| Age | Commit message (Collapse) | Author |
|---|
|
To disable CLFLUSH usage, especially in change_page_attr().
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
On some machines, buggy BIOSes don't properly setup WB MTRRs to cover all
available RAM, meaning the last few megs (or even gigs) of memory will be
marked uncached. Since Linux tends to allocate from high memory addresses
first, this causes the machine to be unusably slow as soon as the kernel
starts really using memory (i.e. right around init time).
This patch works around the problem by scanning the MTRRs at boot and
figuring out whether the current end_pfn value (setup by early e820 code)
goes beyond the highest WB MTRR range, and if so, trimming it to match. A
fairly obnoxious KERN_WARNING is printed too, letting the user know that
not all of their memory is available due to a likely BIOS bug.
Something similar could be done on i386 if needed, but the boot ordering
would be slightly different, since the MTRR code on i386 depends on the
boot_cpu_data structure being setup.
This patch fixes a bug in the last patch that caused the code to run on
non-Intel machines (AMD machines apparently don't need it and it's untested
on other non-Intel machines, so best keep it off).
Further enhancements and fixes from:
Yinghai Lu <Yinghai.Lu@Sun.COM>
Andi Kleen <ak@suse.de>
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
For K8 system: 4G RAM with memory hole remapping enabled, or more than
4G RAM installed.
when try to use kexec second kernel, and the first doesn't include
gart_shutdown. the second kernel could have different aper position than
the first kernel. and second kernel could use that hole as RAM that is
still used by GART set by the first kernel. esp. when try to kexec
2.6.24 with sparse mem enable from previous kernel (from RHEL 5 or SLES
10). the new kernel will use aper by GART (set by first kernel) for
vmemmap. and after new kernel setting one new GART. the position will be
real RAM. the _mapcount set is lost.
Bad page state in process 'swapper'
page:ffffe2000e600020 flags:0x0000000000000000 mapping:0000000000000000 mapcount:1 count:0
Trying to fix it up, but a reboot is needed
Backtrace:
Pid: 0, comm: swapper Not tainted 2.6.24-rc7-smp-gcdf71a10-dirty #13
Call Trace:
[<ffffffff8026401f>] bad_page+0x63/0x8d
[<ffffffff80264169>] __free_pages_ok+0x7c/0x2a5
[<ffffffff80ba75d1>] free_all_bootmem_core+0xd0/0x198
[<ffffffff80ba3a42>] numa_free_all_bootmem+0x3b/0x76
[<ffffffff80ba3461>] mem_init+0x3b/0x152
[<ffffffff80b959d3>] start_kernel+0x236/0x2c2
[<ffffffff80b9511a>] _sinittext+0x11a/0x121
and
[ffffe2000e600000-ffffe2000e7fffff] PMD ->ffff81001c200000 on node 0
phys addr is : 0x1c200000
RHEL 5.1 kernel -53 said:
PCI-DMA: aperture base @ 1c000000 size 65536 KB
new kernel said:
Mapping aperture over 65536 KB of RAM @ 3c000000
So could try to disable that GART if possible.
According to Ingo
> hm, i'm wondering, instead of modifying the GART, why dont we simply
> _detect_ whatever GART settings we have inherited, and propagate that
> into our e820 maps? I.e. if there's inconsistency, then punch that out
> from the memory maps and just dont use that memory.
>
> that way it would not matter whether the GART settings came from a [old
> or crashing] Linux kernel that has not called gart_iommu_shutdown(), or
> whether it's a BIOS that has set up an aperture hole inconsistent with
> the memory map it passed. (or the memory map we _think_ i tried to pass
> us)
>
> it would also be more robust to only read and do a memory map quirk
> based on that, than actively trying to change the GART so early in the
> bootup. Later on we have to re-enable the GART _anyway_ and have to
> punch a hole for it.
>
> and as a bonus, we would have shored up our defenses against crappy
> BIOSes as well.
add e820 modification for gart inconsistent setting.
gart_fix_e820=off could be used to disable e820 fix.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The 32 bit x86 tree has a very useful feature that prints the Code: line
for the code even before the trapping instrution (and the start of the
trapping instruction is then denoted with a <>). Unfortunately, the 64 bit
x86 tree does not yet have this feature, making diagnosing backtraces harder
than needed.
This patch adds this feature in the same was as the 32 bit tree has
(including the same kernel boot parameter), and including a bugfix
to make the code use probe_kernel_address() rarther than a buggy (deadlocking)
__get_user.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
support according to fixes of x86_64 support.
- Delete efi_rt_lock because it is used during system early boot,
before SMP is initialized.
- Change local_flush_tlb() to __flush_tlb_all() to flush global page
mapping.
- Clean up includes.
- Revise Kconfig description.
- Enable noefi kernel parameter on i386.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This makes x86_64's ia32 emulation support share the sources used in the
32-bit kernel for the 32-bit vDSO and much of its setup code.
The 32-bit vDSO mapping now behaves the same on x86_64 as on native 32-bit.
The abi.syscall32 sysctl on x86_64 now takes the same values that
vm.vdso_enabled takes on the 32-bit kernel. That is, 1 means a randomized
vDSO location, 2 means the fixed old address. The CONFIG_COMPAT_VDSO
option is now available to make this the default setting, the same meaning
it has for the 32-bit kernel. (This does not affect the 64-bit vDSO.)
The argument vdso32=[012] can be used on both 32-bit and 64-bit kernels to
set this paramter at boot time. The vdso=[012] argument still does this
same thing on the 32-bit kernel.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
various changes to the in_p/out_p delay details:
- add the io_delay=none method
- make each method selectable from the kernel config
- simplify the delay code a bit by getting rid of an indirect function call
- add the /proc/sys/kernel/io_delay_type sysctl
- change 'io_delay=standard|alternate' to io_delay=0x80 and io_delay=0xed
- make the io delay config not depend on CONFIG_DEBUG_KERNEL
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: "David P. Reed" <dpreed@reed.com>
|
|
x86: provide a DMI based port 0x80 I/O delay override.
Certain (HP) laptops experience trouble from our port 0x80 I/O delay
writes. This patch provides for a DMI based switch to the "alternate
diagnostic port" 0xed (as used by some BIOSes as well) for these.
David P. Reed confirmed that port 0xed works for him and provides a
proper delay. The symptoms of _not_ working are a hanging machine,
with "hwclock" use being a direct trigger.
Earlier versions of this attempted to simply use udelay(2), with the
2 being a value tested to be a nicely conservative upper-bound with
help from many on the linux-kernel mailinglist but that approach has
two problems.
First, pre-loops_per_jiffy calibration (which is post PIT init while
some implementations of the PIT are actually one of the historically
problematic devices that need the delay) udelay() isn't particularly
well-defined. We could initialise loops_per_jiffy conservatively (and
based on CPU family so as to not unduly delay old machines) which
would sort of work, but...
Second, delaying isn't the only effect that a write to port 0x80 has.
It's also a PCI posting barrier which some devices may be explicitly
or implicitly relying on. Alan Cox did a survey and found evidence
that additionally some drivers may be racy on SMP without the bus
locking outb.
Switching to an inb() makes the timing too unpredictable and as such,
this DMI based switch should be the safest approach for now. Any more
invasive changes should get more rigid testing first. It's moreover
only very few machines with the problem and a DMI based hack seems
to fit that situation.
This also introduces a command-line parameter "io_delay" to override
the DMI based choice again:
io_delay=<standard|alternate>
where "standard" means using the standard port 0x80 and "alternate"
port 0xed.
This retains the udelay method as a config (CONFIG_UDELAY_IO_DELAY) and
command-line ("io_delay=udelay") choice for testing purposes as well.
This does not change the io_delay() in the boot code which is using
the same port 0x80 I/O delay but those do not appear to be a problem
as David P. Reed reported the problem was already gone after using the
udelay version. He moreover reported that booting with "acpi=off" also
fixed things and seeing as how ACPI isn't touched until after this DMI
based I/O port switch I believe it's safe to leave the ones in the boot
code be.
The DMI strings from David's HP Pavilion dv9000z are in there already
and we need to get/verify the DMI info from other machines with the
problem, notably the HP Pavilion dv6000z.
This patch is partly based on earlier patches from Pavel Machek and
David P. Reed.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Information about a ccw device will be dumped in
case of a ccw timeout. This can be enabled with
the kernel parameter ccw_timeout_log.
Signed-off-by: Sebastian Ott <sebott@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Sebastian Ott <sebott@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
|
|
Change the NMI handler to use the die notifier chain to signal anyone
who cares. Add a simple "nmi debugger" which hooks into this chain and
that may dump registers, task state, etc. when it happens.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
|
|
This adds the hugepagesz boot-time parameter for ppc64. It lets one
pick the size for huge pages. The choices available are 64K and 16M
when the base page size is 4k. It defaults to 16M (previously the
only only choice) if nothing or an invalid choice is specified.
Tested 64K huge pages successfully with the libhugetlbfs 1.2.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Minor corrections and additions to 'scsi_logging_level', as pointed out
by Chuck Ebbert.
Also point out the IBM S390-tools 'scsi_logging_level' script.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The console is now by default in UTF-8 mode. Fix the documentation on
the default value, so that we can explain behaviour that otherwise
causes bug-reports like this:
http://bugzilla.kernel.org/show_bug.cgi?id=9319
Also add the needed "vt." prefix, so that the boot-time config options
to switch back to the legacy 8-bit mode is actually documented
correctly.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Start in POLL mode, and if we receive confirmation GPE,
switch to INT mode.
If confirmations are not sent, switch back to POLL.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
profile=sleep only works if CONFIG_SCHEDSTATS is set. This patch notes
the limitation in Documentation/kernel-parameters.txt and prints a
warning at boot-time if profile=sleep is used without CONFIG_SCHEDSTAT.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch adds a quirk from LinuxBIOS to force enable HPET on
the nVidia CK804 (nForce 4) chipset.
This quirk can very likely support more than just nForce 4
(LinuxBIOS use the same code for nForce 5), and possibly nForce 3,
but I don't have those chipsets, so cannot add and test them.
Tested on an Abit KN9 (CK804).
Signed-off-by: Carlos Corbacho <cathectic@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Documentation/kernel-parameters.txt | 3 +-
arch/x86/kernel/quirks.c | 37 +++++++++++++++++++++++++++++++++++-
2 files changed, 38 insertions(+), 2 deletions(-)
|
|
Introduce intel_iommu=forcedac commandline option. This option is helpful to
verify the pci device capability of handling physical dma'able address greater
than 4G.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Actual intel IOMMU driver. Hardware spec can be found at:
http://www.intel.com/technology/virtualization
This driver sets X86_64 'dma_ops', so hook into standard DMA APIs. In this
way, PCI driver will get virtual DMA address. This change is transparent to
PCI drivers.
[akpm@linux-foundation.org: remove unneeded cast]
[akpm@linux-foundation.org: build fix]
[bunk@stusta.de: fix duplicate CONFIG_DMAR Makefile line]
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
|
|
Whilst looking up what profile=sleep did, I noticed that we missed
adding docs for the most recent addition to the profiler.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
* ssh://master.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-x86: (33 commits)
x86: convert cpuinfo_x86 array to a per_cpu array
x86: introduce frame_pointer() and stack_pointer()
x86 & generic: change to __builtin_prefetch()
i386: do not BUG_ON() when MSR is unknown
x86: acpi use cpu_physical_id
x86: convert cpu_llc_id to be a per cpu variable
x86: convert cpu_to_apicid to be a per cpu variable
i386: introduce "used_vectors" bitmap which can be used to reserve vectors.
x86: use raw locks during oopses
x86: honor _PAGE_PSE bit on page walks
i386: do cpuid_device_create() in CPU_UP_PREPARE instead of CPU_ONLINE.
x86: implement missing x86_64 function smp_call_function_mask()
x86: use descriptor's functions instead of inline assembly
i386: consolidate show_regs and show_registers for i386
i386: make callgraph use dump_trace() on i386/x86_64
x86: enable iommu_merge by default
i386: i386 add AMD64 Barcelona PMU MSR definitions to msr.h
x86: Unify i386 and x86-64 early quirks
x86: enable HPET on ICH3 and ICH4
x86: force enable HPET on VT8235/8237 chipsets
...
Manually fix trivial conflict with task pid container helper changes in
arch/x86/kernel/process_32.c
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
given the following:
$ grep -rw sg_def_reserved_size *
Documentation/kernel-parameters.txt: sg_def_reserved_size= [SCSI]
$
that kernel parameter looks exceedingly dead.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
>From commit cd8c93a4e04dce8f00d1ef3a476aac8bd65ae40b:
"Similar functionality was turned on by acpi_fake_ecdt=1 command line
before. Now it is on all the time."
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Since the OSS-related "sb" kernel parameter doesn't seem to be
supported, drop its reference from the kernel-parameters.txt file.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Armin Schindler <armin@melware.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
This adds the documentation for the extended crashkernel syntax into
Documentation/kdump/kdump.txt.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
add force_hpet boot option.
(this will be useful to make the forced-enable quirks depend on.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Currently, there's a CONFIG_DISABLE_CONSOLE_SUSPEND that allows one to stop
the serial console from being suspended when the rest of the machine goes
to sleep. This is incredibly useful for debugging power management-related
things; however, having it as a compile-time option has proved to be
incredibly inconvenient for us (OLPC). There are plenty of times that we
want serial console to not suspend, but for the most part we'd like serial
console to be suspended.
This drops CONFIG_DISABLE_CONSOLE_SUSPEND, and replaces it with a kernel
boot parameter (no_console_suspend). By default, the serial console will
be suspended along with the rest of the system; by passing
'no_console_suspend' to the kernel during boot, serial console will remain
alive during suspend.
For now, this is pretty serial console specific; further fixes could be
applied to make this work for things like netconsole.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the = into the __setup line.
Document the option in kernel-parameters.txt by adding a pointer
to the x86-64 specific documentation.
[ tglx: arch/x86 adaptation ]
Pointed out by Robert Day
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Convert LSM into a static interface, as the ability to unload a security
module is not required by in-tree users and potentially complicates the
overall security architecture.
Needlessly exported LSM symbols have been unexported, to help reduce API
abuse.
Parameters for the capability and root_plug modules are now specified
at boot.
The SECURITY_FRAMEWORK_VERSION macro has also been removed.
In a nutshell, there is no safe way to unload an LSM. The modular interface
is thus unecessary and broken infrastructure. It is used only by out-of-tree
modules, which are often binary-only, illegal, abusive of the API and
dangerous, e.g. silently re-vectoring SELinux.
[akpm@linux-foundation.org: cleanups]
[akpm@linux-foundation.org: USB Kconfig fix]
[randy.dunlap@oracle.com: fix LSM kernel-doc]
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Acked-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since the "ramdisk" kernel parameter has been officially deprecated
since at least 2.6.18, might as well finally get rid of it.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add logo.nologo kernel boot option to disable the logo in order to provide
more screen space for kernel messages; especially useful when debugging and
screen space is more critical.
newport_con driver changes are untested.
[akpm@linux-foundation.org: cleanups, coding-style fixes]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Optionally add a boot delay after each kernel printk() call, crudely
measured in milliseconds, with a maximum delay of 10 seconds per printk.
Enable CONFIG_BOOT_PRINTK_DELAY=y and then add (e.g.):
"lpj=loops_per_jiffy boot_delay=100"
to the kernel command line.
It has been useful in cases like "during boot, my machine just reboots or the
screen goes black" by slowing down printk, (and adding initcall_debug), we can
usually see the last thing that happened before the lights went out which is
usually a valuable clue.
[akpm@linux-foundation.org: not all architectures implement CONFIG_HZ]
[akpm@linux-foundation.org: fix lots of stuff]
[bunk@stusta.de: kernel/printk.c: make 2 variables static]
[heiko.carstens@de.ibm.com: fix slow down printk on boot compile error]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: use full RCU API
Input: remove tsdev interface
Input: add support for Blackfin BF54x Keypad controller
Input: appletouch - another fix for idle reset logic
HWMON: hdaps - switch to using input-polldev
Input: add support for SEGA Dreamcast keyboard
Input: omap-keyboard - don't pretend we support changing keymap
Input: lifebook - fix X and Y axis range
Input: usbtouchscreen - add support for GeneralTouch devices
Input: fix open count handling in input interfaces
Input: keyboard - add CapsShift lock
Input: adbhid - produce all CapsLock key events
Input: ALPS - add signature for ThinkPad R61
Input: jornada720_kbd - send MSC_SCAN events
Input: add support for the HP Jornada 7xx (710/720/728) touchscreen
Input: add support for HP Jornada 7xx onboard keyboard
Input: add support for HP Jornada onboard keyboard (HP6XX)
Input: ucb1400_ts - use schedule_timeout_uninterruptible
Input: xpad - fix dependancy on LEDS class
Input: auto-select INPUT for MAC_EMUMOUSEBTN option
...
Resolved conflicts manually in drivers/hwmon/applesmc.c: converting from
a class device to a device and converting to use input-polldev created a
few apparently trivial clashes..
|
|
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (131 commits)
NFSv4: Fix a typo in nfs_inode_reclaim_delegation
NFS: Add a boot parameter to disable 64 bit inode numbers
NFS: nfs_refresh_inode should clear cache_validity flags on success
NFS: Fix a connectathon regression in NFSv3 and NFSv4
NFS: Use nfs_refresh_inode() in ops that aren't expected to change the inode
SUNRPC: Don't call xprt_release in call refresh
SUNRPC: Don't call xprt_release() if call_allocate fails
SUNRPC: Fix buggy UDP transmission
[23/37] Clean up duplicate includes in
[2.6 patch] net/sunrpc/rpcb_clnt.c: make struct rpcb_program static
SUNRPC: Use correct type in buffer length calculations
SUNRPC: Fix default hostname created in rpc_create()
nfs: add server port to rpc_pipe info file
NFS: Get rid of some obsolete macros
NFS: Simplify filehandle revalidation
NFS: Ensure that nfs_link() returns a hashed dentry
NFS: Be strict about dentry revalidation when doing exclusive create
NFS: Don't zap the readdir caches upon error
NFS: Remove the redundant nfs_reval_fsid()
NFSv3: Always use directory post-op attributes in nfs3_proc_lookup
...
Fix up trivial conflict due to sock_owned_by_user() cleanup manually in
net/sunrpc/xprtsock.c
|
|
Remove the obsolete tsdev.c driver as scheduled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (119 commits)
[libata] struct pci_dev related cleanups
libata: use ata_exec_internal() for PMP register access
libata: implement ATA_PFLAG_RESETTING
libata: add @timeout to ata_exec_internal[_sg]()
ahci: fix notification handling
ahci: clean up PORT_IRQ_BAD_PMP enabling
ahci: kill leftover from enabling NCQ over PMP
libata: wrap schedule_timeout_uninterruptible() in loop
libata: skip suppress reporting if ATA_EHI_QUIET
libata: clear ehi description after initial host report
pata_jmicron: match vendor and class code only
libata: add ST9160821AS / 3.ALD to NCQ blacklist
pata_acpi: ACPI driver support
libata-core: Expose gtm methods for driver use
libata: add HDT722516DLA380 to NCQ blacklist
libata: blacklist NCQ on Seagate Barracuda ST380817AS
[libata] Turn on ACPI by default
libata_scsi: Fix ATAPI transfer lengths
libata: correct handling of SRST reset sequences
libata: Integrate ACPI-based PATA/SATA hotplug - version 5
...
|
