB_PANIC is unjustified. Second, all error propagating and backing out
is in place.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
__raw_writesb ends with a conditional branch, which is obviously
wrong. It should return after the last loop terminates.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
setup_lowcore() calls ctl_set_bit() which returns withs interrupts
enabled. The setup arch code is not supposed to enable interrupts that
early. Therefore use the __ctl_set_bit() variant.
This fixes the not working lock dependency validator on non 64 bit
systems.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Commit 7676bef9c183fd573822cac9992927ef596d584c breaks DCSS support on
s390. DCSS needs initialized struct pages to work. With the usage of
add_active_range() only the struct pages for physically present pages
are initialized.
This could be fixed if the DCSS driver would initiliaze the struct pages
itself, but this doesn't work too. This is because the mem_map array
does not include holes after the last present memory area and therefore
there is nothing that could be initialized.
To fix this and to avoid some dirty hacks revert this patch for now.
Will be added later when we move to a virtual mem_map.
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Kconfig: remove redundant NETDEVICES depends
[PATCH] ehea: 64K page support fix
[PATCH] ehea: Removed redundant define
[PATCH] ehea: Nullpointer dereferencation fix
[PATCH] bcm43xx: fix unexpected LED control values in BCM4303 sprom
[PATCH] bcm43xx: Fix low-traffic netdev watchdog TX timeouts
[PATCH] hostap_plx: fix CIS verification
[PATCH] ieee80211: don't flood log with errors
|