aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-10-07amd64_edac: fix chip select handlingBorislav Petkov
Different processor families support a different number of chip selects. Handle this in a family-dependent way with the proper values assigned at init time (see amd64_set_dct_base_and_mask). Remove _DCSM_COUNT defines since they're used at one place and originate from public documentation. CC: Keith Mannthey <kmannth@us.ibm.com> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2009-10-07amd64_edac: simple fix to allow reporting of CECC errorsKeith Mannthey
This allows the errors to be further decoded and mapped to csrows. Tested with ECC debug dimms and an Rev F cpu based system. Signed-off-by: Keith Mannthey <kmannth@us.ibm.com> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2009-10-07amd64_edac: fix K8 intlv_sel checkBorislav Petkov
The check when DRAM interleaving is enabled should be done against the pvt->dram_IntlvSel field and not against the ->dram_limit. Simplify first loop and fixup printk formatting while at it. Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2009-10-07amd64_edac: fix interleave enable testsBorislav Petkov
The pvt->dram_IntlvEn saves the 3 "Interleave Enable" bits already right-shifted by 8 so the check in find_mc_by_sys_addr() by shifting the values to the left 8 bits is wrong. Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2009-10-07amd64_edac: fix DRAM base and limit address extractionBorislav Petkov
K8 DRAM base and limit addresses from F1x40 +8*i and F1x44 + 8*i, where i in (0..7) are both bits 39-24 and therefore the shifting should be done by 24 and not by 8. Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2009-10-07amd64_edac: fix driver instance lookup table allocationBorislav Petkov
Allocate memory statically for 8-node machines max for simplicity instead of relying on MAX_NUMNODES which is 0 on !CONFIG_NUMA builds. Spotted by Jan Beulich. Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
2009-10-07ALSA: hda - Fix yet another auto-mic bug in ALC268Takashi Iwai
Since patch_alc268() doesn't call set_capture_mixer() (due to its h/w design different from other siblings), it needs to call fixup_automic_adc() explicitly to set up the auto-mic routing. Otherwise the indices for int/ext mics aren't set properly. Reference: Novell bnc#544899 http://bugzilla.novell.com/show_bug.cgi?id=544899 Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-10-07Revert "Revert "ide: try to use PIO Mode 0 during probe if possible""Bartlomiej Zolnierkiewicz
This reverts commit 24df31acaff8465d797f0006437b45ad0f2a5cb1. The root cause of reported system hangs was (now fixed) sis5513 bug and not "ide: try to use PIO Mode 0 during probe if possible" change (commit 6029336426a2b43e4bc6f4a84be8789a047d139e) so the revert was incorrect (it simply replaced one regression with the other one). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07sis5513: fix PIO setup for ATAPI devicesBartlomiej Zolnierkiewicz
Clear prefetch setting before potentially (re-)enabling it in config_drive_art_rwp() so the transition of the device type on the port from ATA to ATAPI (i.e. during warm-plug operation) is handled correctly. This is a really old bug (it probably goes back to very early days of the driver) but it was only affecting warm-plug operation until the recent "ide: try to use PIO Mode 0 during probe if possible" change (commit 6029336426a2b43e4bc6f4a84be8789a047d139e). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Tested-by: David Fries <david@fries.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07NOHZ: update idle state also when NOHZ is inactiveEero Nurkkala
Commit f2e21c9610991e95621a81407cdbab881226419b had unfortunate side effects with cpufreq governors on some systems. If the system did not switch into NOHZ mode ts->inidle is not set when tick_nohz_stop_sched_tick() is called from the idle routine. Therefor all subsequent calls from irq_exit() to tick_nohz_stop_sched_tick() fail to call tick_nohz_start_idle(). This results in bogus idle accounting information which is passed to cpufreq governors. Set the inidle flag unconditionally of the NOHZ active state to keep the idle time accounting correct in any case. [ tglx: Added comment and tweaked the changelog ] Reported-by: Steven Noonan <steven@uplinklabs.net> Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Cc: Rik van Riel <riel@redhat.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Greg KH <greg@kroah.com> Cc: Steven Noonan <steven@uplinklabs.net> Cc: stable@kernel.org LKML-Reference: <1254907901.30157.93.camel@eenurkka-desktop> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2009-10-07ethoc: limit the number of buffers to 128Thomas Chou
Only 128 buffer descriptors are supported in the core. Limit the number in case we have more memory. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: use system memory as bufferThomas Chou
This patch enabled the ethoc to allocate system memory as buffer when there is no dedicated buffer memory. Some hardware designs may not have dedicated buffer memory such as on chip or off chip SRAM. In this case, only one memory resource is supplied in the platform data instead of two. Then a DMA buffer can be allocated from system memory and used for the transfer. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: align received packet to make IP header at word boundaryThomas Chou
The packet buffer is allocated at 4 bytes boundary, but the IP header length and version bits is located at byte 14. These bit fields access as 32 bits word and caused exception on processors that do not support unaligned access. The patch adds 2 bytes offset to make the bit fields word aligned. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: fix buffer address mappingThomas Chou
The pointer address in buffer descriptors is physical address. The pointer that processor used to access packet is virtual address. Though the higher bits of pointer address used by the MAC may be truncated to zero in special case, it is not always true in larger designs. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ethoc: fix typo to compute number of tx descriptorsThomas Chou
It should be max() instead of min(). Use 1/4 of available descriptors for tx, and there should be at least 2 tx descriptors. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats()roel kluin
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT. in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07netxen: Fix Unlikely(x) > yRoel Kluin
The closing parenthesis was not on the right location. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07pasemi_mac: ethtool get settings fixValentine Barshak
Not all pasemi mac interfaces can have a phy attached. For example, XAUI has no phy and phydev is NULL for it. In this case ethtool get settings causes kernel crash. Fix it by returning -EOPNOTSUPP if there's no PHY attached. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07add maintainer for network drop monitor kernel serviceNeil Horman
I was getting ribbed about this earlier, so I figured I'd make it official. Add myself as the maintainer of the drop monitor bits, so people don't just gripe at Dave when it breaks (I'm sure it will never break, but just in case :) ). Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07tg3: Fix phylib locking strategyMatt Carlson
Felix Radensky noted that chip resets were generating stack trace dumps. This is because the driver is attempting to acquire the mdio bus mutex while holding the tp->lock spinlock. The fix is to change the code such that every phy access takes the tp->lock spinlock instead. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07rndis_host: support ETHTOOL_GPERMADDRJohn W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07ipv4: arp_notify address list bugStephen Hemminger
This fixes a bug with arp_notify. If arp_notify is enabled, kernel will crash if address is changed and no IP address is assigned. http://bugzilla.kernel.org/show_bug.cgi?id=14330 Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: add kerneldoc commentsTilman Schmidt
Add kerneldoc comments to some functions in the Gigaset driver. Impact: documentation Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: correct debugging output selectionTilman Schmidt
Dump payload data consistently only when DEBUG_STREAM_DUMP debug bit is set. Impact: debugging aid Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: improve error recoveryTilman Schmidt
When the Gigaset base stops responding, try resetting the USB connection to recover. Impact: error handling improvement Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: fix device ERROR response handlingTilman Schmidt
Clear out pending command that got rejected with 'ERROR' response. This fixes the bug where unloading the driver module would hang with the message: "gigaset: not searching scheduled commands: busy" after a device communication error. Impact: error handling bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: announce if built with debuggingTilman Schmidt
Mention in the driver load announcement whether the driver was built with debugging messages enabled, to facilitate support. Impact: informational message Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: handle isoc frame errors more gracefullyTilman Schmidt
Don't drop the remainder of an URB if an isochronous frame has an error. Impact: error handling improvement Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: linearize skbTilman Schmidt
The code of the Gigaset driver assumes that sk_buff-s coming from the ISDN4Linux subsystem are always linear. Explicitly calling skb_linearize() is cheap if they are, but much more robust in case they ever aren't. Impact: robustness improvement Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06gigaset: fix reject/hangup handlingTilman Schmidt
Signal D channel disconnect in a few cases where it was missed, including when an incoming call is disconnected before it was accepted. Impact: error handling improvement Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06isdn: make capidrv module parameter "debugmode" writeableTilman Schmidt
Being able to change the debugmode module parameter of capidrv on the fly is quite useful for debugging and doesn't do any harm. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06isdn: avoid races in capidrvTilman Schmidt
In several places, capidrv sends a CAPI message to the ISDN device and then updates its internal state accordingly. If the response message from the device arrives before the state is updated, it may be rejected or processed incorrectly. Avoid these races by updating the state before emitting the message. Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Acked-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06isdn: accept CAPI Informational Info values as successTilman Schmidt
Info values in the 0x00xx range are defined in the CAPI standard as "Informational, message processed successfully". Therefore a CONNECT_B3_CONF message with an Info value in that range should open an NCCI just as with Info==0. Impact: minor bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Acked-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06Documentation: expand isdn/INTERFACE.CAPI documentTilman Schmidt
- Note that send_message() may be called in interrupt context. - Describe the storage of CAPI messages and payload data in SKBs. - Add more details to the description of the _cmsg structure. - Describe kernelcapi debugging output. Impact: documentation Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07drm/radeon: Fix setting of bitsRoel Kluin
Duplicate bits set Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-10-06be2net: Bug fix to properly update ethtool tx-checksumming after ethtool -K ↵Ajit Khaparde
<ifname> tx off This is a fix for a bug which was a result of wrong use of checksum offload flag. The status of tx-checksumming was not changed from on to off after a 'ethtool -K <ifname> tx off' operation. Use the proper checksum offload flag NETIF_F_HW_CSUM instead of NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM. Patch is against net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06be2net: Fix a typo in be_cmds.hAjit Khaparde
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66. This patch fixes this typo. Patch against net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06be2net: Bug Fix while accounting of multicast frames during netdev stats updateAjit Khaparde
While updating the statistics to be passed via the get_stats, tx multicast frames were being accounted instead of rx multicast frames. This patch fixes the bug. This patch is against the net-2.6 tree. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix lock/mutex warnings.Ron Mercer
Get rid of spinlock and private mutex usage for exclusive access to the HW semaphore register. rtnl_lock already creates exclusive access to this register in all driver API. Add rtnl to firmware worker threads that also use the HW semaphore register. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix queueing of firmware handler in ISR.Ron Mercer
Check that we are not already polling firmware events before we queue the firmware event worker, then disable firmware interrupts. Otherwise we can queue the same event multiple times. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06qlge: Fix some bit definitions for reset register.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06Merge branch 'upstream/wm8350' into for-2.6.32Mark Brown
2009-10-06ASoC: WM8350 capture PGA mutes are invertedMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
2009-10-06ASoC: Remove absent SYNC and TDM DAI format options from i.MX SSIMark Brown
These should be handled via set_tdm_slot() now and cause build failures as-is. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-10-06Merge branch 'pm-fixes-32' of ↵Tony Lindgren
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-fixes-for-linus
2009-10-06omapfb: Blizzard: constify register address tablesTommi Rantala
Constify register address tables Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com> Cc: Imre Deak <imre.deak@nokia.com> Signed-off-by: Tommi Rantala <tt.rantala@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-06omapfb: Blizzard: fix pointer to be constTommi Rantala
Fixes a compiler warning: warning: assignment discards qualifiers from pointer target type Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com> Cc: Imre Deak <imre.deak@nokia.com> Signed-off-by: Tommi Rantala <tt.rantala@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-06omapfb: Condition mutex acquisitionSergio Aguirre
This fixes a bug introduced by this commit ID: commit 537a1bf059fa312355696fa6db80726e655e7f17 Author: Krzysztof Helt <krzysztof.h1@wp.pl> Date: Tue Jun 30 11:41:29 2009 -0700 fbdev: add mutex for fb_mmap locking In which a mutex was added when changing smem_start and smem_len fields, so the mutex inside the fb_mmap() call is actually used. The problem was that set_fb_fix, which modifies the above 2 fields, was called before and after registering the framebuffer, which when used before registration, lead to a failed attempt to use an uninitialized mutex. Solution: Don't use mutex before framebuffer registration. Signed-off-by: Sergio Aguirre <saaguirre@ti.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com> Acked-by: Imre Deak <imre.deak@nokia.com> Tested-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-06omap: iovmm: Add missing mutex_unlockDaniel Walker
I was using Coccinelle with the mutex_unlock semantic patch, and it unconvered this problem. It appears to be a valid missing unlock issue. This change should correct it by moving the unlock below the label. This patch is against the mainline kernel. Cc: Julia Lawall <julia@diku.dk> Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Daniel Walker <dwalker@fifo99.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-10-06omap: iovmm: Fix incorrect spellingHiroshi DOYU
Fix incorrect spelling Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 03:32:54 +0000