| Age | Commit message (Collapse) | Author |
|---|
|
Depending on how the 44x processors are wired, some EMAC cells
might not be useable (and not connected to a PHY). However, some
device-trees may choose to still expose them (since their registers
are present in the MMIO space) but with an "unused" property in them.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
With some PHYs, when the link goes away, the EMAC reset fails due
to the loss of the RX clock I believe.
The old EMAC driver worked around that using some internal chip-specific
clock force bits that are different on various 44x implementations.
This is an attempt at doing it differently, by avoiding the reset when
there is no link, but forcing loopback mode instead. It seems to work
on my Taishan 440GX based board so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When using ZMII for MDIO only (such as 440GX with RGMII for data and ZMII for
MDIO), the ZMII code would fail to properly refcount, thus triggering a
BUG_ON().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This adds support for the Agere ET1011c PHY as found on the AMCC Taishan
board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds BCM5248 and Marvell 88E1111 PHY support to NEW EMAC driver.
These PHY chips are used on PowerPC 440EPx boards.
The PHY code is based on the previous work by Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
No need to convert to bytes and back - cleanup unneeded code.
Adapted from fix from 'Roel Kluin <12o3l@tiscali.nl>'
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
drivers/net/e1000/e1000_ethtool.c:113:
#define E1000_TEST_LEN sizeof(e1000_gstrings_test) / ETH_GSTRING_LEN
drivers/net/e1000e/ethtool.c:106:
#define E1000_TEST_LEN sizeof(e1000_gstrings_test) / ETH_GSTRING_LEN
E1000_TEST_LEN*ETH_GSTRING_LEN will expand to
sizeof(e1000_gstrings_test) / (ETH_GSTRING_LEN * ETH_GSTRING_LEN)
A lack of parentheses around defines causes unexpected results due to
operator precedences.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The bnx2x module depends on the zlib_inflate functions. The
build will fail if ZLIB_INFLATE has not been selected manually
or by building another module that automatically selects it.
Modify BNX2X config option to 'select ZLIB_INFLATE' like BNX2
and others. This seems to fix it.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update GPIO mapping for T3C.
Update xgmac for T3C support.
Fix typo in mtu table.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fixes a race condition in module unload. Without this change,
workqueue events may fire while bonding data structures are partially
freed but before bond_close() is invoked by unregister_netdevice().
Update version to 3.2.3.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add new hash for balance-xor and 802.3ad modes. Originally
submitted by "Glenn Griffin" <ggriffin.kernel@gmail.com>; modified by
Jay Vosburgh to move setting of hash policy out of line, tweak the
documentation update and add version update to 3.2.2.
Glenn's original comment follows:
Included is a patch for a new xmit_hash_policy for the bonding driver
that selects slaves based on MAC and IP information. This is a middle
ground between what currently exists in the layer2 only policy and the
layer3+4 policy. This policy strives to be fully 802.3ad compliant by
transmitting every packet of any particular flow over the same link.
As documented the layer3+4 policy is not fully compliant for extreme
cases such as ip fragmentation, so this policy is a nice compromise
for environments that require full compliance but desire more than the
layer2 only policy.
Signed-off-by: "Glenn Griffin" <ggriffin.kernel@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: David Sterba <dsterba@suse.cz>
Use macros for comparing jiffies. Jiffies' wrap caused missed events and hangs.
Module reinsert was needed to make bonding work again.
Signed-off-by: David Sterba <dsterba@suse.cz>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: Wagner Ferenc <wferi@niif.hu>
For consistency with the behaviour of the arp_ip_target option,
let /sys/class/net/bond0/bonding/xmit_hash_policy accept and report
current policy even if the bonding mode in effect does not use it.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: Wagner Ferenc <wferi@niif.hu>
Adhere to coding style: break line after the if condition
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: Wagner Ferenc <wferi@niif.hu>
Code for rendering multivalue sysfs files occurs three times
in this module. Rename 'buffer' to 'buf' in the first, for
the sake of consistency.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: Wagner Ferenc <wferi@niif.hu>
The previous code returned '\n' (that is, a single empty line)
from most files, with one exception (xmit_hash_policy), where
it returned 'NA\n'. This patch consolidates each file to return
nothing at all if not applicable, not even a '\n'.
I find this behaviour more usual, more useful, more efficient
and shorter to code from both sides.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: Wagner Ferenc <wferi@niif.hu>
Also remove trailing spaces from multivalued files.
This fixes output like for example:
$ od -c /sys/class/net/bond0/bonding/slaves
0000000 e t h - l e f t e t h - r i g
0000020 h t \n \0
0000025
It mostly entails deleting '+1'-s after sprintf() calls: the return value
of sprintf is the number of characters printed, without the closing NUL,
ie. exactly what the sysfs interface requires. The three multivalue
cases are different, because they also have to swallow back a trailing
space.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
ACPI: move timer broadcast before busmaster disable
clockevents: warn once when program_event() is called with negative expiry
hrtimers: avoid overflow for large relative timeouts
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: enable early use of sched_clock()
lockdep: make cli/sti annotation warnings clearer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] Fix wrong pt_regs in critical exception handler
[AVR32] Fix copy_to_user_page() breakage
[AVR32] Follow the rules when dealing with the OCD system
[AVR32] Clean up OCD register usage
[AVR32] Implement irqflags trace and lockdep support
[AVR32] Implement stacktrace support
[AVR32] Kconfig: Use def_bool instead of bool + default
[AVR32] Fix invalid status register bit definitions in asm/ptrace.h
[AVR32] Add TIF_RESTORE_SIGMASK to the work masks
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[AF_RXRPC]: Add a missing goto
[VLAN]: Lost rtnl_unlock() in vlan_ioctl()
[SCTP]: Fix the bind_addr info during migration.
[SCTP]: Add bind hash locking to the migrate code
[IPV4]: Remove prototype of ip_rt_advice
[IPv4]: Reply net unreachable ICMP message
[IPv6] SNMP: Increment OutNoRoutes when connecting to unreachable network
[BRIDGE]: Section fix.
[NIU]: Fix link LED handling.
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix memory controller register access when non-SMP.
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Fix led trigger locking bugs
|
|
The timer broadcast code might access HPET, which should not be
accessed after the busmaster disable.
In acpi_idle_enter_simple() this change also prevents, that we modify
the busmaster state without going actually idle. This might leave the
ACPI bm state in a stale state, when we leave the function early in
the need_resched() check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
|
|
The hrtimer problem with large relative timeouts resulting in a
negative expiry time went unnoticed as there is no check in the
clockevents_program_event() code. Put a check there with a WARN_ONCE
to avoid such problems in the future.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Relative hrtimers with a large timeout value might end up as negative
timer values, when the current time is added in hrtimer_start().
This in turn is causing the clockevents_set_next() function to set an
huge timeout and sleep for quite a long time when we have a clock
source which is capable of long sleeps like HPET. With PIT this almost
goes unnoticed as the maximum delta is ~27ms. The non-hrt/nohz code
sorts this out in the next timer interrupt, so we never noticed that
problem which has been there since the first day of hrtimers.
This bug became more apparent in 2.6.24 which activates HPET on more
hardware.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
some platforms have sched_clock() implementations that cannot be called
very early during wakeup. If it's called it might hang or crash in hard
to debug ways. So only call update_rq_clock() [which calls sched_clock()]
if sched_init() has already been called. (rq->idle is NULL before the
scheduler is initialized.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
make cli/sti annotation warnings easier to interpret.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
|
|
It's not like it really matters at this point since the system is
dying anyway, but handle_critical pushes too few registers on the
stack so the register dump, which makes the register dump look a bit
strange. This patch fixes it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
The current implementation of copy_to_user_page() gives "vaddr" to the
cache instruction when trying to sync the icache with the dcache. If
vaddr does not exist in the TLB, the CPU will silently abort the
operation, which may result in the caches staying out of sync.
To fix this, pass the "dst" parameter to flush_icache_range() instead
-- we know this is valid because we just wrote to it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
The current debug trap handling code does a number of things that are
illegal according to the AVR32 Architecture manual. Most importantly,
it may try to schedule from Debug Mode, thus clearing the D bit, which
can lead to "undefined behaviour".
It seems like this works in most cases, but several people have
observed somewhat unstable behaviour when debugging programs,
including soft lockups. So there's definitely something which is not
right with the existing code.
The new code will never schedule from Debug mode, it will always exit
Debug mode with a "retd" instruction, and if something not running in
Debug mode needs to do something debug-related (like doing a single
step), it will enter debug mode through a "breakpoint" instruction.
The monitor code will then return directly to user space, bypassing
its own saved registers if necessary (since we don't actually care
about the trapped context, only the one that came before.)
This adds three instructions to the common exception handling code,
including one branch. It does not touch super-hot paths like the TLB
miss handler.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Generate a new set of OCD register definitions in asm/ocd.h and rename
__mfdr() and __mtdr() to ocd_read() and ocd_write() respectively.
The bitfield definitions are a lot more complete now, and they are
entirely based on bit numbers, not masks. This is because OCD
registers are frequently accessed from assembly code, where bit
numbers are a lot more useful (can be fed directly to sbr, bfins,
etc.)
Bitfields that consist of more than one bit have two definitions:
_START, which indicates the number of the first bit, and _SIZE, which
indicates the number of bits. These directly correspond to the
parameters taken by the bfextu, bfexts and bfins instructions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
The 'H' bit is bit 29, while the 'R' bit doesn't exist. Luckily, we
don't actually use any of the bits in question.
Also update show_regs() to show the Debug Mask and Debug state bits.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
We really need to check TIF_RESTORE_SIGMASK before returning to
userspace. The existing code does not necessarily do this.
Define the work masks as a bitwise OR of the respective flags instead
of a hardcoded hex value to make it easier to spot errors like this in
the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Add a missing goto to error handling in the RXKAD security module for
AF_RXRPC.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
get_cpu() always returns zero on non-SMP builds, but we
really want the physical cpu number in this code in order
to do the right thing.
Based upon a non-SMP kernel boot failure report from Bernd Zeimetz.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SET_VLAN_NAME_TYPE_CMD command w/o CAP_NET_ADMIN capability
doesn't release the rtnl lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During accept/migrate the code attempts to copy the addresses from
the parent endpoint to the new endpoint. However, if the parent
was bound to a wildcard address, then we end up pointlessly copying
all of the current addresses on the system.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP accept code tries to add a newliy created socket
to a bind bucket without holding a lock. On a really
busy system, that can causes slab corruptions.
Add a lock around this code.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_rt_advice has been gone, so no need to keep prototype and debug message.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 stack doesn't reply any ICMP destination unreachable message
with net unreachable code when IP detagrams are being discarded
because of no route could be found in the forwarding path.
Incidentally, IPv6 stack replies such ICMPv6 message in the similar
situation.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert part of the led trigger core from rw spinlocks to rw
semaphores. We're calling functions which can sleep from invalid
contexts otherwise. Fixes bug #9264.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
|
|
IPv6 stack doesn't increment OutNoRoutes counter when IP datagrams
is being discarded because no route could be found to transmit them
to their destination. IPv6 stack should increment the counter.
Incidentally, IPv4 stack increments that counter in such situation.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARNING: vmlinux.o(.init.text+0x204e2): Section mismatch: reference to .exit.text:br_fdb_fini (between 'br_init' and 'br_fdb_init')
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LED in the current driver will not be controlled correctly. During
a link change the carrier of the link is not available and the LED
will never turn on.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
