aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-12-26gro: Fix potential use after freeHerbert Xu
The initial skb may have been freed after napi_gro_complete in napi_gro_receive if it was merged into an existing packet. Thus we cannot check same_flow (which indicates whether it was merged) after calling napi_gro_complete. This patch fixes this by saving the same_flow status before the call to napi_gro_complete. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: If AN is enabled, always read speed/duplex from the AN advertising bitsBen Hutchings
When AN is enabled and the link is down the speed/duplex control bits will not be meaningful. Use the advertising bits instead, and mask them with the LPA bits if and only if AN is complete (as before). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: When disabling the NIC, close the device rather than unregistering itBen Hutchings
This should reduce user confusion and may also aid recovery (ioctls will still be available). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: SFT9001: Add cable diagnosticsBen Hutchings
The SFT9001 firmware implements cable diagnostics; run those and include their results in a self-test. In case of a cable fault, do not fail the self-test as a whole; only faults in the NIC should cause that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Add support for multiple PHY self-testsBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Merge top-level functions for self-testsBen Hutchings
Pass in ethtool test flags to determine which tests to run. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Clean up PHY mode management in loopback self-testBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Fix unreliable link detection in some loopback modesBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sfc: Generate unique names for per-NIC workqueuesBen Hutchings
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26802.3ad: use standard ethhdr instead of ad_headerHolger Eitzenberger
802.3ad has its own ethhdr-like structure in the form of an ad_header, which is at the start of both the LACPDU and marker PDU. Both are the same from the struct values, both are packed as well. It's therefore perfectly fine to replace the ad_header by the ethhdr and to remove its definition. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26802.3ad: generalize out mac address initializerHolger Eitzenberger
Generalize out mac address initializer for the LACPDU multicast address and use in two places. Remove the now unused AD_MULTICAST_LACPDU_ADDR. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26802.3ad: initialize ports LACPDU from const initializerHolger Eitzenberger
Save some text by initializing ports LACPDU from const initializer, then get rid of ad_initialize_lacpdu(). Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26802.3ad: remove typedef around ad_systemHolger Eitzenberger
As typedefs are considered a bad thing most of the time remove the typedef around ad_system. Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26802.3ad: turn ports is_individual into a boolHolger Eitzenberger
Turn ports is_individual into a bool. There is no functional change. Signed-off-by: Holger Eitzenberger <heitzenberger@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26802.3ad: turn ports is_enabled into a boolHolger Eitzenberger
Turn ports is_enabled into a bool. There is no functional change. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26802.3ad: make ntt boolHolger Eitzenberger
Turn Need-To-Transmit port variable into a bool. There is no functional change. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26tracing/function-graph-tracer: strip ending newlines on commentsFrederic Weisbecker
Impact: tracer output improvement Ending newlines are appended automatically on comments by the function graph tracer because the newline needs to be placed after the "*/" comment characters. So if the user puts an ending newline, we want to strip it. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-12-26ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.Peter P Waskiewicz Jr
The adapter rings are kcalloc()'d, but in set_ringparam() in ixgbe_ethtool, we replace that memory from the vmalloc() pool. This can result in a NULL pointer reference when trying to modify the rings at a later time, or on device removal. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26ixgbe: Fix NAPI enable/disable path when using DCBPeter P Waskiewicz Jr
This change allows DCB mode to change the number of queues, and presumably the number of NAPI instances, safely. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26net: Init NAPI dev_list on napi_delPeter P Waskiewicz Jr
The recent GRO patches introduced the NAPI removal of devices in free_netdev. For drivers that can change the number of queues during driver operation, the NAPI infrastructure doesn't allow the freeing and re-addition of NAPI entities without reloading the driver. This change reinitializes the dev_list in each NAPI struct on delete, instead of just deleting it (and assigning the list pointers to POISON). Drivers that wish to remove/re-add NAPI will need to re-initialize the netdev napi_list after removing all NAPI instances, before re-adding NAPI devices again. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26igb: re-order queues to support cleaner use of ivar on 82576Alexander Duyck
The 82576 adapter orders the queues in pairs when virtualization is in use. The queue ordering previously conflicted with the ordering when sr-iov was enabled. This new ordering allows a PF to allocate 2 queues without using any VF resources. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26igb: defeature tx head writebackAlexander Duyck
This patch removes tx head writeback as it was found to not provide a significant improvement in tx performance and on some systems has been seen to cause a performance degredation due to partial cache line writes. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26ipsec: Remove useless ret variableHerbert Xu
This patch removes a useless ret variable from the IPv4 ESP/UDP decapsulation code. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26ucc_geth: Eliminate the need for forward referencesAnton Vorontsov
This patch simply reorders some functions to eliminate the need for forward references. No other changes than that. Suggested-by: Timur Tabi <timur@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26sysrq: fix ftrace help msg & doc.Randy Dunlap
Impact: update documentation and help messages We have a conventional method of explicitly stating the sysrq action key in a sysrq help message, so change dump-ftrace-buffer to use that method and add it to Documentation/sysrq.txt. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-12-26atm: Driver for Solos PCI ADSL2+ card.David Woodhouse
This adds basic support for the 'Solos' PCI ADSL2+ cards being developed by Traverse Technologies and Xrio Ltd: http://www.traverse.com.au/productview.php?product_id=116 Signed-off-by: Nathan Williams <nathan@traverse.com.au> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26gigaset: ifdef cleanupTilman Schmidt
Remove unnecessary #ifdef-s and #if-0-ed code sections. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26gigaset: use pr_err() and pr_info()Tilman Schmidt
Switch from private printk wrapper macros to using pr_err() and pr_info() from linux/kernel.h, at the same time unifying a few error messages. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26cxgb3: add control to access embedded imagesDivy Le Ray
Update contol path between cxgb3 and ULP modules (iWARP, iSCSI) to provide access to firware and protocol engine info. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wireless/prism54: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/wireless/prism54/islpci_hotplug.c:97:1: warning: symbol 'prism54_probe' was not declared. Should it be static? drivers/net/wireless/prism54/islpci_hotplug.c:220:1: warning: symbol 'prism54_remove' was not declared. Should it be static? drivers/net/wireless/prism54/islpci_hotplug.c:263:1: warning: symbol 'prism54_suspend' was not declared. Should it be static? drivers/net/wireless/prism54/islpci_hotplug.c:286:1: warning: symbol 'prism54_resume' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wireless/ipw2x00: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/wireless/ipw2x00/ipw2100.c:5271:6: warning: symbol 'ipw2100_queues_initialize' was not declared. Should it be static? drivers/net/wireless/ipw2x00/ipw2100.c:5278:6: warning: symbol 'ipw2100_queues_free' was not declared. Should it be static? drivers/net/wireless/ipw2x00/ipw2100.c:5285:5: warning: symbol 'ipw2100_queues_allocate' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wireless/b43: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/wireless/b43/phy_a.c:80:6: warning: symbol 'b43_radio_set_tx_iq' was not declared. Should it be static? drivers/net/wireless/b43/phy_a.c:150:6: warning: symbol 'b43_radio_init2060' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:57:10: warning: symbol 'b43_radio_channel_codes_bg' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:218:6: warning: symbol 'b43_set_txpower_g' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:386:6: warning: symbol 'b43_nrssi_hw_write' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:393:5: warning: symbol 'b43_nrssi_hw_read' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:404:6: warning: symbol 'b43_nrssi_hw_update' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:418:6: warning: symbol 'b43_nrssi_mem_update' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:592:6: warning: symbol 'b43_calc_nrssi_slope' was not declared. Should it be static? drivers/net/wireless/b43/phy_g.c:1357:5: warning: symbol 'b43_radio_init2050' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wireless/ath9k: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/wireless/ath9k/eeprom.c:195:6: warning: symbol 'ath9k_fill_eeprom' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:463:5: warning: symbol 'ath9k_check_eeprom' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:1219:6: warning: symbol 'ath9k_hw_set_def_power_per_rate_table' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:1510:6: warning: symbol 'ath9k_hw_set_4k_power_per_rate_table' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2007:5: warning: symbol 'ath9k_set_txpower' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2106:6: warning: symbol 'ath9k_set_addac' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2543:6: warning: symbol 'ath9k_eeprom_set_board_values' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2606:5: warning: symbol 'ath9k_get_eeprom_antenna_cfg' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2622:4: warning: symbol 'ath9k_hw_get_4k_num_ant_config' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2628:4: warning: symbol 'ath9k_hw_get_def_num_ant_config' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2647:4: warning: symbol 'ath9k_get_num_ant_config' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2790:5: warning: symbol 'ath9k_get_eeprom' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wireless: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/wireless/airo.c:3610:6: warning: symbol 'mpi_receive_802_11' was not declared. Should it be static? drivers/net/wireless/atmel.c:3183:6: warning: symbol 'atmel_join_bss' was not declared. Should it be static? drivers/net/wireless/ray_cs.c:831:5: warning: symbol 'ray_dev_init' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wan/z85230.c: fix sparse warnings: un-EXPORT symbolsHannes Eder
The symbols are only references within the translation unit they are defined in, so un-EXPORT them und make them 'static'. Fix this sparse warnings: drivers/net/wan/z85230.c:604:25: warning: symbol 'z8530_dma_sync' was not declared. Should it be static? drivers/net/wan/z85230.c:613:25: warning: symbol 'z8530_txdma_sync' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wan: fix sparse warning: make symbol staticHannes Eder
Fix this sparse warning: drivers/net/wan/x25_asy.c:623:5: warning: symbol 'x25_asy_esc' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/wan: fix sparse warnings: make do-while a compound statementHannes Eder
Fix this sparse warnings: drivers/net/wan/wanxl.c:414:3: warning: do-while statement is not a compound statement drivers/net/wan/wanxl.c:441:3: warning: do-while statement is not a compound statement Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/tulip: fix sparse warnings: make do-while a compound statementHannes Eder
Fix this sparse warnings: drivers/net/tulip/de2104x.c:1695:4: warning: do-while statement is not a compound statement drivers/net/tulip/tulip_core.c:1433:5: warning: do-while statement is not a compound statement Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/tokenring: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/tokenring/ibmtr.c:1840:6: warning: symbol 'tok_rerun' was not declared. Should it be static? drivers/net/tokenring/madgemc.c:469:16: warning: symbol 'madgemc_setnselout_pins' was not declared. Should it be static? drivers/net/tokenring/proteon.c:286:16: warning: symbol 'proteon_setnselout_pins' was not declared. Should it be static? drivers/net/tokenring/skisa.c:303:16: warning: symbol 'sk_isa_setnselout_pins' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/skfp: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/skfp/skfddi.c:620:13: warning: symbol 'skfp_interrupt' was not declared. Should it be static? drivers/net/skfp/skfddi.c:687:25: warning: symbol 'skfp_ctl_get_stats' was not declared. Should it be static? drivers/net/skfp/skfddi.c:1232:6: warning: symbol 'CheckSourceAddress' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/qlge: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/qlge/qlge_ethtool.c:100:6: warning: symbol 'ql_update_stats' was not declared. Should it be static? drivers/net/qlge/qlge_mpi.c:22:5: warning: symbol 'ql_get_mb_sts' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/netxen: fix sparse warnings: use NULL pointer instead of plain ↵Hannes Eder
integer Fix this sparse warnings: drivers/net/netxen/netxen_nic_hw.c:1462:18: warning: Using plain integer as NULL pointer drivers/net/netxen/netxen_nic_hw.c:1536:18: warning: Using plain integer as NULL pointer Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/ixgbe: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/ixgbe/ixgbe_82598.c:180:5: warning: symbol 'ixgbe_get_copper_link_capabilities_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:245:5: warning: symbol 'ixgbe_setup_fc_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:729:5: warning: symbol 'ixgbe_set_vmdq_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:773:5: warning: symbol 'ixgbe_set_vfta_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:897:5: warning: symbol 'ixgbe_read_analog_reg8_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:919:5: warning: symbol 'ixgbe_write_analog_reg8_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:940:5: warning: symbol 'ixgbe_read_i2c_eeprom_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_82598.c:1000:5: warning: symbol 'ixgbe_get_supported_physical_layer_82598' was not declared. Should it be static? drivers/net/ixgbe/ixgbe_dcb_82598.c:100:5: warning: symbol 'ixgbe_dcb_config_packet_buffers_82598' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/irda: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/irda/ma600-sir.c:239:5: warning: symbol 'ma600_reset' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:875:5: warning: symbol 'smsc_ircc_hard_xmit_sir' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:1131:6: warning: symbol 'smsc_ircc_set_sir_speed' was not declared. Should it be static? drivers/net/irda/smsc-ircc2.c:1897:6: warning: symbol 'smsc_ircc_sir_start' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:150:5: warning: symbol 'w83977af_open' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:313:5: warning: symbol 'w83977af_probe' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:412:6: warning: symbol 'w83977af_change_speed' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:492:5: warning: symbol 'w83977af_hard_xmit' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:734:5: warning: symbol 'w83977af_dma_receive' was not declared. Should it be static? drivers/net/irda/w83977af_ir.c:806:5: warning: symbol 'w83977af_dma_receive_complete' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/igb: remove dead code (function 'igb_read_pci_cfg')Hannes Eder
Fix this warning: drivers/net/igb/e1000_mac.c:54: warning: 'igb_read_pci_cfg' defined but not used Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/enic: fix sparse warning: make symbol staticHannes Eder
Fix this sparse warning: drivers/net/enic/vnic_dev.c:288:5: warning: symbol 'vnic_dev_capable' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26drivers/net/e1000e: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/e1000e/es2lan.c:1265:5: warning: symbol 'e1000_read_kmrn_reg_80003es2lan' was not declared. Should it be static? drivers/net/e1000e/es2lan.c:1298:5: warning: symbol 'e1000_write_kmrn_reg_80003es2lan' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25drivers/net/cxgb3: comment out dead codeHannes Eder
The function 'vsc8211_set_speed_duplex' is not used, so comment it out. For 'vsc8211_set_automdi' the function 'vsc8211_set_speed_duplex' is the only caller, so comment it out as well. Fix this (sparse) warning: drivers/net/cxgb3/vsc8211.c:269: warning: 'vsc8211_set_automdi' defined but not used drivers/net/cxgb3/vsc8211.c:295:5: warning: symbol 'vsc8211_set_speed_duplex' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25drivers/net/bonding: fix sparse warnings: move decls to header fileHannes Eder
Fix this sparse warnings: drivers/net/bonding/bond_main.c:104:20: warning: symbol 'bonding_defaults' was not declared. Should it be static? drivers/net/bonding/bond_main.c:204:22: warning: symbol 'ad_select_tbl' was not declared. Should it be static? drivers/net/bonding/bond_sysfs.c:60:21: warning: symbol 'bonding_rwsem' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-25drivers/net/atlx: fix sparse warnings: make symbols staticHannes Eder
Fix this sparse warnings: drivers/net/atlx/atl1.c:198:16: warning: symbol 'atl1_check_options' was not declared. Should it be static? drivers/net/atlx/atl1.c:526:5: warning: symbol 'atl1_read_mac_addr' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 04:19:30 +0000