| Age | Commit message (Collapse) | Author |
|---|
|
Add checksum default defines for mobility header(MH) which
goes through raw socket. As the result kernel's behavior is
to handle MH checksum as default.
This patch also removes verifying inbound MH checksum at
mip6_mh_filter() since it did not consider user specified
checksum offset and was redundant check with raw socket code.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add_grhead() allocates memory with GFP_ATOMIC and in at least two places skb
from it passed to skb_put() without checking.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we can't find the afinfo we should return EAFNOSUPPORT.
GCC warned about the uninitialized 'err' for this path as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the patch to support IPv4 over IPv6 IPsec.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the patch to support IPv6 over IPv4 IPsec
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch exports xfrm_state_afinfo.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
calls
Replace kmalloc() + memset() pairs with the appropriate kzalloc() calls in
the bonding driver.
Signed-off-by: Joe Jin <lkmaillist@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
During an oprofile session of linux-2.6.20 on a dual opteron system, I noticed
an expensive divide was done in tg3_poll().
I am using gcc-4.1.1, so the following comment from drivers/net/tg3.c seems
over-optimistic :
/* Do not place this n-ring entries value into the tp struct itself,
* we really want to expose these constants to GCC so that modulo et
* al. operations are done with shifts and masks instead of with
* hw multiply/modulo instructions. Another solution would be to
* replace things like '% foo' with '& (foo - 1)'.
*/
#define TG3_RX_RCB_RING_SIZE(tp) \
((tp->tg3_flags2 & TG3_FLG2_5705_PLUS) ? 512 : 1024)
Assembly code before patch :
(oprofile results included)
6434 0.0088 :ffffffff803684b9: mov 0x6f0(%r15),%eax
587 8.0e-04 :ffffffff803684c0: and $0x40000,%eax
2170 0.0030 :ffffffff803684c5: cmp $0x1,%eax
:ffffffff803684c8: lea 0x1(%r13),%eax
:ffffffff803684cc: sbb %ecx,%ecx
2051 0.0028 :ffffffff803684ce: xor %edx,%edx
:ffffffff803684d0: and $0x200,%ecx
20 2.7e-05 :ffffffff803684d6: add $0x200,%ecx
1986 0.0027 :ffffffff803684dc: div %ecx
103427 0.1410 :ffffffff803684de: cmp %edx,0xffffffffffffff7c(%rbp)
Assembly code after the suggested patch :
ffffffff803684b9: mov 0x6f0(%r15),%eax
ffffffff803684c0: and $0x40000,%eax
ffffffff803684c5: cmp $0x1,%eax
ffffffff803684c8: sbb %eax,%eax
ffffffff803684ca: inc %r13d
ffffffff803684cd: and $0x200,%eax
ffffffff803684d2: add $0x1ff,%eax
ffffffff803684d7: and %eax,%r13d
ffffffff803684da: cmp %r13d,0xffffffffffffff7c(%rbp)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/dccp/ccids/ccid3.c: In function `ccid3_hc_rx_packet_recv':
net/dccp/ccids/ccid3.c:1007: warning: long int format, different type arg (arg 3)
net/dccp/ccids/ccid3.c:1007: warning: long int format, different type arg (arg 4)
opaque types must be suitably cast for printing.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kzalloc() calls
This patch replace kmalloc() + memset() pairs with the appropriate
kzalloc().
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch contains the following cleanups:
- make the following needlessly global functions static:
- lock_adapter_irq()
- unlock_adapter_irq()
- #if 0 the following unused global functions:
- wanrouter_encapsulate()
- wanrouter_type_trans()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was reported by Ingo Molnar here,
http://lkml.org/lkml/2006/12/18/119
The problem is that adummy_init() depends on atm_init() , but adummy_init()
is called first.
So I put atm_init() into subsys_initcall which seems appropriate, and it
will still get module_init() if it becomes a module.
Interesting to note that you could crash your system here if you just load
the modules in the wrong order.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces users of the round_jiffies() function in the
networking code.
These timers all were of the "about once a second" or "about once
every X seconds" variety and several showed up in the "what wakes the
cpu up" profiles that the tickless patches provide. Some timers are
highly dynamic based on network load; but even on low activity systems
they still show up so the rounding is done only in cases of low
activity, allowing higher frequency timers in the high activity case.
The various hardware watchdogs are an obvious case; they run every 2
seconds but aren't otherwise specific of exactly when they need to
run.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We clear the unused parts of the SACK cache, This prevents us from mistakenly
taking the cache data if the old data in the SACK cache is the same as the data
in the SACK block. This assumes that we never receive an empty SACK block with
start and end both at zero.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move DSACK code outside the SACK fast-path checking code. If the DSACK
determined that the information was too old we stayed with a partial cache
copied. Most likely this matters very little since the next packet will not be
DSACK and we will find it in the cache. but it's still not good form and there
is little reason to couple the two checks.
Since the SACK receive cache doesn't need the data to be in host order we also
remove the ntohl in the checking loop.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only advance the SACK fast-path pointer for the first block, the
fast-path assumes that only the first block advances next time so we
should not move the cached skb for the next sack blocks.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both aux data and sockaddr tries to use the same buffer which
obviously doesn't work. We just happen to have 4 bytes free in
the skb->cb if you take away the maximum length of sockaddr_ll.
That's just enough to store the one piece of info from aux data
that we can't generate at recvmsg(2) time.
This is what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is needed to make ISC's DHCP server (and probably other
DHCP servers/clients using AF_PACKET) to be able to serve another
client on the same Xen host.
The problem is that packets between different domains on the same
Xen host only have partial checksums. Unfortunately this piece of
information is not passed along in AF_PACKET unless you're using
the mmap interface. Since dhcpd doesn't support packet-mmap, UDP
packets from the same host come out with apparently bogus checksums.
This patch adds a mechanism for AF_PACKET recvmsg(2) to return the
status along with the packet. It does so by adding a new cmsg that
contains this information along with some other relevant data such
as the original packet length.
I didn't include the time stamp information since there is already
a cmsg for that.
This patch also changes the mmap code to set the CSUMNOTREADY flag
on all packets instead of just outoing packets on cooked sockets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do this even for non-blocking sockets. This avoids the silly -EAGAIN
that applications can see now, even for non-blocking sockets in some
cases (f.e. connect()).
With help from Venkat Tekkirala.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tcphdr struct passed to tcp_v4_check is not used, the following
patch removes it from the parameter list.
This adds the netfilter modifications missing in the patch I sent
for rc3-mm1.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With help from Wei Dong <weid@np.css.fujitsu.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently netlink users BUG when the allocated skb for an event
notification is undersized. While this is certainly a kernel bug,
its not critical and crashing the kernel is too drastic, especially
when considering that these errors have appeared multiple times in
the past and it BUGs even if no listeners are present.
This patch replaces BUG by WARN_ON and changes the notification
functions to inform potential listeners of undersized allocations
using a unique error code (EMSGSIZE).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a dump_stats callback to enable
printing of basic statistics of prio classes.
(With help of Patrick McHardy).
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/mfasheh/ocfs2: (22 commits)
configfs: Zero terminate data in configfs attribute writes.
[PATCH] ocfs2 heartbeat: clean up bio submission code
ocfs2: introduce sc->sc_send_lock to protect outbound outbound messages
[PATCH] ocfs2: drop INET from Kconfig, not needed
ocfs2_dlm: Add timeout to dlm join domain
ocfs2_dlm: Silence some messages during join domain
ocfs2_dlm: disallow a domain join if node maps mismatch
ocfs2_dlm: Ensure correct ordering of set/clear refmap bit on lockres
ocfs2: Binds listener to the configured ip address
ocfs2_dlm: Calling post handler function in assert master handler
ocfs2: Added post handler callable function in o2net message handler
ocfs2_dlm: Cookies in locks not being printed correctly in error messages
ocfs2_dlm: Silence a failed convert
ocfs2_dlm: wake up sleepers on the lockres waitqueue
ocfs2_dlm: Dlm dispatch was stopping too early
ocfs2_dlm: Drop inflight refmap even if no locks found on the lockres
ocfs2_dlm: Flush dlm workqueue before starting to migrate
ocfs2_dlm: Fix migrate lockres handler queue scanning
ocfs2_dlm: Make dlmunlock() wait for migration to complete
ocfs2_dlm: Fixes race between migrate and dirty
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
Revert "Driver core: convert SPI code to use struct device"
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (116 commits)
[POWERPC] Add export of vgacon_remap_base
[POWERPC] Remove bogus comment about page_is_ram
[POWERPC] windfarm: don't die on suspend thread signal
[POWERPC] Fix comment in kernel/irq.c
[POWERPC] ppc: Fix booke watchdog initialization
[POWERPC] PPC: Use ARRAY_SIZE macro when appropriate
[POWERPC] Use ARRAY_SIZE macro when appropriate
[POWERPC] Fix ppc64's writing to struct file_operations
[POWERPC] ppc: use syslog macro for the printk log level
[POWERPC] ppc: cs4218_tdm remove extra brace
[POWERPC] Add mpc52xx/lite5200 PCI support
[POWERPC] Only use H_BULK_REMOVE if the firmware supports it
[POWERPC] Fixup error handling when emulating a floating point instruction
[POWERPC] Enable interrupts if we are doing fp math emulation
[POWERPC] Added kprobes support to ppc32
[POWERPC] Make pSeries use the H_BULK_REMOVE hypervisor call
[POWERPC] Clear RI bit in MSR before restoring r13 when returning to userspace
[POWERPC] Fix performance monitor exception
[POWERPC] Compile fixes for arch/powerpc dcr code
[POWERPC] Maple: use mmio nvram
...
|
|
master.kernel.org:/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of master.kernel.org:/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Allow for 44 bit user-tokens (or drm_file offsets)
drm/via: Disable AGP DMA for chips with the new 3D engine.
drm: update core memory manager from git drm tree
drm: remove drm_ioremap and drm_ioremapfree
i810/i830: use drm_core_ioremap instead of drm_ioremap
drm: use vmalloc_user instead of vmalloc_32 for DRM_SHM
via: allow for npot texture pitch alignment
via: add some new chipsets
via: some PCI posting flushes
|
|
Michal Ostrowski points out what the real problem was: the spaces at the
start of the definition of the 'checker-shell' make function.
Cc: Michal Ostrowski <mostrows@watson.ibm.com>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Oleg Verych <olecom@flower.upol.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 2943ecf2ed32632473c06f1975db47a7aa98c10f.
This should go through the SPI maintainer, it was my fault that it did
not. Especially as it conflicts with other patches he has pending.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
The following macro :
include/asm-powerpc/vga.h:#define VGA_MAP_MEM(x,s) (x + vgacon_remap_base)
is used by drivers/video/console/vgacon.c which can be compiled as a module
(drivers/video/vga16fb.ko).
Therefore, vgacon_remap_base should be exported.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
arch/powerpc/mm/mem.c states that page_is_ram is called by the code that
implements /dev/mem, which isn't true. Remove the comment.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
When the windfarm thread gets a suspend signal it will die instead of
freezing. This fixes it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
kernel/irq.c contains a comment that speaks of -1 and -2 as interrupt
numbers, but this is actually dependent on configuration options now.
Replace by NO_IRQ and NO_IRQ_ENABLED.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Fix two problems in the book-e watchdog driver.
a) The 4xx default period was defined wrong
b) Clear status before enabling the watchdog exception
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
In preparation for marking file_operations as const.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Use the appropriate logging macro for the priority level for that
printk call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
It looks like GNU make version 3.80 (but apparently not 3.81) adds
leading whitespace to the result of the checker-shell execution. This
strips them off explicitly.
Also, don't bother symlinking the output file to /dev/null. It's likely
as expensive as just writing the temp-file, and we need to remove it
anyway afterwards.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into for-2.6.21
|
|
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6: (23 commits)
ide-acpi support warning fix
ACPI support for IDE devices
IDE Driver for Delkin/Lexar/etc.. cardbus CF adapter
ide: it8213 IDE driver update (version 2)
ide: add it8213 IDE driver
tc86c001: add missing __init tag for tc86c001_ide_init()
tc86c001: mark init_chipset_tc86c001() with __devinit tag
tc86c001: init_hwif_tc86c001() can be static
ide: add Toshiba TC86C001 IDE driver (take 2)
pdc202xx_new: remove check_in_drive_lists abomination
pdc202xx_new: remove useless code
slc90e66: carry over fixes from piix driver
piix: tuneproc() fixes/cleanups
piix: fix 82371MX enablebits
hpt366: HPT36x PCI clock detection fix
hpt366: init code rewrite
hpt366: clean up DMA timeout handling for HPT370
hpt366: merge HPT37x speedproc handlers
hpt366: cache channel's MCR address
hpt366: switch to using pci_get_slot
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (41 commits)
Revert "PCI: remove duplicate device id from ata_piix"
msi: Make MSI useable more architectures
msi: Kill the msi_desc array.
msi: Remove attach_msi_entry.
msi: Fix msi_remove_pci_irq_vectors.
msi: Remove msi_lock.
msi: Kill msi_lookup_irq
MSI: Combine pci_(save|restore)_msi/msix_state
MSI: Remove pci_scan_msi_device()
MSI: Replace pci_msi_quirk with calls to pci_no_msi()
PCI: remove duplicate device id from ipr
PCI: remove duplicate device id from ata_piix
PCI: power management: remove noise on non-manageable hw
PCI: cleanup MSI code
PCI: make isa_bridge Alpha-only
PCI: remove quirk_sis_96x_compatible()
PCI: Speed up the Intel SMBus unhiding quirk
PCI Quirk: 1k I/O space IOBL_ADR fix on P64H2
shpchp: delete trailing whitespace
shpchp: remove DBG_XXX_ROUTINE
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (70 commits)
USB: remove duplicate device id from zc0301
USB: remove duplicate device id from usb_storage
USB: remove duplicate device id from keyspan
USB: remove duplicate device id from ftdi_sio
USB: remove duplicate device id from visor
USB: a bit more coding style cleanup
usbcore: trivial whitespace fixes
usb-storage: use first bulk endpoints, not last
EHCI: fix interrupt-driven remote wakeup
USB: switch ehci-hcd to new polling scheme
USB: autosuspend for usb printer driver
USB Input: Added kernel module to support all GTCO CalComp USB InterWrite School products
USB: Sierra Wireless auto set D0
USB: usb ethernet gadget recognizes HUSB2DEV
USB: list atmel husb2_udc gadget controller
USB: gadgetfs AIO tweaks
USB: gadgetfs behaves better on userspace init bug
USB: gadgetfs race fix
USB: gadgetfs simplifications
USB: gadgetfs cleanups
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (28 commits)
sysfs: Shadow directory support
Driver Core: Increase the default timeout value of the firmware subsystem
Driver core: allow to delay the uevent at device creation time
Driver core: add device_type to struct device
Driver core: add uevent vars for devices of a class
SYSFS: Fix missing include of list.h in sysfs.h
HOWTO: Add a reference to Harbison and Steele
sysfs: error handling in sysfs, fill_read_buffer()
kobject: kobject_put cleanup
sysfs: kobject_put cleanup
sysfs: suppress lockdep warnings
Driver core: fix race in sysfs between sysfs_remove_file() and read()/write()
driver core: Change function call order in device_bind_driver().
driver core: Don't stop probing on ->probe errors.
driver core fixes: device_register() retval check in platform.c
driver core fixes: make_class_name() retval checks
/sys/modules/*/holders
USB: add the sysfs driver name to all modules
SERIO: add the sysfs driver name to all modules
PCI: add the sysfs driver name to all modules
...
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (116 commits)
sk98lin: planned removal
AT91: MACB support
sky2: version 1.12
sky2: add new chip ids
sky2: Yukon Extreme support
sky2: safer transmit timeout
sky2: TSO support for EC_U
sky2: use dev_err for error reports
sky2: add Wake On Lan support
fix unaligned exception in /drivers/net/wireless/orinoco.c
Remove unused kernel config option DLCI_COUNT
z85230: spinlock logic
mips: declance: Driver model for the PMAD-A
Spidernet: Rework RX linked list
NET: turn local_save_flags() + local_irq_disable() into local_irq_save()
NET-3c59x: turn local_save_flags() + local_irq_disable() into local_irq_save()
hp100: convert pci_module_init() to pci_register_driver()
NetXen: Added ethtool support for user level tools.
NetXen: Firmware crb init changes.
maintainers: add atl1 maintainers
...
|
