| Age | Commit message (Collapse) | Author |
|---|
|
According to the datasheet, Intel 82371MX (MPIIX) actually has only a
single IDE channel mapped to the primary or secondary ports depending on
the value of the bit 14 of the IDETIM register at PCI config. offset 0x6C
(the register at 0x6F which the driver refers to. doesn't exist). So,
disguise the controller as dual channel and set enablebits masks/values
such that only either primary or secondary channel is detected enabled.
Also, preclude the IDE probing code from reading PCI BARs, this controller
just doesn't have them (it's not the separate PCI function like the other
PCI controllers), it only decodes the legacy addresses.
[ Alan sayeth " MPIIX does not work with or without the change. It needs its
own different driver and not to use setup-pci. Huge job and since it works
well with libata who cares. Ditto the early PIIX chip." ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix minor coding mistake in the HPT36x PCI clock detection code noticed by
Bartlomiej Zolnierkiewicz -- it always reported 33 MHz due to the missing
'break' statements. This, however, most probably never mattered -- in fact, I
was thinking of removing the 25/40 MHz cases completely since HPT36x BIOSes
didn't seem to set any other value than 7 into the 'cmd_high_time' field, i.e.
supported only 33 MHz PCI.
Note that in the original driver there was another bug: 25 and 40 MHz cases
were interchanged. Since the 'cmd_high_time' field is in units of PCI clocks,
a lower clock count just *cannot* correspond to a higher frequency, i. e. it
should be 5 for 25 MHz PCI and 9 for 40 MHz PCI, not the other way around.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Finally, rework the driver init. code to correctly handle all the chip
variants HighPoint has created so far. This should cure the rest of the
timing issues in the driver (especially, on 66 MHz PCI) caused by the
HighPoint's habit of switching the base DPLL clock with every new revision
of the chips...
- switch to using the enumeration type to differ between the numerous chip
variants, matching PCI device/revision ID with the chip type early, at the
init_setup stage;
- extend the hpt_info structure to hold the DPLL and PCI clock frequencies,
stop duplicating it for each channel by storing the pointer in the pci_dev
structure: first, at the init_setup stage, point it to a static "template"
with only the chip type and its specific base DPLL frequency, the highest
supported DMA mode, and the chip settings table pointer filled, then, at
the init_chipset stage, allocate per-chip instance and fill it with the
rest of the necessary information;
- get rid of the constant thresholds in the HPT37x PCI clock detection code,
switch to calculating PCI clock frequency based on the chip's base DPLL
frequency;
- switch to using the DPLL clock and enable UltraATA/133 mode by default on
anything newer than HPT370/A;
- fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
unify the HPT36x/37x setup code and the speedproc handlers by joining the
register setting lists into the table indexed by the clock selected;
- add enablebits for all the chips to avoid touching disabled channels
(though the HighPoint BIOS seem to only disable the primary one on
HPT371/N);
- separate the UltraDMA and MWDMA masks there to avoid changing PIO timings
when setting an UltraDMA mode in hpt37x_tune_chipset().
This version has been tested on HPT370/302/371N.
Thanks to Alan for the inspiration. Hopefully, his libata driver will also
benefit from the work done on this "obsolete" driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Clean up DMA timeout handling for HPT370:
- hpt370_lostirq_timeout() cleared the DMA status which made __ide_dma_end()
called afterwards return the incorrect result, and the DMA engine was reset
both before and after stopping DMA while the HighPoint drivers only do it
after (which seems logical) -- fix this and also rename the function;
- get rid of the needless mutual recursion in hpt370_ide_dma_end() and
hpt370_ide_dma_timeout();
- get rid of hpt370_lostirq_timeout() since hwif->ide_dma_end() called from
the driver's interrupt handler later does all its work.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Continue with the driver rewrite:
- move the interrupt twiddling code from the speedproc handlers into the
init_hwif_hpt366 which allows to merge the two HPT37x speedproc handlers
into one;
- get rid of in init_hpt366 which solely consists of the duplicate code, then
fold init_hpt37x() into init_chipset_hpt366();
- fix hpt3xx_tune_drive() to always set the PIO mode requested, not the best
possible one, change hpt366_config_drive_xfer_rate() accordingly, simplify
it a bit;
- group all the DMA related code together init_hwif_hpt366(), and generally
clean up and beautify it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Begin the real driver redesign. For the starters:
- cache the offset of the IDE channel's MISC. control registers which are used
throughout the driver in hwif->select_data;
- only touch the relevant MCR when detecting the cable type on HPT374's
function 1;
- make HPT36x's speedproc handler look the same way as HPT37x ones; fix the
PIO timing register mask for HPT37x.
- rename all the HPT3xx register related variables consistently; clean up the
whitespace.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Switch to using pci_get_slot() to get to the function 1 of HPT36x/374 chips --
there's no need for the driver itself to walk the list of the PCI devices, and
it also forgets to check the bus number of the device found.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
- Rework the driver setup code so that it prefixes the driver startup
messages with the real chip name.
- Print the measured f_CNT value and the DPLL setting for non-HPT3xx
chips as well.
- Claim the extra 240 bytes of I/O space for all chips, not only for
those having PCI device ID of 0x0004.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
- Rework hpt3xx_ratemask() and hpt3xx_ratefilter() so that the former
returns the max. mode computed at the load time and doesn't have to do
bad Ultra33 drive list lookups anymore; remove the duplicate code from
the latter function. Move the quirky drive list lookup into
hpt3xx_quirkproc() where it should have been from the start...
- Disable UltraATA/100 for HPT370 by default as the 33 MHz ATA clock
being used does not allow for it, and this *greatly* increases the
transfer speed.
- Save some space by using byte-wide fields in struct hpt_info; switch to
reading the 8-bit PCI revision ID reg. only, not the whole 32-bit reg.
- Start incrementing the driver version number with each patch (should
have been done from the first one posted).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (27 commits)
[IA64] swiotlb abstraction (e.g. for Xen)
[IA64] swiotlb cleanup
[IA64] make swiotlb use bus_to_virt/virt_to_bus
[IA64] swiotlb bug fixes
[IA64] Hook up getcpu system call for IA64
[IA64] clean up sparsemem memory_present call
[IA64] show_mem() for IA64 sparsemem NUMA
[IA64] missing exports hwsw_sync_...
[IA64] virt_to_page() can be called with NULL arg
[IA64] alignment bug in ldscript
[IA64] register memory ranges in a consistent manner
[IA64] Enable SWIOTLB only when needed
[IA64-SGI] Check for TIO errors on shub2 Altix
[IA64] remove bogus prototype ia64_esi_init()
[IA64] Clear IRQ affinity when unregistered
[IA64] fix ACPI Kconfig issues
[IA64] Fix NULL-pointer dereference in ia64_machine_kexec()
[IA64] find thread for user rbs address
[IA64] use snprintf() on features field of /proc/cpuinfo
[IA64] enable singlestep on system call
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: ocfs2_link() journal credits update
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
USB HID: handle multi-interface devices for Apple macbook pro properly
HID: move away from DEBUG defines in favor of CONFIG_HID_DEBUG
USB HID: fix bogus comment in hid_get_class_descriptor()
USB HID: remove hid_find_field_by_usage()
HID: API - fix leftovers of hidinput API in USB HID
HID: hid debug from hid-debug.h to hid layer
hid: force feedback driver for PantherLord USB/PS2 2in1 Adapter
hid: quirk for multi-input devices with unneeded output reports
hid: allow force feedback for multi-input devices
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Remove obsolete prototypes
IB/ehca: Remove use of do_mmap()
RDMA/addr: Handle ethernet neighbour updates during route resolution
IB: Make sure struct ib_user_mad.data is aligned
IB/srp: Don't wait for response when QP is in error state.
IB: Return qp pointer as part of ib_wc
IB: Include <linux/kref.h> explicitly in <rdma/ib_verbs.h>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (32 commits)
mmc: tifm: replace kmap with page_address
mmc: sdhci: fix voltage ocr
mmc: sdhci: replace kmap with page_address
mmc: wbsd: replace kmap with page_address
mmc: handle pci_enable_device() return value in sdhci
mmc: Proper unclaim in mmc_block
mmc: change wbsd mailing list
mmc: Graceful fallback for fancy features
mmc: Handle wbsd's stupid command list
mmc: Allow host drivers to specify max block count
mmc: Allow host drivers to specify a max block size
tifm_sd: add suspend and resume functionality
tifm_core: add suspend/resume infrastructure for tifm devices
tifm_7xx1: prettify
tifm_7xx1: recognize device 0xac8f as supported
tifm_7xx1: switch from workqueue to kthread
tifm_7xx1: Merge media insert and media remove functions
tifm_7xx1: simplify eject function
Add dummy_signal_irq function to save check in ISR
Remove unused return value from signal_irq callback
...
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (37 commits)
[S390] Avoid excessive inlining.
[S390] Mark kernel text section read-only.
[S390] Convert memory detection into C code.
[S390] Calibrate delay and bogomips.
[S390] Hypervisor filesystem (s390_hypfs) for z/VM
[S390] Add crypto support for 3592 tape devices
[S390] boot from NSS support
[S390] Support for s390 Pseudo Random Number Generator
[S390] ETR support.
[S390] noexec protection
[S390] move crypto options and some cleanup.
[S390] cio: Don't spam debug feature.
[S390] Cleanup of CHSC event handling.
[S390] cio: declare hardware structures packed.
[S390] Add set_fs(USER_DS) to start_thread().
[S390] cio: Catch operand exceptions on stsch.
[S390] Fix register usage description.
[S390] kretprobe_trampoline_holder() in wrong section.
[S390] Fix kprobes breakpoint handling.
[S390] Update maintainers file.
...
|
|
Fix the key serial number collision avoidance code in key_alloc_serial().
This didn't use to be so much of a problem as the key serial numbers were
allocated from a simple incremental counter, and it would have to go through
two billion keys before it could possibly encounter a collision. However, now
that random numbers are used instead, collisions are much more likely.
This is fixed by finding a hole in the rbtree where the next unused serial
number ought to be and using that by going almost back to the top of the
insertion routine and redoing the insertion with the new serial number rather
than trying to be clever and attempting to work out the insertion point
pointer directly.
This fixes kernel BZ #7727.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Minor cleanup
[CIFS] Missing free in error path
[CIFS] Reduce cifs stack space usage
[CIFS] lseek polling returned stale EOF
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (40 commits)
[MIPS] Yosemite: Fix missing parens in SERIAL_READ_1 macro
[MIPS] Fix warnings in run_uncached on 32bit kernel
[MIPS] Comment fix
[MIPS] MT: Nuke duplicate mips_mt_regdump() prototype.
[MIPS] Alchemy: Fix PCI-memory access
[MIPS] Move .set reorder out of conditional code
[MIPS] Check FCSR for pending interrupts before restoring from a context.
[MIPS] Jaguar ATX: Fix large number of warnings.
[MIPS] Jaguar: Fix MAC address detection after platform_device conversion.
[MIPS] SMTC: Make a bunch of functions and variables static.
[MIPS] Use compat_sys_pselect6
[MIPS] SMTC: Cleanup idle hook invocation.
[MIPS] SELinux: Add security hooks to mips-mt {get,set}affinity
[MIPS] IRIX: Linux coding style cleanups.
[MIPS] PB1100: Fix pile of warnings
[MIPS] Alchemy: Fix bunch of warnings
[MIPS] Whitespace cleanups.
[MIPS] Alchemy: Fix bunch more warnings.
[MIPS] Use ARRAY_SIZE macro when appropriate
[MIPS] Fix some whitespace damage
...
|
|
Tildes as in path as in filenames are handled correctly now:
only files, containing tilde '~', are backups, thus are not valid.
[KJ]:
Definition of `space' was removed, scripts/Kbuild.include has one.
That definition was taken right from the GNU make manual, while Kbuild's
version is original.
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Bastian Blank <bastian@waldi.eu.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Oleg Verych <olecom@flower.upol.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
GNU binutils, root users, tmpfiles, external modules ro builds must
be fixed to do the right thing now.
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Horst Schirmeier <horst@schirmeier.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Oleg Verych <olecom@flower.upol.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replacing overhead of using some (external) programs
instead of good old `sh'.
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: William Stearns <wstearns@pobox.com>
Cc: Martin Schlemmer <azarah@nosferatu.za.org>
Signed-off-by: Oleg Verych <olecom@flower.upol.cz>
Acked-by: Mark Lord <lkml@rtr.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Missing tab. Missing entry in changelog
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
arch/mips/lib/uncached.c: In function 'run_uncached':
arch/mips/lib/uncached.c:47: warning: comparison is always true due to limited range of data type
arch/mips/lib/uncached.c:48: warning: comparison is always false due to limited range of data type
arch/mips/lib/uncached.c:57: warning: comparison is always true due to limited range of data type
arch/mips/lib/uncached.c:58: warning: comparison is always false due to limited range of data type
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The problem was introduced in 2.6.18.3 with the casting of some
36bit-defines (PCI memory) in au1000.h to resource_size_t which may be
u32 or u64 depending on the experimental CONFIG_RESOURCES_64BIT.
With unset CONFIG_RESOURCES_64BIT, the pci-memory cannot be accessed
because the ioremap in arch/mips/au1000/common/pci.c already used the
truncated addresses.
With set CONFIG_RESOURCES_64BIT, things get even worse, because PCI-scan
aborts, due to resource conflict: request_resource() in arch/mips/pci/pci.c
fails because the maximum iomem-address is 0xffffffff (32bit) but the
pci-memory-start-address is 0x440000000 (36bit).
To get pci working again, I propose the following patch:
1. remove the resource_size_t-casting from au1000.h again
2. make the casting in arch/mips/au1000/common/pci.c (it's allowed and
necessary here. The 36bit-handling will be done in __fixup_bigphys_addr).
With this patch pci works again like in 2.6.18.2, the gcc-compile warnings
in pci.c are gone and it doesn't depend on CONFIG_EXPERIMENTAL.
Signed-off-by: Alexander Bigga <ab@mycable.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The N32 and O32 pselect6 syscalls need to use compat_sys_pselect6 to
translate arguments from 32-bit to 64-bit layout.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch adds LSM hooks into the setaffinity and getaffinity functions
for the mips architecture to enable security modules to control these
operations between tasks with different security attributes. This
implementation uses the existing task_setscheduler and task_getscheduler
LSM hooks.
Signed-Off-By: David Quigley <dpquigl@tycho.nsa.gov>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CC arch/mips/au1000/pb1100/board_setup.o
arch/mips/au1000/pb1100/board_setup.c: In function ‘board_setup’:
arch/mips/au1000/pb1100/board_setup.c:104: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:105: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:105: warning: passing argument 2 of ‘writeb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:109: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:110: warning: passing argument 1 of ‘readb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:110: warning: passing argument 2 of ‘writeb’ makes pointer from integer without a cast
arch/mips/au1000/pb1100/board_setup.c:51: warning: unused variable ‘sys_clksrc’
arch/mips/au1000/pb1100/board_setup.c:51: warning: unused variable ‘sys_freqctrl’
arch/mips/au1000/pb1100/board_setup.c:50: warning: unused variable ‘pin_func’
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
CC arch/mips/au1000/common/pci.o
arch/mips/au1000/common/pci.c:42: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:43: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:49: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c:50: warning: large integer implicitly truncated to unsigned type
arch/mips/au1000/common/pci.c: In function ‘au1x_pci_setup’:
arch/mips/au1000/common/pci.c:82: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
early_serial_setup is only defined when CONFIG_SERIAL_8250 is set.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
pb1200/irqmap.c had been broken a while due to non-named initializer
and had missed some recent IRQ related changes. Apply these commits
to this file.
[MIPS] IRQ cleanups
commit 1603b5aca4f15b34848fb5594d0c7b6333b99144
[MIPS] use generic_handle_irq, handle_level_irq, handle_percpu_irq
commit 1417836e81c0ab8f5a0bfeafa90d3eaa41b2a067
[MIPS] Compile __do_IRQ() when really needed
commit e77c232cfc6e1250b2916a7c69225d6634d05a49
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Oprofile cannot work on SMTC due to the limited number of counters.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Given that the Makefiles involved already have conditional compilation of
the form:
obj-$(CONFIG_KGDB) += dbg_io.o
there seems to be little value for the dbg_io.c source files to check
that config variable yet again.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This get rid of some undesirable hole in BSS section due to random
order of placement.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
