| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
On my machine with gcc 3.4, kvm uses ~2k of stack in a few
select functions. This is mostly because gcc fails to
notice that the different case: statements could have their
stack usage combined. It overflows very nicely if interrupts
happen during one of these large uses.
This patch uses two methods for reducing stack usage.
1. dynamically allocate large objects instead of putting
on the stack.
2. Use a union{} member for all of the case variables. This
tricks gcc into combining them all into a single stack
allocation. (There's also a comment on this)
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Based on a patch from: Amit Shah <amit.shah@qumranet.com>
This patch adds support for handling PCI devices that are assigned to
the guest.
The device to be assigned to the guest is registered in the host kernel
and interrupt delivery is handled. If a device is already assigned, or
the device driver for it is still loaded on the host, the device
assignment is failed by conveying a -EBUSY reply to the userspace.
Devices that share their interrupt line are not supported at the moment.
By itself, this patch will not make devices work within the guest.
The VT-d extension is required to enable the device to perform DMA.
Another alternative is PVDMA.
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Ben-Ami Yassour <benami@il.ibm.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Userspace may specify memory slots that are backed by mmio pages rather than
normal RAM. In some cases it is not enough to identify these mmio pages
by pfn_valid(). This patch adds checking the PageReserved as well.
Signed-off-by: Ben-Ami Yassour <benami@il.ibm.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
We're currently facing timing problems in guests that do
calibration under heavy load, and then the load vanishes.
This means we'll have a much lower lpj than we actually should,
and delays end up taking less time than they should, which is a
nasty bug.
Solution is to pass on the lpj value from host to guest, and have it
preset.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
KVM intends to use paravirt code to calibrate khz. Xen
current code will do just fine. So as a first step, factor out
code to pvclock.c.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
The PIT injection logic is problematic under the following cases:
1) If there is a higher priority vector to be delivered by the time
kvm_pit_timer_intr_post is invoked ps->inject_pending won't be set.
This opens the possibility for missing many PIT event injections (say if
guest executes hlt at this point).
2) ps->inject_pending is racy with more than two vcpus. Since there's no locking
around read/dec of pt->pending, two vcpu's can inject two interrupts for a single
pt->pending count.
Fix 1 by using an irq ack notifier: only reinject when the previous irq
has been acked. Fix 2 with appropriate locking around manipulation of
pending count and irq_ack by the injection / ack paths.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Based on a patch from: Ben-Ami Yassour <benami@il.ibm.com>
which was based on a patch from: Amit Shah <amit.shah@qumranet.com>
Notify IRQ acking on PIC/APIC emulation. The previous patch missed two things:
- Edge triggered interrupts on IOAPIC
- PIC reset with IRR/ISR set should be equivalent to ack (LAPIC probably
needs something similar).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
CC: Amit Shah <amit.shah@qumranet.com>
CC: Ben-Ami Yassour <benami@il.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
This can be used by kvm subsystems that are interested in when
interrupts are acked, for example time drift compensation.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
When we use TID=N userspace mappings, we must ensure that kernel mappings have
been destroyed when entering userspace. Using TID=1/TID=0 for kernel/user
mappings and running userspace with PID=0 means that userspace can't access the
kernel mappings, but the kernel can directly access userspace.
The net is that we don't need to flush the TLB on privilege switches, but we do
on guest context switches (which are far more infrequent). Guest boot time
performance improvement: about 30%.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Track which TLB entries need to be written, instead of overwriting everything
below the high water mark. Typically only a single guest TLB entry will be
modified in a single exit.
Guest boot time performance improvement: about 15%.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
We're saving the host TLB state to memory on every exit, but never using it.
Originally I had thought that we'd want to restore host TLB for heavyweight
exits, but that could actually hurt when context switching to an unrelated host
process (i.e. not qemu).
Since this decreases the performance penalty of all exits, this patch improves
guest boot time by about 15%.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Allow host userspace to program hardware debug registers to set breakpoints
inside guests.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Netware writes to DEBUGCTL and reads from the DEBUGCTL and LAST*IP MSRs
without further checks and is really confused to receive a #GP during that.
To make it happy we should just make them stubs, which is exactly what SVM
already does.
Writes to DEBUGCTL that are vendor-specific are resembled to behave as if the
virtual CPU does not know them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Usually HOST_RSP retains its value across guest entries. Take advantage
of this and avoid a vmwrite() when this is so.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
This patch adds a trace point for the instruction emulation on embedded powerpc
utilizing the KVM_TRACE interface.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
This patch adds trace points to track powerpc TLB activities using the
KVM_TRACE infrastructure.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
This patch enables KVM_TRACE to build for PowerPC arch. This means just
adding sections to Kconfig and Makefile.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
The current kvmtrace code uses get_cycles() while the interpretation would be
easier using using nanoseconds. ktime_get() should give at least the same
accuracy as get_cycles on all architectures (even better on 32bit archs) but
at a better unit (e.g. comparable between hosts with different frequencies.
[avi: avoid ktime_t in public header]
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
This patch fixes kvmtrace use on big endian systems. When using bit fields the
compiler will lay data out in the wrong order expected when laid down into a
file.
This fixes it by using one variable instead of using bit fields.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
As we execute real mode guests in VM86 mode, exception have to be
reinjected appropriately when the guest triggered them. For this purpose
the patch adopts the real-mode injection pattern used in vmx_inject_irq
to vmx_queue_exception, additionally taking care that the IP is set
correctly for #BP exceptions. Furthermore it extends
handle_rmode_exception to reinject all those exceptions that can be
raised in real mode.
This fixes the execution of himem.exe from FreeDOS and also makes its
debug.com work properly.
Note that guest debugging in real mode is broken now. This has to be
fixed by the scheduled debugging infrastructure rework (will be done
once base patches for QEMU have been accepted).
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Since checking for vcpu->arch.rmode.active is already done whenever we
call handle_rmode_exception(), checking it inside the function is redundant.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Instead of looking at failed injections in the vm entry path, move
processing to the exit path in vmx_complete_interrupts(). This simplifes
the logic and removes any state that is hidden in vmx registers.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Similar to the exception queue, this hold interrupts that have been
accepted by the virtual processor core but not yet injected.
Not yet used.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
The vmx code assumes that IDT-Vectoring can only be set when an exception
is injected due to the exception in question. That's not true, however:
if the exception is injected correctly, and later another exception occurs
but its delivery is blocked due to a fault, then we will incorrectly assume
the first exception was not delivered.
Fix by unconditionally dequeuing the pending exception, and requeuing it
(or the second exception) if we see it in the IDT-Vectoring field.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
If we're emulating an instruction, either it will succeed, in which case
any previously queued exception will be spurious, or we will requeue the
same exception.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Instead of processing nmi injection failure in the vm entry path, move
it to the vm exit path (vm_complete_interrupts()). This separates nmi
injection from nmi post-processing, and moves the nmi state from the VT
state into vcpu state (new variable nmi_injected specifying an injection
in progress).
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Currently most interrupt exit processing is handled on the entry path,
which is confusing. Move the NMI IRET fault processing to a new function,
vmx_complete_interrupts(), which is called on the vmexit path.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
The twisty maze of conditionals can be reduced.
[joerg: fix tlb flushing]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Place into own function, in preparation for further cleanups.
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
This function injects an interrupt into the guest given the kvm struct,
the (guest) irq number and the interrupt level.
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
Move KVM trace definitions from x86 specific kvm headers to common kvm
headers to create a cross-architecture numbering scheme for trace
events. This means the kvmtrace_format userspace tool won't need to know
which architecture produced the log file being processed.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
As suggested by Avi, introduce accessors to read/write guest registers.
This simplifies the ->cache_regs/->decache_regs interface, and improves
register caching which is important for VMX, where the cost of
vmcs_read/vmcs_write is significant.
[avi: fix warnings]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
MSR_IA32_FEATURE_LOCKED is just a bit in fact, which shouldn't be prefixed with
MSR_. So is MSR_IA32_FEATURE_VMXON_ENABLED.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
|
|
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-viapro: Add support for SMBus Process Call transactions
i2c: Restore i2c_smbus_process_call function
i2c: Do earlier driver model init
i2c: Only build Tyan SMBus mux drivers on x86
i2c: Guard against oopses from bad init sequences
i2c: Document the implementation details of the /dev interface
i2c: Improve dev-interface documentation
i2c-parport-light: Don't register a platform device resource
hwmon: (dme1737) Convert to a new-style i2c driver
hwmon: (dme1737) Be less i2c-centric
i2c/tps65010: Vibrator hookup to gpiolib
i2c-viapro: Add VX800/VX820 support
i2c: Renesas Highlander FPGA SMBus support
i2c-pca-isa: Don't grab arbitrary resources
i2c/isp1301_omap: Convert to a new-style i2c driver, part 2
i2c/isp1301_omap: Convert to a new-style i2c driver, part 1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: build drivers for all quirky devices by default
HID: add missing blacklist entry for Apple ATV ircontrol
HID: add support for Bright ABNT2 brazilian device
HID: Don't let Avermedia Radio FM800 be handled by usb hid drivers
HID: fix numlock led on Dell device 0x413c/0x2105
HID: remove warn() macro from usb hid drivers
HID: remove info() macro from usb HID drivers
HID: add appletv IR receiver quirk
HID: fix a lockup regression when using force feedback on a PID device
HID: hiddev.h: Fix example code.
HID: hiddev.h: Fix mixed space and tabs in example code.
HID: convert to dev_* prints
HID: remove hid-ff
HID: move zeroplus FF processing
HID: move thrustmaster FF processing
HID: move pantherlord FF processing
HID: fix incorrent length condition in hidraw_write()
HID: fix tty<->hid deadlock
HID: ignore iBuddy devices
HID: report descriptor fix for remaining MacBook JIS keyboards
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (56 commits)
ocfs2: Make cached block reads the common case.
ocfs2: Kill the last naked wait_on_buffer() for cached reads.
ocfs2: Move ocfs2_bread() into dir.c
ocfs2: Simplify ocfs2_read_block()
ocfs2: Require an inode for ocfs2_read_block(s)().
ocfs2: Separate out sync reads from ocfs2_read_blocks()
ocfs2: Refactor xattr list and remove ocfs2_xattr_handler().
ocfs2: Calculate EA hash only by its suffix.
ocfs2: Move trusted and user attribute support into xattr.c
ocfs2: Uninline ocfs2_xattr_name_hash()
ocfs2: Don't check for NULL before brelse()
ocfs2: use smaller counters in ocfs2_remove_xattr_clusters_from_cache
ocfs2: Documentation update for user_xattr / nouser_xattr mount options
ocfs2: make la_debug_mutex static
ocfs2: Remove pointless !!
ocfs2: Add empty bucket support in xattr.
ocfs2/xattr.c: Fix a bug when inserting xattr.
ocfs2: Add xattr mount option in ocfs2_show_options()
ocfs2: Switch over to JBD2.
ocfs2: Add the 'inode64' mount option.
...
|
|
We shouldn't rely on "pnp_platform_devices" to tell us whether there
is a PNP RTC device.
I introduced "pnp_platform_devices", but I think it was a mistake.
All it tells us is whether we found any PNPBIOS or PNPACPI devices.
Many machines have some PNP devices, but do not describe the RTC
via PNP. On those machines, we need to do the platform driver probe
to find the RTC.
We should just register the PNP driver and see whether it claims anything.
If we don't find a PNP RTC, fall back to the platform driver probe.
This (in conjunction with the arch/x86/kernel/rtc.c patch to add
a platform RTC device when PNP doesn't have one) should resolve
these issues:
http://bugzilla.kernel.org/show_bug.cgi?id=11580
https://bugzilla.redhat.com/show_bug.cgi?id=451188
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Rik Theys <rik.theys@esat.kuleuven.be>
Reported-by: shr_msn@yahoo.com.tw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Most if not all x86 platforms have an RTC device, but sometimes the RTC
is not exposed as a PNP0b00/PNP0b01/PNP0b02 device in PNPBIOS or ACPI:
http://bugzilla.kernel.org/show_bug.cgi?id=11580
https://bugzilla.redhat.com/show_bug.cgi?id=451188
It's best if we can discover the RTC via PNP because then we know
which flavor of device it is, where it lives, and which IRQ it uses.
But if we can't, we should register a platform device using the
compiled-in RTC_PORT/RTC_IRQ resource assumptions.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Rik Theys <rik.theys@esat.kuleuven.be>
Reported-by: shr_msn@yahoo.com.tw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move rtc_wake_setup() from drivers/acpi/glue.c into the RTC driver
in drivers/rtc/rtc-cmos.c.
This removes the ordering constraint between the module_init(acpi_rtc_init)
and the cmos_do_probe() code that depends on it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Once kernel configuration has CONFIG_HID turned on, let also all the
specialized drivers for quirky devices to be built (unless CONFIG_EMBEDDED is
specified), as usually users don't care that much which driver
gives them the functionality, but when they want generic support, they
probably want to have support for all the quirky devices as well.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This device is already handled by hid-apple driver, but the blacklist entry
was missing in generic driver.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This keyboard needs to reset the LEDS during probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Based on an original patch from Alexey Klimov <klimov.linux@gmail.com>,
against kernel version 2.6.27.
This device is already handled by radio-mr800 driver, and we therefore
want usbhid not to touch it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This keyboard needs to re-sync numlock after probing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
