Age | Commit message (Collapse) | Author |
|
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <linux@maxim.org.za>
[bart: minor checkpatch.pl / CodingStyle fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Commit 9567b349f7e7dd7e2483db99ee8e4a6fe0caca38 (ide: merge ->atapi_*put_bytes
and ->ata_*put_data methods) introduced a regression WRT the odd-length ATAPI
PIO transfers -- the final word didn't get written (causing command timeouts).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix this sparse warnings:
drivers/ide/ide-disk_proc.c:130:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-floppy_proc.c:32:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-proc.c:234:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-tape.c:2141:11: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Cc: trivial@kernel.org
Cc: kernel-janitors@vger.kernel.org
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
bart:
It seems like the bug could cause insanely long timeouts for:
- ATA_DMA_ERR error in dma_timer_expiry()
- commands without ->expiry in tc86c001_timer_expiry()
(TC86C001 IDE controller only)
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: port it to the current tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
fsl_get_sys_freq() may return -1 when 'soc' isn't found, but in
gef_wdt_probe() 'freq' is unsigned, so the test doesn't catch that.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
On arm-acs5k_tiny:
drivers/watchdog/ks8695_wdt.c:68: error: 'CLOCK_TICK_RATE' undeclared
(first use in this function)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>
|
|
Hanno Böck reported a problem where an old Conner CP30254 240MB hard drive
was reported as 1.1TB in capacity by libata:
http://lkml.org/lkml/2009/2/13/134
This was caused by libata trusting the drive's reported current capacity in
sectors in identify words 57 and 58 if the drive does not support LBA and the
current CHS translation values appear valid. Unfortunately it seems older
ATA specs were vague about what this field should contain and a number of drives
used values with wrong byte order or that were totally bogus. There's no
unique information that it conveys and so we can just calculate the number
of sectors from the reported current CHS values.
While we're at it, clean up this function to use named constants for the
identify word values.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When SCR access is available and the link is offline, softreset is
skipped as it only wastes time and some controllers don't respond very
well. However, the skip path forgot to thaw the port, which not only
blocks further event notification from the port but also causes
repeated EH invocations on the same event on drivers which rely on
->thaw() to clear events if the IRQ is shared with another device or
port.
This problem has always been there but is uncovered by recent sata_nv
nf2/3 change which dropped hardreset support while maintaining SCR
access. nf2/3 doesn't clear hotplug event mask from the interrupt
handler but relies on ->thaw() to clear them. When the hardreset was
there, the reset action was never skipped and the port was always
thawed but, with the hardreset gone, ->prereset() determines that
there's no need for softreset and both ->softreset() and ->thaw() are
skipped. This leads to stuck hotplug event in the IRQ status register
triggering hotplug event whenever IRQ is delieverd on the same IRQ.
As the controller shares the same IRQ for both ports, this happens on
every IO if one port is occpupied and the other isn't.
This patch fixes the problem by making sure that the port is thawed on
reset-skip path.
bko#11615 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Robert Hancock <hancockrwd@gmail.com>
Reported-by: Dan Andresan <danyer@gmail.com>
Reported-by: Arne Woerner <arne_woerner@yahoo.com>
Reported-by: Stefan Lippers-Hollmann <s.L-H@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Update MODULE_PARM_DESC for ADMA to reflect the fact that the
option is disabled by default.
Signed-off-by: Brandon Ehle <azverkan@yahoo.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Added the Device IDs for MCP89 AHCI controller.
Removed the IDs of MCP7B because this chipset had been cancelled.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
sense_buffer is used as DMA target and shouldn't be allocated on
stack. Use ap->sector_buf instead. This problem is spotted by Chuck
Ebbert.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
ap->sector_buf is used as DMA target and should at least be aligned on
cacheline. This caused problems on some embedded machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
libata passes the returned value of dma_map_sg() to
dma_unmap_sg(),which is the misuse of dma_unmap_sg().
DMA-mapping.txt says:
To unmap a scatterlist, just call:
pci_unmap_sg(pdev, sglist, nents, direction);
Again, make sure DMA activity has already finished.
PLEASE NOTE: The 'nents' argument to the pci_unmap_sg call must be
the _same_ one you passed into the pci_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
pci_map_sg call.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This fixes problems during resume with drives that take longer than 1s to
be ready. The ATA-6 spec appears to allow 5 seconds for a drive to be
ready.
On one affected system, this patch changes "PM: resume devices took..."
message from 17 seconds to 4 seconds, and gets rid of a lot of ugly
timeout/error messages.
Without this patch, the libata code moves on after 1s, tries to send a
soft reset (which the drive doesn't see because it isn't ready) which also
times out, then an IDENTIFY command is sent to the drive which times out,
and finally the error handler will try to send another hard reset which
will finally get things working.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Upon a 'transfer error block' size is set to -EINVAL, but this becomes positive
since size is unsigned: p->offset still gets incremented.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Commit 5e4c91c84b194b26cf592779e451f4b5be777cba forgot to remove the
initial sleep, get rid of it.
Thanks to Randy Dunlap <randy.dunlap@oracle.com> for spotting this error.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
When booting Xen Dom0 on a pre-release 3.2.1 hypervisor the system Oopses on a
"Unable to handle kernel NULL pointer dereference" in xenwatch.
From the backtrace it looks like backend_changed is calling bdget_disk
with a NULL pointer. Checking for NULL and returning ENODEV instead
allows the kernel to boot.
|
|
Use copy_to_user_page and copy_from_user_page instead of
memcpy. copy_to_user_page does cache flush when necessary.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
from "mem"
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Random read/write errors are a bad thing - so don't let anyone
(including the test bench) run on something we know is bad.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
instruction on bf561 after soft bp is hit
Run IFLUSH twice to avoid loading wrong instruction
after invalidating icache and following sequence is met.
1) The one instruction address is cached in the icache.
2) This instruction in SDRAM is changed.
3) IFLASH[P0] is executed only once in lackfin_icache_flush_range().
4) This instruction is executed again, but not the changed new one.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
|
|
As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.
Add a netdev_resync_ops() and call it from the vlan code.
Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.
With help from Patrick McHardy.
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IMHO the setting should depend on ANOMALY_05000305 which is about the
availability of the bit, not ANOMALY_05000265 which only describes the
SPORT sensitivity to noise (checked for BF561 only, though).
If that's not true for other BF variants, maybe the definition of
ANOMALY_05000265 for BF561 should be changed to '(1)' instead.
Signed-off-by: Enrik Berkhan <Enrik.Berkhan@ge.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Currently, tmspci tokenring driver crashes on device initialization
because it requests its irq before initializing corresponding data
structures. Fix this by moving request_irq call to a safer place.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A commit c1b56878fb68e9c14070939ea4537ad4db79ffae "tc: policing requires
a rate estimator" introduced a test which invalidates previously working
configs, based on examples from iproute2: doc/actions/actions-general.
This is too rigorous: a rate estimator is needed only when police's
"avrate" option is used.
Reported-by: Joao Correia <joaomiguelcorreia@gmail.com>
Diagnosed-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
|
|
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
|
|
This fixes a code regression caused by the recent mainlining changes.
The recent code changes call zlib_inflate repeatedly, decompressing into
separate 4K buffers, this code didn't check for the possibility that
zlib_inflate might ask for too many buffers when decompressing corrupted
data.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
|
|
I was seeing fsck errors on inode bitmaps after a 4 thread
dbench run on a 4 cpu machine:
Inode bitmap differences: -50736 -(50752--50753) etc...
I believe that this is because ext4_free_inode() uses atomic
bitops, and although ext4_new_inode() *used* to also use atomic
bitops for synchronization, commit
393418676a7602e1d7d3f6e560159c65c8cbd50e changed this to use
the sb_bgl_lock, so that we could also synchronize against
read_inode_bitmap and initialization of uninit inode tables.
However, that change left ext4_free_inode using atomic bitops,
which I think leaves no synchronization between setting &
unsetting bits in the inode table.
The below patch fixes it for me, although I wonder if we're
getting at all heavy-handed with this spinlock...
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Commit 6833c043f9fc03696fde623914c4a0277df2a0bc introduced the phy
auto-powerdown capability. While the APD feature only works for 5761
and 5784 asic revisions, the (harmless portion of the) code was applied
to all 5705 and newer devices. However, the 5906 phy departs from the
usual design. This commit was interfering with the 5906's ability to
negotiate link against some switches. This patch corrects the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dmatest_cleanup_chanel will free dtc, so grab ->chan before it goes away
and use it to do the release.
Reported-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
fix a probably accidently dropped reference operator while calling
spin_unlock_restore to an ipu lock.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Cc: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
iop_adma_zero_sum_self_test has the brackets in the wrong place for the
setup failure deallocation path. This error was duplicated in
mv_xor_xor_self_test.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Prevent dev_err from firing even if we successfully detected 'dma-idle'
before the full 1ms timeout has elapsed.
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
If we miss interrupts in the self test then fail registration of this
channel as it is unsuitable for use as a public channel.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Together with new fixes update driver version
and extend copyright dates ranges.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Trivial cleanup, list_del(); list_add_tail() is equivalent
to list_move_tail(). Semantic patch for coccinelle can be
found at www.cccmz.de/~snakebyte/list_move_tail.spatch
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Upcoming server platforms from Intel based on the Nehalem performance
have significantly improved CPU based copy performance.
However, the DMA engine can still be effective at higher I/O sizes
for TCP traffic and at this time copybreak
should be set to 256k for TCP traffic only.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Channel watchdog should be canceled before the rest of dma remove stuff.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
On some systems with I/OAT ver.2 when DCA is disabled in BIOS
situations have been observed
that zero DMA channels are detected instead of four.
To avoid kernel panic driver should fail gracefully with appropriate message.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Flag DCACTRL_CMPL_WRITE_ENABLE is valid only for I/OAT ver.2
so it should not be set for I/OAT ver.3.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|