| Age | Commit message (Collapse) | Author |
|---|
|
Disable pcf interrupt (not for wake, just as interrupt) in
suspend, re-enable it again just before we force-call the
workqueue function at end of pcf resume, which leads to
pcf interrupt source registers getting cleared so it can
signal an interrupt normally again.
This change ends the uncontrolled appearance of pcf interrupts
during resume time which previously caused the work to attempt
to use the I2C stuff before i2c host device had itself resumed.
Now the isr work is only queued, and the isr work function called,
definitively after pcf resume completes.
In suspend time, the work function may have been queued some
time before and be pending, and it could still show up at a
bad time. Therefore if the work function sees that it is
coming since the start of pcf50633 suspend function, it
aborts without attempting to read the pcf interrupt regs,
leaving them for resume to take care of.
USB current limit and no battery work functions are also made
aware of suspend state and act accordingly.
Lastly I noticed that in early resume, i2c_get_clientdata(&pcf->client)
returns NULL, presumably because i2c device is still suspended. This
could easily make trouble for async events like interrupt work,
since pcf pointer is the client data. Disabling appearance of the
work until after pcf50633 resume will also avoid that.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Use an enum to define pcf50633 suspend / resume state.
Add PCF50633_SS_RESUMING_BUT_NOT_US_YET to be the state
early in resume: add platform driver resume function just
to set this state so we can differentiate between early
resume and late suspend.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Whoops left it up in suspend
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
mach-gta02 meddles with the regulator platform struct after
it is defined, leading to LCM power getting lost in suspend
despite I set it to be left up. Fixing this finally removes
the incredibly stubborn white LCM on suspend "flash".
This is also going to be implicated in Sean McNeil's
experience of monochromatic LCM after resume, which was
previously attacked by resetting and re-initing the LCM
from scratch.
In addition, I realized that we take down core_1v3 in
pcf50633 suspend action, this is happening near the
start of suspend, so we are in a meta-race to finish
suspend in a controlled way before the caps on core_1v3
run out (I only saw 23.3uF total). If it's true, this
is where the weirdo sensitivity to timing during
suspend is coming from.
Therefore in this patch we also remove sleeps and
dev_info() etc (which have to flush on serial console)
from the pc50633 isr workqueue if we are in pcf50633
driver suspend state 1, ie, suspending... because we
don't have time for it.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Sean McNeil reports that he doesn't get pcf50633 interrupts any
more after resume. This adds back the call to ISR work in
the resume, removal of which is probably to do with it.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
If you boot from SDCARD, this helper script for the build host
mounts SD card part 1, copies the new uImage.bin, umounts it and
then remounts SD card part 2 as ro, before doing a reboot all
in one step. Read the instructions inside the script for adding
your public key to the GTAxx rootfs for really really simple and
nice automatic update and reboot action.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
The LCM spins for 100ms during resume for not much reason. Leave it powered
(it is meant to pull uA when suspended) and get nice fast resume to video.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
pcf50633 needs to take responsibility for managing current limit
changes asycnhrnously, ie, from USB stack enumeration. It's a feature of
pcf50633 not mach-gta02.c, and we can do better with taking care about
keeping it from firing at a bad time in there too.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Simplify and speed up bulk sequential I2C actions in pcf50633
the time savings are pretty considerable and so is the simplification
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
More pcf50633 major time saving by using i2c bulk autoincrement. Code
reduction too by using array for time elements.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Improve pcf50633 interrupt service scheduling to enforce only servicing
when resume action is completed
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Glamo MCI has a resume order dependncy on pcf50633, it has to be able to
power the SD slot via it.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Glamo MCI power setting stuff spins on pcf50633
but it won't hurt if it gives up after a second or
two instead of stalling the resume silently.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Sean McNeil reports that without the reset for LCM in suspend, he
gets a monochromatic mode on it somehow.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
After protecting pcf50633 read and write primitives against
operation after suspend or before resume (by blowing a
stack_trace()) I saw glamo-mci was trying to use pcf50633
at these bad times on its own suspend and resume. Since that
part was already done via platform callback, I added an
export in pcf50633 that tells you if it is ready or busy,
and used it to defer (resume power on case) or ignore
(suspend power off case, since pcf50633 already did it)
the mci power call.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
- speed up suspend and resume by using one hit i2c bulk transactions
- don't bother storing int mask set on suspend, the default one is
what we use anyway
- put stack_trace() on pcf50633 low level access that fire if we
try to touch them before we resumed
- cosmetic source cleanup
- reduces resume time for pcf50633 from 450ms to 255ms
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Allow direct setting of codec registers for super mega meddling power
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
Adds the resume callback stuff to glamo, then changes
jbt6k74 to no longer use a sleeping workqueue, but to
make its resume actions dependent on pcf50633 and
glamo resume (for backlight and communication to LCM
respectively)
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Adds resume dependency support to pcf50633
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Defines a way for drivers to defer execution of resume callbacks
until one or more other driver they are dependent on has itself
resumed.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Creates a new behaviour requested by Will that the red LED on GTA02
is lit during battery charging.and goes out when the battery is full.
This is done by leveraging the PMU interrupts, but in one scenario
there is no interrupt that occurs, when the battery is replaced after
being removed with the USB power in all the while. So a sleepy work
function is started under those circumstances to watch for battery
reinsertion or USB cable pull.
100mA limit was not being observed under some conditions so this was
fixed and tested with a USB cable with D+/D- disconnected. 1A
charger behaviour was also tested.
Showing the charging action exposes some inconsistency in pcf50633
charging action. If your battery is nearly full, it will keep
charging it at decreasing current even after it thinks it is at
100% capacity for a long while. But if you pull that same battery
and re-insert it, the charger state machine in pcf50633 believe it is
full and won't charge it.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
X-Git-Url: http://git.openmoko.org/?p=kernel.git;a=commitdiff_plain;h=7f52bae9664cbf006fe026d4dbbd5988137bd1cc
config-defconfig-2.6.26.patch
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
|
|
From 4cb4c308fde9c1f3598046ff98191d14b62bc609 Mon Sep 17 00:00:00 2001
From: Holger Freyther <zecke@openmoko.org>
Date: Thu, 29 May 2008 00:09:32 +0200
Subject: [PATCH] [ar6k] silent++, removing -DDEBUG from the Makefile does not
work
|
|
From 0b9bae6aed5268707b348e48a01411ba420844e1 Mon Sep 17 00:00:00 2001
From: Holger Freyther <zecke@openmoko.org>
Date: Tue, 27 May 2008 14:41:35 +0200
Subject: [PATCH] [janitor] Fix possible null pointer dereference
Judging by the control flow of the resume method i2c->suspended++ could
lead to a null pointer dereference.
|
|
Model name isn't in the bq27000 register set, remove the
claim that we can deliver it
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Update this old code to clk API, I2C changes, official GPIO API
various struct changes, explicit readl() writel(), DMA API changes.
Still not ready for actual use (eg, I2C) but a LOT closer.
Compiles on 2.6.24 without errors or warnings now.
Use CONFIG_S3C2440_CAMERA=y in .config
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This is the kernel side of an old (2004) samsung camera driver for 2440
It doesn't compile on modern kernel yet, this patch introduces it into the
kernel tree without gross mods, so it is broken code we can start to work on
|
|
Adds the somewhat simpler resume source support for GTA01
since PMU is not a wake source
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Currently we are willing to wake from sleep from
pcf50633 interrupts we don't actually do anything about
even when we wake (somewhat puzzled).
Let's disable some of these wake sources.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
If you have U-Boot with uboot-add-find-wake-reason.patch, this
patch will get you a wake reason report from
cat /sys/devices/platform/neo1973-resume.0/resume_reason
it looks like this:
EINT00_ACCEL1
EINT01_GSM
EINT02_BLUETOOTH
EINT03_DEBUGBRD
EINT04_JACK
EINT05_WLAN
EINT06_AUXKEY
EINT07_HOLDKEY
EINT08_ACCEL2
* EINT09_PMU
adpins
adprem
usbins
usbrem
rtcalarm
second
onkeyr
onkeyf
exton1r
exton1f
exton2r
exton2f
exton3r
exton3f
* batfull
chghalt
thlimon
thlimoff
usblimon
usblimoff
adcrdy
onkey1s
lowsys
lowbat
hightmp
autopwrfail
dwn1pwrfail
dwn2pwrfail
ledpwrfail
ledovp
ldo1pwrfail
ldo2pwrfail
ldo3pwrfail
ldo4pwrfail
ldo5pwrfail
ldo6pwrfail
hcidopwrfail
hcidoovl
EINT10_NULL
EINT11_NULL
EINT12_GLAMO
EINT13_NULL
EINT14_NULL
EINT15_NULL
This shows a problem, false wake from suspend due to battery full
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
From dc6d335b467646d802a21ea6b925ee97e83e07be Mon Sep 17 00:00:00 2001
From: Holger Freyther <zecke@openmoko.org>
Date: Thu, 15 May 2008 01:16:23 +0200
Subject: [PATCH] Do not use msleep in the resume path of s3c2410_ts as it
might lockup
For some reason msleep might set the only task running into a suspended
state and no timer will ever wake it up. Use mdelay to avoid this. I was not
able to understand the reasoning of sleeping after enabling the clock. So we
might just remove the msleep/mdelay at all and be fine.
Signed-Off-By: Holger Freyther <zecke@openmoko.org>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This patch improves the smoothness of suspend and resume action.
Taking out CONFIG_PM_DEBUG allows much more rapid resume (the low level
serial traffic appears to be synchronous)
Added a platform callback in jbt driver and support in pcf50633 so we
can defer bringing up the backlight until the LCM is able to process
video again (which must happen after the glamo is up and producing
video beacuse the LCM is hooked to glamo SPI)
GTA01 should not be affected by all this as the callback will default
to null and it is on pcf50606
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This patch is to register pwm as platform driver to keep the PWM-related
config when system is in suspend/resume. This could fix the following
issue after resume:
- HDQ read timeout
- LEDs blinked abnormally(if LEDs is driven by PWM)
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
|
|
the KEY_PHONE is backwards. It returns up when pushed and down when
released. The following change fixes it:
Signed-off-by: Sean McNeil <sean@mcneil.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
fix trailing whitespace and function args for suspend.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Subject: [PATCH] - add suspend/resume function of s3c24xx_hcd driver
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
|
|
--> (http://bugzilla.openmoko.org/cgi-bin/bugzilla/attachment.cgi?id=595&action=view)
fix resume of fbdev BZ#79
I played a bit with the fbdev resume. With this patch the neo doesn't get this
white screen on resume from console and from X.
Signed-off-by: Reddog <reddog@mastersword.de>
|
|
Created an attachment (id=594) / BZ#79
Add missing platform_data that caused the GTA01 to crash on suspend/resume
The interface to the jbt6k74 driver changed slightly; this patch adds the
missing platform_data for the GTA01. This prevents a crash while suspending.
This patch also makes some minor changes to cleanup and clarify some debug
messages.
Signed-off-by: Mike Westerhof <mwester@dls.net>
|
