Age | Commit message (Collapse) | Author |
|
If we build a kernel without gta01/gta02 the
machine_is_ macro will expand to (0) and the compiler will
optimize the if (0) {} away.
Signed-Off-By: Holger Freyther <zecke@openmoko.org>
|
|
Signed-Off-By: Holger Freyther <zecke@openmoko.org>
|
|
Headphone jack detection is bouncy, it can trigger multiple interrupts
on insertion or removal. This patch adds a workqueue that waits out the
interrupt spew in 100ms units, and if it sees no more interrupts for 100ms
only then samples and reports the jack state. I was unable to get a bounce
after 20 or so tries after this.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Glamo "cmd mode" is modal, but nothing took care about locking.
Also cmd mode was entered recursively in rotate_lcd().
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
loglevl=9 can cause failure to init glamo-fb
problem seems to be too low timeout when text scrolling can
delay commandqueue going empty
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Only enable or disable the interrupt if we see we are in the opposing state.
Also force that damn GSM download signal deasserted on probe at the time we
set the logical state for it to deasserted.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Add in some audio config needed
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
see
http://bugzilla.openmoko.org/cgi-bin/bugzilla/show_bug.cgi?id=1288
|
|
Similar to the neo1974_pm_gsm.c keep a static struct around. On suspend
we will save the current power state, on resume we will use this
information to enable power of the GPS only when it was powered on before.
This is passing basic tests with screen /dev/ttySAC1 on suspend and resume.
Only do this for the GTA02 as I don't have a gllin setup for the GTA01
I wonder why the suspend and resume code is not using gps_pwron_set and why
for the GTA02 we need to keep the state of the GPIOs, this should be done
by the s3c code.
Signed-Off-by: Holger Frether <zecke@openmoko.org>
|
|
GTA02_GPIO_nDL_GSM defaults to high/1. On resume do not enable the DL_GSM if
it was not enabled before. This is stopping the storm of interrupts.
Fix the logic in the download file handling. Downloads are disabled (0) when
the GTA02_GPIO_nDL_GSM is high (1). To enable downloading set
GTA02_GPIO_nDL_GSM to low (0, !on). Disable the jack interrupt while download
the is active. When disabling download we will get a couple of jack interrupts
but this is hardly avoidable.
Avoid reading the GPIO value if we do not even have a console set.
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
Samsung SoC
Use this irq_to_gpio in the neo1973 keyboard driver
|
|
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
GTA01_GPIO_AUX_KEY looks odd.
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
From: Andy Green <andy@openmoko.com>
Sigend-off-by: Andy Green <andy@openmoko.com>
|
|
Add function
int gta02_get_pcb_revision(void)
which returns state of GTA02 PCB revision pins. It is also called
and logged during boot with KERN_INFO. The results look like:
b9 b8 b2 b1 b0
GPD4 GPD3 GPD0 GPC15 GPC13
GTA02 A5 and before: 0x000
GTA02 A6 : 0x001
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Hey,
I see no reason to send LL debugging messages to the modem. This can happen if
we compile the Samsung SoC with PM debugging as in andy's git branch.
From 452c17990dfeb9c2eb2ffa7ded4d24ddb1bcd4b2 Mon Sep 17 00:00:00 2001
From: Holger Freyther <zecke@openmoko.org>
Date: Sun, 23 Mar 2008 00:57:28 +0100
Subject: [PATCH] Never ever send debug messages to the modem. The serial
console is
on UART2, send the messages for decompressing and low level debugging
there.
Signed-Off-by: Holger Freyther <zecke@openmoko.org>
|
|
We used to drive output high into GPS unit in suspend
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Add platform stuff to deal with going in and out of suspend
so the motion sensor IO is not driving high into unpowered sensors
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Hey,
the legacy application 'atd' from Russ Nelson/Nils Faerber, used by Qtopia, to
schedule alarms currently fails to start as the the above ioctl is failing.
The other drivers in drivers/rtc implement the above ioctl and we can
implement it too.
The code to mask/unmask the RTC alarm is copied from the set_alarm routine and
adapted to use the reg_set_bit_mask and reg_set_clear_mask.
It is compiling, so it must work. Please welcome me the lkml way ;)
Signed-Off-by: Holger Hans Peter Freyther <zecke@openmoko.org>
|
|
We don't take care to stop driving generated USB host power even
when we have a 1A charger connected on the same pins.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Unless I really really missed the point, there is no support for enabling
USB Host power for USB host mode. This patch adds a /sys node for GTA02
that allows control of the charge pump for 5V out on the USB mini connector
It doesn't change any logical mode in the CPU, just enables (1) and disables
(0) USB host power.
# cat /sys/devices/platform/neo1973-pm-host.0/hostmode
0
# echo 1 > /sys/devices/platform/neo1973-pm-host.0/hostmode
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Starting up all the PWMs seems to be needed for PWM3 operation
and FIQ / HDQ / VIB operation. But after starting, turn the
LEDs to GPIO-only.
Applies on top of Willie's patch
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
|
|
|
|
We need to be able to use the config option CONFIG_MMC_UNSAFE_RESUME that allows the rootfs
to live on SD. But when we use this, it tries to send a reset command to the SD card during
suspend -- and unfortunately many things like Power have suspended by then.
This patch again rejects IO on the MMC device during suspend of the MMC device, and it
gives the result the rootfs on SD card works okay.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
|
|
Add support for GPA[] GPIO bus since we have some NCs
but they seem to output-only IO cells so no matter
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This is a driver for the bq27000 found in the Highcell A5
battery, and the platform device stuff for it for GTA02. It
is a Power Supply Class battery device.
The driver doesn't contain an HDQ engine but accepts pointers
from the platform data to the HDQ action routines; our
platform data plugs it into the FIQ HDQ engine stuff.
The Power Supply class exposes the battery down /sys so you
can find out battery status by doing the equivalent of this
bash command
for i in capacity charge_full current_now present status technology temp time_to_empty_now time_to_full_now type voltage_now ; do echo -n "$i " ; cat /sys/devices/platform/bq27000-battery.0/power_supply/bat/$i ; done
Here is the kind of result you get from a battery discharging
capacity 0
charge_full 1215585
current_now 183375
present 1
status Discharging
technology Li-ion
temp 276
time_to_empty_now 0
time_to_full_now 3932100
type Battery
voltage_now 2761000
Note that temp is in 1/10 degrees C, other values are in uV,
uA, uW. The time_to_* reported are bogus, but that is what
the battery actually reports.
We can make more mappings to entries in power_supply class
but this is enough to get started with.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This adds a platform driver and device which performs HDQ
battery protocol using a single GPIO pin which is set
through platform data.
HDQ has some hard latency requirements which can't
be met if interrupts are enabled, so normally using
a GPIO for this will require blocking out all other
interrupts and processes for several milliseconds
per register being read or written.
This HDQ protocol engine is a FSM implemented inside the
the FIQ ISR and regulated by timer interrupts happening
at 20us intervals. The path through the FSM on any
"clock" is very short and should be over with in ~
1us. Because FIQ has guaranteed latencies of <1us,
it means we can service the HDQ protocol without
blocking interrupts or any other process other than
the caller that is waiting for the result. It's pretty
cool performance from 1 GPIO ;-)
Due to it being hard to do locking from the FIQ ISR
the code simply sleeps 10ms or whatever the scheduler
gives it and checks if the transfer took place yet.
This platform driver doesn't have any knowledge about
the device it is talking to, it just knows it is a
HDQ device. It exports three functions for read, write
and confirming HDQ is initialized. It also exports two
/sys nodes that are usable by humans, one dumps the whole
127 register HDQ register space
# cat /sys/devices/platform/gta02-hdq.0/hdq/dump
00 44 55 00 00 00 ba 04 a2 0d 50 00 00 00 00 00
00 00 9a 1a 00 00 ff ff ff ff 29 00 00 00 80 2b
00 00 00 00 00 00 ff ff 00 00 00 00 00 32 af 06
a0 d8 37 4e 00 00 00 00 00 00 00 34 2e 03 b4 e7
00 00 06 00 41 00 4c 02 00 00 00 00 00 00 00 00
83 02 00 00 94 09 59 b9 a5 0d 7f 21 00 00 7a ff
df ff 62 ff a7 04 2e 05 00 00 00 01 00 07 00 00
2a 78 36 67 7b b5 1b a9 af 19 38 89 63 57 42 7c
#
and the other allows to set one register
# echo 2 170 > /sys/devices/platform/gta02-hdq.0/hdq/write
writes 0xAA into register 2.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
These are initialized already
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
--- linux-2.6.22/drivers/i2c/chips/pcf50606.c.orig 2008-01-17 22:30:16.000000000 -0800
+++ linux-2.6.22/drivers/i2c/chips/pcf50606.c 2008-01-17 22:31:43.000000000 -0800
@@ -71,12 +71,19 @@
I2C_CLIENT_INSMOD_1(pcf50606);
-#define PCF50606_F_CHG_FAST 0x00000001 /* Charger Fast allowed */
-#define PCF50606_F_CHG_PRESENT 0x00000002 /* Charger present */
-#define PCF50606_F_CHG_FOK 0x00000004 /* Fast OK for battery */
-#define PCF50606_F_CHG_ERR 0x00000008 /* Charger Error */
-#define PCF50606_F_CHG_PROT 0x00000010 /* Charger Protection */
-#define PCF50606_F_CHG_READY 0x00000020 /* Charging completed */
+#define PCF50606_B_CHG_FAST 0 /* Charger Fast allowed */
+#define PCF50606_B_CHG_PRESENT 1 /* Charger present */
+#define PCF50606_B_CHG_FOK 2 /* Fast OK for battery */
+#define PCF50606_B_CHG_ERR 3 /* Charger Error */
+#define PCF50606_B_CHG_PROT 4 /* Charger Protection */
+#define PCF50606_B_CHG_READY 5 /* Charging completed */
+
+#define PCF50606_F_CHG_FAST (1<<PCF50606_B_CHG_FAST) /* Charger Fast allowed */
+#define PCF50606_F_CHG_PRESENT (1<<PCF50606_B_CHG_PRESENT) /* Charger present */
+#define PCF50606_F_CHG_FOK (1<<PCF50606_B_CHG_FOK) /* Fast OK for battery */
+#define PCF50606_F_CHG_ERR (1<<PCF50606_B_CHG_ERR) /* Charger Error */
+#define PCF50606_F_CHG_PROT (1<<PCF50606_B_CHG_PROT) /* Charger Protection */
+#define PCF50606_F_CHG_READY (1<<PCF50606_B_CHG_READY) /* Charging completed */
#define PCF50606_F_CHG_MASK 0x000000fc
#define PCF50606_F_PWR_PRESSED 0x00000100
@@ -1026,12 +1033,12 @@
static DEVICE_ATTR(chgmode, S_IRUGO | S_IWUSR, show_chgmode, set_chgmode);
static const char *chgstate_names[] = {
- [PCF50606_F_CHG_FAST] = "fast_enabled",
- [PCF50606_F_CHG_PRESENT] = "present",
- [PCF50606_F_CHG_FOK] = "fast_ok",
- [PCF50606_F_CHG_ERR] = "error",
- [PCF50606_F_CHG_PROT] = "protection",
- [PCF50606_F_CHG_READY] = "ready",
+ [PCF50606_B_CHG_FAST] = "fast_enabled",
+ [PCF50606_B_CHG_PRESENT] = "present",
+ [PCF50606_B_CHG_FOK] = "fast_ok",
+ [PCF50606_B_CHG_ERR] = "error",
+ [PCF50606_B_CHG_PROT] = "protection",
+ [PCF50606_B_CHG_READY] = "ready",
};
static ssize_t show_chgstate(struct device *dev, struct device_attribute *attr,
|
|
|
|
|
|
|
|
|
|
Add Bluetooth in monolithic kernel
|
|
SD Card / VFAT in monolithic kernel
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Make a defconfig for 2.6.24 out of the current 2.6.22.5 one
From: warmcat <andy@warmcat.com>
|
|
Update to new DFU VID for A5
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Add a couple of handy scripts to crossmake and send over dfu
From: warmcat <andy@warmcat.com>
|
|
Adds svn defconfig
From: warmcat <andy@warmcat.com>
|