aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-04-24V4L/DVB (7396): saa7134: fixed pointer in tuner callbackHartmut Hackmann
The pointer transferred directly points to the saa7134_dev structure Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7395): saa7134: start 2nd LND supply of Medion cards only if neededHartmut Hackmann
The ISL6405 LNB supply is used on several Creatix / Medion cards. But only the MD8800 needs its second section. So don't start it unless it is needed. Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7394): saa7134: add number of devices checkAlan McIvor
This patch fixes reported problems when trying to add a 9th device into a system. Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz> Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7393): tda827x: fixed support of tuners with LNAHartmut Hackmann
Tuner refactoring broke support of tuners with LNA configurations 1 and 2 for both, analog TV and DVB-T. Additionally, this patch initializes the saa713x gpios defined by the gpiomask at driver init to avoid undefined stated at dvb. Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7392): saa7134: support 2nd DVB-S section of the MD8800Hartmut Hackmann
There are some restrictions: - The 2nd DVB-S section will only work if the 1st is configured for DVB-S too. so "options saa7134-dvb use_frontend=0,1" won't work. - Currently it is not possible to set the higher LNB supply voltages, so 14V instead of 13V in the 2nd section. - It is not possibe to turn off the 2nd LNB supply independently. This comes from the problem that the 2nd section can't access the i2c interface of the LNB supply chip. Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7391): saa7134: Add DVB-S support for the MD 1734 cards with 2 saa7134Hartmut Hackmann
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7390): saa7134: clear audio DSP interface after access errorHartmut Hackmann
In the case of an access error to the high latency registers of the audio DSP, the interface needs to be cleared, otherwise a cascade of errors occurs. This patch is closely modeled after a proposal by Mirek Slugen Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7389): git-dvb: drivers/media/video/bt8xx/bttv-cards.c: fix warningsAndrew Morton
drivers/media/video/bt8xx/bttv-cards.c:3030:38: warning: "/*" within comment drivers/media/video/bt8xx/bttv-cards.c:3032:20: warning: "/*" within comment Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7388): saa7134: fix radio entry for xc2028/3028 boardsMauro Carvalho Chehab
If left in blank, the driver will use value 0 (Temic PAL) Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7387): saa7134: Fix xc3028 entriesMauro Carvalho Chehab
Tuner addresses were incorrect. Fix the entries. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7385): tda18271: store agc_mode configuration independently of std_bitsMichael Krufky
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7384): tda18271: store FM_RFn setting in struct tda18271_std_map_itemMichael Krufky
All standard related configuration is stored within struct tda18271_std_map_item. Pass a pointer to this structure rather than its individual members. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7383): tda18271: add attach-time parameter to limit i2c transfer sizeMichael Krufky
Add attach-time parameter, "small_i2c" to limit i2c transfer size to write at most 16 registers at a time during initialization. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7381): tuner: rename TUNER_PHILIPS_ATSC to TUNER_PHILIPS_FCV1236DMichael Krufky
TUNER_PHILIPS_ATSC is an ambiguous name for a tuner. Rename it to TUNER_PHILIPS_FCV1236D to be more descriptive. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7380): tuner-simple: warn if tuner can't be probed during attachMichael Krufky
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7379): tuner: prevent instance sharing if i2c adapter is NULLMichael Krufky
We currently do not have a method to enable instance staring if i2c adapter is NULL, in the cases of dvb demods that write to the tuner directly using calc_regs. Prevent possible wrong instance sharing for these cases until a better solution can be found. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7378): cleanup variable initializationGuennadi Liakhovetski
flags used for spinlocks don't need to be initialized, except where the compiler has no way to see, that the spin_unlock_irqrestore is only called if the spin_lock_irqsave has been called before. Local variable initialization doesn't have to be protected. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7377): radio-sf16fmr2.c: fix volume handlingMauro Carvalho Chehab
As reported by Roel Kluin <12o3l@tiscali.nl>: in drivers/media/radio/radio-sf16fmr2.c:319: for (i = 0; i < ARRAY_SIZE(radio_qctrl); i++) { if ((fmr2->card_type != 11) && V4L2_CID_AUDIO_VOLUME) radio_qctrl[i].step = 65535; ... I don't understand this '&& V4L2_CID_AUDIO_VOLUME' While fixing this issue, I've revisited the volume control code and fixed CodingStyle on the changed procedures. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7376): Improve compile-time type-checking in videobufGuennadi Liakhovetski
Make the dev member of the struct videobuf_queue of type "struct device *" to avoid future problems. Also change the prototype of the videobuf_queue_core_init() function. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7375): cx88/saa7134: fix magic number for xc3028 reusage detectionMauro Carvalho Chehab
tuner-xc2028 needs to know when a DVB module is sharing the same analog tuner. This is done by comparing a magic number that needs to be the same on analog and on digital. To make easier, this magic number is a pointer to some data struct. With the previous code, two different pointers were using, causing a miss-detection. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7374): Fix left-overs from the videobuf-dma-sg.c conversion to ↵Guennadi Liakhovetski
generic DMA The dev element of the struct videobuf_queue is now of type struct device implicitly. Fix left-over casts. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Reviewed-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7373): logical-bitwise & confusion in se401_init()Roel Kluin
logical-bitwise & confusion Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7372): cx88: Add IR support for Pixelview MPEG 8000GTMauro Carvalho Chehab
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7371): cx88: Fix audio on Prolink Pixelview Mpeg 8000GTMauro Carvalho Chehab
This board works only with non-mts firmware Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7370): Add basic support for Prolink Pixelview MPEG 8000GTMauro Carvalho Chehab
TV reception ok. S-video and Composite not tested. Audio not tested. IR not implemented yet. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7369): drivers/media/video/soc_camera.c: reads return size_tAndrew Morton
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> CC: Guennadi Liakhovetski <kernel@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7368): bttv: added support for Kozumi KTV-01C cardMauro Lacy
Signed-off-by: Mauro Lacy <mauro@lacy.com.ar> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7366): Support for a 16-channel bt878 cardErnesto Hernández-Novich
I have what looks like a Geovision GV-600 (or 650) card. It has a large chip in the middle labeled CONEXANT FUSION 878A 25878-13 E345881.1 0312 TAIWAN It has an audio connector coming out from a chip labeled ATMEL 0242 AT89C2051-24PI It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18) ... 01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) ... 01:0a.0 0400: 109e:036e (rev 11) Subsystem: 008a:763c Flags: bus master, medium devsel, latency 64, IRQ 58 Memory at dfffe000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 01:0a.1 0480: 109e:0878 (rev 11) Subsystem: 008a:763c Flags: bus master, medium devsel, latency 64, IRQ 58 Memory at dffff000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18 kernel and the latest v4l-dvb drivers, but it did not work at all. The card has sixteen (16) BNC video inputs, four of them on the board itself and twelve on three daughter-cards. It has a single bt878 chip, no tuner and what looks like and audio input. After doing some research I managed to get only eight channels working by forcing card=125 and those DID NOT match channels 0-7 on the card, and no audio. Based on what was working for card=125, I added the card definition block, added a specific muxsel routine and got the card working fully with xawtv, where the sixteen channels show up as Composite0 to Composite15, matching the channel labels in the card and daughter-cards. I have made no efforts yet to get audio working, but would appreciate any pointers. Signed-off-by: Ernesto Hernández-Novich <emhn@usb.ve> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7365): reduce stack usage of v4l1_compat_syncMarcin Slusarz
poll_one allocated on stack struct poll_wqueues which is pretty big structure (>500 bytes on x86_64). v4l1_compat_sync invokes poll_one in a loop, so allocate struct poll_wqueues in v4l1_compat_sync (with kmalloc) and pass it to poll_one. Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7364): reduce stack usage of v4l_compat_translate_ioctlMarcin Slusarz
v4l_compat_translate_ioctl used 1376 bytes of stack (x86_64), so split this 800 lines long function into ~20 small noinline functions; the biggest function takes now 712 bytes (v4l1_compat_sync) fix VIDIOCSWIN handler which printked wrong errors Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7363): fix coding style violations in v4l1-compat.cMarcin Slusarz
fix most coding style violations found by checkpatch Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7360): tuner-simple: fix return value of simple_dvb_configureMichael Krufky
simple_dvb_configure returns the actual tuned frequency to its caller, so it must be declared as a u32 rather than an int. As a result, we will return 0 to indicate a failure. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7359): tuner-simple: enable digital tuning support for Thomson FE6600Michael Krufky
Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7358): tuner-simple: enable digital tuning support for Philips TD1316Michael Krufky
Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7357): tuner-simple: enable digital tuning support for Microtune ↵Michael Krufky
4042 FI5 Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7356): tuner-simple: enable digital tuning support for Thomson DTT 7610Michael Krufky
Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7355): tuner-simple: use separate inputs for vsb and qam on ↵Michael Krufky
tuv1236d & fcv1236d Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7354): tuner-simple: enable digital tuning support for Philips FCV1236DMichael Krufky
Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7353): tuner-simple: enable digital tuning support for Philips TUV1236DMichael Krufky
Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7352): tuner-simple: enable digital tuning support for Philips ↵Michael Krufky
FMD1216ME Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7351): tuner-simple: add init and sleep methodsMichael Krufky
taken from dvb-pll Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7350): tuner-simple: enable digital tuning support for Thomson DTT 761XMichael Krufky
Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7349): tuner-simple: enable digital tuning support for LG TDVS-H06xFMichael Krufky
Enable digital tuning support within tuner-simple. This will allow for a single tuner module to manage the hardware, without having dvb-pll loaded. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7348): tuner-simple: do not send i2c commands if there is no i2c ↵Michael Krufky
adapter if (priv->i2c_props.adap == NULL) then exit any function that would send commands over the i2c bus. We allow drivers to attach without an i2c adapter for cases where the dvb demod accesses the tuner directly via calc_regs. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7347): tuner-simple: add basic support for digital tuning of hybrid ↵Michael Krufky
devices Add entry points used for digital tuning via the dvb_frontend. Share state data between multiple instances of the driver for hybrid tuners. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7346): tda9887: allow multiple driver instances for the same ↵Michael Krufky
hardware to share state Convert tda9887 to use the new hybrid_tuner_request_state and hybrid_tuner_release_state macros to manage state sharing between hybrid tuner instances. Some ATSC/DVB cards need to put the analog demodulator into standby before tuning digital. This patch allows us to attach the tda9887 driver to the digital side of the bridge driver and be able to put it into standby without jeopardizing the analog demod driver's state. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7344): cx25840: better PAL-M and NTSC-KR handlingHans Verkuil
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7343): msp3400: fix SECAM D/K handlingHans Verkuil
The 6.5 MHz carrier was interpreted as SECAM-L even if SECAM-D/K was selected. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7342): saa7115: fix PAL-Nc handlingHans Verkuil
Fsc 3.58 refers to Combination PAL-N (aka PAL-Nc), not to plain PAL-N (that uses Fsc 4.43). Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-04-24V4L/DVB (7341): ivtv: rename tunerhz to tunertypeHans Verkuil
There are two tuner types: those for M/N standards and those for all others. However, M/N standards are not always 60 Hz (PAL-N/Nc are 50 Hz), so rename the module option accordingly. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-20 08:13:10 +0000