| Age | Commit message (Collapse) | Author |
|---|
|
In P_Key event handling, if the old P_Key is no longer available, the
driver must call ipoib_ib_dev_stop() -- just as it does when the P_Key
is still available (see procedure __ipoib_ib_dev_flush()).
When a P_Key becomes available, the driver will perform ipoib_open(),
which assumes that the QP is in RESET, the cm_id has been
destroyed/deleted, etc. If ipoib_ib_dev_stop() is not called as
described above, then these assumptions will be false, and the attempt
to bring the interface up will fail.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
replace:
big_endian_variable = cpu_to_beX(beX_to_cpu(big_endian_variable) +
expression_in_cpu_byteorder);
with:
beX_add_cpu(&big_endian_variable, expression_in_cpu_byteorder);
Generated with a semantic patch.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The cxgb3 HW and driver don't support loopback RDMA connections. So
fail any connection attempt where the destination address is local.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit 9af57b7a ("IB/cm: Add basic performance counters") introduced a
bug in how the reference count for cm_class.subsys.kobj was handled:
the path that released a device did a kobject_put() on that kobject, but
there was no kobject_get() in the path the handles adding a device. So
the reference count ended up too low, which leads to bad things. Fix up
and simplify the reference counting to avoid this.
(Actually, I introduced the bug when fixing the patch up to match some
of Greg's kobject changes, but who's counting)
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Pesky little devils, sneaking around...
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Usually harmless, since the scatterlist is always hard-coded to a length
of 1, but it triggers a BUG() if CONFIG_DEBUG_SG=y, so we better fix it.
This fixes <http://bugzilla.kernel.org/show_bug.cgi?id=9934>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Even if we don't want to register the WMI driver, we should initialize
the wmi_blocks list to be empty, since we don't want the wmi helper
functions to oops just because that basic list has not even been set up.
With this, "find_guid()" will happily return "not found" rather than
oopsing all over the place, and the callers will then just automatically
return false or AE_NOT_FOUND as appropriate.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The makefile magic for installing the 32-bit vdso images on disk had a
little error. A single-line change would fix that bug, but this does a
little more to reduce the error-prone duplication of this bit of
makefile variable magic.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Kosaki Motohito noted that "numactl --interleave=all ..." failed in the
presence of memoryless nodes. This patch attempts to fix that problem.
Some background:
numactl --interleave=all calls set_mempolicy(2) with a fully populated
[out to MAXNUMNODES] nodemask. set_mempolicy() [in do_set_mempolicy()]
calls contextualize_policy() which requires that the nodemask be a
subset of the current task's mems_allowed; else EINVAL will be returned.
A task's mems_allowed will always be a subset of node_states[N_HIGH_MEMORY]
i.e., nodes with memory. So, a fully populated nodemask will be
declared invalid if it includes memoryless nodes.
NOTE: the same thing will occur when running in a cpuset
with restricted mem_allowed--for the same reason:
node mask contains dis-allowed nodes.
mbind(2), on the other hand, just masks off any nodes in the nodemask
that are not included in the caller's mems_allowed.
In each case [mbind() and set_mempolicy()], mpol_check_policy() will
complain [again, resulting in EINVAL] if the nodemask contains any
memoryless nodes. This is somewhat redundant as mpol_new() will remove
memoryless nodes for interleave policy, as will bind_zonelist()--called
by mpol_new() for BIND policy.
Proposed fix:
1) modify contextualize_policy logic to:
a) remember whether the incoming node mask is empty.
b) if not, restrict the nodemask to allowed nodes, as is
currently done in-line for mbind(). This guarantees
that the resulting mask includes only nodes with memory.
NOTE: this is a [benign, IMO] change in behavior for
set_mempolicy(). Dis-allowed nodes will be
silently ignored, rather than returning an error.
c) fold this code into mpol_check_policy(), replace 2 calls to
contextualize_policy() to call mpol_check_policy() directly
and remove contextualize_policy().
2) In existing mpol_check_policy() logic, after "contextualization":
a) MPOL_DEFAULT: require that in coming mask "was_empty"
b) MPOL_{BIND|INTERLEAVE}: require that contextualized nodemask
contains at least one node.
c) add a case for MPOL_PREFERRED: if in coming was not empty
and resulting mask IS empty, user specified invalid nodes.
Return EINVAL.
c) remove the now redundant check for memoryless nodes
3) remove the now redundant masking of policy nodes for interleave
policy from mpol_new().
4) Now that mpol_check_policy() contextualizes the nodemask, remove
the in-line nodes_and() from sys_mbind(). I believe that this
restores mbind() to the behavior before the memoryless-nodes
patch series. E.g., we'll no longer treat an invalid nodemask
with MPOL_PREFERRED as local allocation.
[ Patch history:
v1 -> v2:
- Communicate whether or not incoming node mask was empty to
mpol_check_policy() for better error checking.
- As suggested by David Rientjes, remove the now unused
cpuset_nodes_subset_current_mems_allowed() from cpuset.h
v2 -> v3:
- As suggested by Kosaki Motohito, fold the "contextualization"
of policy nodemask into mpol_check_policy(). Looks a little
cleaner. ]
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Fix build for sim_defconfig
|
|
So I spent a while pounding my head against my monitor trying to figure
out the vmsplice() vulnerability - how could a failure to check for
*read* access turn into a root exploit? It turns out that it's a buffer
overflow problem which is made easy by the way get_user_pages() is
coded.
In particular, "len" is a signed int, and it is only checked at the
*end* of a do {} while() loop. So, if it is passed in as zero, the loop
will execute once and decrement len to -1. At that point, the loop will
proceed until the next invalid address is found; in the process, it will
likely overflow the pages array passed in to get_user_pages().
I think that, if get_user_pages() has been asked to grab zero pages,
that's what it should do. Thus this patch; it is, among other things,
enough to block the (already fixed) root exploit and any others which
might be lurking in similar code. I also think that the number of pages
should be unsigned, but changing the prototype of this function probably
requires some more careful review.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Fix build break (missing include)
|
|
Matt is already the maintainer of SLOB which is one of the "SLAB" allocators in
the kernel so add him to MAINTAINERS.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: platform driver allocs dma without create
pata_ninja32: setup changes
pata_legacy: typo fix
pata_amd: Note in the module description it handles Nvidia
sata_mv: fix loop with last port
libata: ignore deverr on SETXFER if mode is configured
pata_via: fix SATA cable detection on cx700
|
|
This avoids warnings with unreferenced variables in the !NUMA case.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 313abe55 ("mlx4_core: For 64-bit systems, vmap() kernel queue
buffers") caused this to pop up on powerpc allyesconfig, looks like a
missing include file:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:162: error: implicit declaration of function 'vmap'
drivers/net/mlx4/alloc.c:162: error: 'VM_MAP' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:162: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:162: error: for each function it appears in.)
drivers/net/mlx4/alloc.c:162: warning: assignment makes pointer from integer without a cast
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_free':
drivers/net/mlx4/alloc.c:187: error: implicit declaration of function 'vunmap'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commit bdc807871d58285737d50dc6163d0feb72cb0dc2 broke the build
for this config because the sim_defconfig selects CONFIG_HZ=250
but include/asm-ia64/param.h has an ifdef for the simulator to
force HZ to 32. So we ended up with a kernel/timeconst.h set
for HZ=250 ... which then failed the check for the right HZ
value and died with:
Drop the #ifdef magic from param.h and make force CONFIG_HZ=32
directly for the simulator.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
When the sata_mv driver is used as a platform driver,
mv_create_dma_pools() is never called so it fails when trying
to alloc in mv_pool_start().
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Forcibly set more of the configuration at init time. This seems to fix at
least one problem reported. We don't know what most of these bits do, but
we do know what windows stuffs there.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This has confused a few people so fix it
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
commit f351b2d638c3cb0b95adde3549b7bfaf3f991dfa
sata_mv: Support SoC controllers
cause panic:
scsi 4:0:0:0: Direct-Access ATA HITACHI HDS7225S V44O PQ: 0 ANSI: 5
sd 4:0:0:0: [sde] 488390625 512-byte hardware sectors (250056 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sde] 488390625 512-byte hardware sectors (250056 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde:<1>BUG: unable to handle kernel NULL pointer dereference at 000000000000001a
IP: [<ffffffff806262c7>] mv_interrupt+0x21c/0x4cc
PGD 0
Oops: 0000 [1] SMP
CPU 3
Modules linked in:
Pid: 0, comm: swapper Not tainted 2.6.24-smp-08636-g0afc2ed-dirty #26
RIP: 0010:[<ffffffff806262c7>] [<ffffffff806262c7>] mv_interrupt+0x21c/0x4cc
RSP: 0000:ffff8102050bbec8 EFLAGS: 00010297
RAX: 0000000000000008 RBX: 0000000000000000 RCX: 0000000000000003
RDX: 0000000000008000 RSI: 0000000000000286 RDI: ffff8102035180e0
RBP: 0000000000000001 R08: 0000000000000003 R09: ffff8102036613e0
R10: 0000000000000002 R11: ffffffff8061474c R12: ffff8102035bf828
R13: 0000000000000008 R14: ffff81020348ece8 R15: ffffc20002cb2000
FS: 0000000000000000(0000) GS:ffff810405025700(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 000000000000001a CR3: 0000000000201000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff810405094000, task ffff8102050b28c0)
Stack: 000000010000000c 0002040000220400 0000001100000002 ffff81020348eda8
0000000000000001 ffff8102035f2cc0 0000000000000000 0000000000000000
0000000000000018 0000000000000000 0000000000000000 ffffffff80269ee8
Call Trace:
<IRQ> [<ffffffff80269ee8>] ? handle_IRQ_event+0x25/0x53
[<ffffffff8026b393>] ? handle_fasteoi_irq+0x90/0xc8
[<ffffffff802218e2>] ? do_IRQ+0xf1/0x15f
[<ffffffff8021df24>] ? default_idle+0x0/0x55
[<ffffffff8021f361>] ? ret_from_intr+0x0/0xa
<EOI> [<ffffffff8023010c>] ? lapic_next_event+0x0/0xa
[<ffffffff8021df55>] ? default_idle+0x31/0x55
[<ffffffff8021df50>] ? default_idle+0x2c/0x55
[<ffffffff8021df24>] ? default_idle+0x0/0x55
[<ffffffff8021e00b>] ? cpu_idle+0x92/0xb8
Code: 41 14 85 c0 89 44 24 14 0f 84 9d 02 00 00 f7 d0 01 d6 41 89 d5 89 41 14 8b 41 14 89 34 24 e9 7e 02 00 00 49 63 c5 49 8b 5c c6 48 <f6> 43 1a 80 4c 8b a3 20 37 00 00 0f 85 62 02 00 00 31 c9 41 83
RIP [<ffffffff806262c7>] mv_interrupt+0x21c/0x4cc
RSP <ffff8102050bbec8>
CR2: 000000000000001a
---[ end trace 2583b5f7a5350584 ]---
Kernel panic - not syncing: Aiee, killing interrupt handler!
last_port already include port0 base.
this patch change use last_port directly, and move pp assignment later.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Some controllers (VIA CX700) raise device error on SETXFER even after
mode configuration succeeded. Update ata_dev_set_mode() such that
device error is ignored if transfer mode is configured correctly. To
implement this, device is revalidated even after device error on
SETXFER.
This fixes kernel bugzilla bug 8563.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The first port of cx700 is SATA. Fix cable detection.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
pageattr-test.c contains a noisy debug printk that people reported.
The condition under which it prints (randomly tapping into a mem_map[]
hole and not being able to c_p_a() there) is valid behavior and not
interesting to report.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: fix make V=1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
selinux: support 64-bit capabilities
|
|
Without this patch a Opteron test system here oopses at boot with
current git.
Calling to_pci_dev() on a NULL pointer gives a negative value so the
following NULL pointer check never triggers and then an illegal address
is referenced. Check the unadjusted original device pointer for NULL
instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://linux-nfs.org/~bfields/linux:
SUNPRC: Fix printk format warning
nfsd: clean up svc_reserve_auth()
NLM: don't requeue block if it was invalidated while GRANT_MSG was in flight
NLM: don't reattempt GRANT_MSG when there is already an RPC in flight
NLM: have server-side RPC clients default to soft RPC tasks
NLM: set RPC_CLNT_CREATE_NOPING for NLM RPC clients
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: remove stale comment from ide-lib.c
ide: fix comment in init_irq()
ide: ide_init_port() bugfix
ide-disk: fix flush requests (take 2)
ide: introduce CONFIG_BLK_DEV_IDEDMA_SFF option
bast-ide: build fix
ide-tape: remove never executed code
ide: fix ide/legacy/gayle.c compilation
ide-cd: replace ntohs with generic byteorder macro be16_to_cpu
ide: remove stale version number
pdc202xx_old: always enable burst mode
palm_bk3710: use struct ide_port_info
palm_bk3710: port initialization/probing bugfix
palm_bk3710: fix ide_unregister() usage
palm_bk3710: ide_register_hw() -> ide_device_add()
ide: insert BUG_ON() into __ide_set_handler() (take 2)
cs5520: remove stale comment
ide: another possible ide panic fix for blk-end-request
|
|
When make -s support were added to filechk to
combination created with make V=1 were not
covered.
Fix it by explicitly cover this case too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Mike Frysinger <vapier@gentoo.org>
|
|
Since we may not have a pci_dev for the device we need to access, we can't
use pci_read_config_word. But raw_pci_read is an internal implementation
detail; it's better to use the architected pci_bus_read_config_word
interface. Using PCI_DEVFN instead of a mysterious constant helps
reassure everyone that we really do intend to access device 8.
[ Thanks to Grant Grundler for pointing out to me that this is exactly
what the write immediately above this is doing -- enabling device 8 to
respond to config space cycles.
- Matthew
Grant also says:
"Can you also add a comment which points at the Intel
documentation?
The 'Intel E7320 Memory Controller Hub (MCH) Datasheet' at
http://download.intel.com/design/chipsets/datashts/30300702.pdf
Page 69 documents register F4h (DEVPRES1).
And I just doubled checked that the 0xf4 register value is
restored later in the quirk (obvious when you look at the code
but not from the patch"
so here it is.
- Linus ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix SELinux to handle 64-bit capabilities correctly, and to catch
future extensions of capabilities beyond 64 bits to ensure that SELinux
is properly updated.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
APUS support is gone...
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
On Sunday 10 February 2008, Atsushi Nemoto wrote:
> On Sun, 06 Jan 2008 18:03:10 +0100, Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> wrote:
> > + /* reset DMA masks only for SFF-style DMA controllers */
> > + if ((d->host_flags && IDE_HFLAG_NO_DMA) == 0 && hwif->dma_base == 0)
> > + hwif->swdma_mask = hwif->mwdma_mask = hwif->ultra_mask = 0;
>
> It might be too late, but "host_flags && IDE_HFLAGS_NO_DMA" seems
> wrong for me.
Fix regression caused by commmit c413b9b94d9a8e7548cc4b2e04b7df0439ce76fd
("ide: add struct ide_port_info instances to legacy host drivers").
Reported-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
commit 813a0eb233ee67d7166241a8b389b6a76f2247f9
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Fri Jan 25 22:17:10 2008 +0100
ide: switch idedisk_prepare_flush() to use REQ_TYPE_ATA_TASKFILE requests
...
broke flush requests.
Allocating IDE command structure on the stack for flush requests is not
a very brilliant idea:
- idedisk_prepare_flush() only prepares the request and it doesn't wait
for it to be completed
- there are can be multiple flush requests queued in the queue
Fix the problem (per hints from James Bottomley) by:
- dynamically allocating ide_task_t instance using kmalloc(..., GFP_ATOMIC)
- adding new taskfile flag (IDE_TFLAG_DYN)
- calling kfree() in ide_end_drive_command() if IDE_TFLAG_DYN is set
(while at it rename 'args' to 'task' and fix whitespace damage)
[ This will be fixed properly before 2.6.25 but this bug is rather
critical and the proper solution requires some more work + testing. ]
Thanks to Sebastian Siewior and Christoph Hellwig for reporting the
problem and testing patches (extra thanks to Sebastian for bisecting
it to the guilty commmit).
Tested-by: Sebastian Siewior <ide-bug@ml.breakpoint.cc>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Introduce new option CONFIG_BLK_DEV_IDEDMA_SFF for non-PCI SFF-8038i compatible
bus mastering IDE controllers (which there are a few known), thus fixing a hack
made for Palmchip BK3710 controller...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
On Saturday 09 February 2008, Adrian Bunk wrote:
> Commit 9e016a719209d95338e314b46c3012cc7feaaeec causes the following
> compile error:
>
> <-- snip -->
>
> ...
> CC drivers/ide/arm/bast-ide.o
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c: In function 'bastide_register':
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:31: error: 'hwif' redeclared as different kind of symbol
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:29: error: previous definition of 'hwif' was here
> make[4]: *** [drivers/ide/arm/bast-ide.o] Error 1
>
> <-- snip -->
Remove 'ide_hwif_t **hwif' argument from bastide_register()
(together with write-only ifs[]).
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
rq->cmd[0] is never set to REQ_IDETAPE_READ_BUFFER so remove
REQ_IDETAPE_READ_BUFFER handling from idetape_create_write_cmd()
and the define itself.
Then remove no longer used idetape_create_read_buffer_cmd()
and IDETAPE_RETRIEVE_FAULTY_BLOCK define.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
On Thursday 03 January 2008, Robert Hancock wrote:
[...]
> How about getting rid of this stupid thing in drivers/ide/ide.c:
>
> #define REVISION "Revision: 7.00alpha2"
>
> which is used in:
>
> printk(KERN_INFO "Uniform Multi-Platform E-IDE driver " REVISION "\n");
>
> It's been 7.00alpha2 for god knows how long, so clearly this version
> number is not useful..
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Alan has noticed that distros always enabled burst mode
(+ datasheet confirms that it is the right thing to do).
Thus fix pdc202xx_old host driver to do it unconditionally
and remove no longer needed CONFIG_PDC202XX_BURST option.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out cable detection to palm_bk3710_cable_detect().
* Add palm_bk3710_init_hwif() (->init_hwif method implementation).
* Remove needless ->quirkproc initialization.
* Add missing ->pio_mask initialization.
* Use ATA_* defines for setting ->{ultra,mwdma}_mask.
* Add 'struct ide_port_info palm_bk3710_port_info' and pass it to
ide_device_add(). Then remove open-coded 'hwif' initialization.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Probe port _after_ it is fully initialized.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Don't set 'restore' flag for ide_unregister() when initializing new
interface.
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 909f4369bca30f9a186316a3bf2b4a9c1e702a25 ]
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Convert palm_bk3710 host driver to use ide_device_add() instead of
ide_register_hw() (while at it drop doing "ide_unregister()" loop which
tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 9e016a719209d95338e314b46c3012cc7feaaeec ]
* Rename 'ide_ctlr_info' to 'hw' and 'index' to 'i' while at it.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Replace the check for hwgroup->handler and printk(KERN_CRIT, ...) at the start
of __ide_set_handler() with mere BUG_ON() while removing such from the caller,
ide_execute_command(). Fix up the code formatting, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove stale comment from the cs5520 IDE driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
