| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds the code required to register the F75375 device on the
GLAN Tank.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch is required, in conjunction with the patch submitted to
linux-mtd [1], to access the flash memory device in the GLAN Tank.
Without the patches, the boot log shows
physmap platform flash device: 00080000 at f0000000
...
physmap-flash physmap-flash.0: map_probe failed
whereas with the patches, the boot log shows
physmap platform flash device: 00080000 at f0000000
Found: ST M29W400DB
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
...
cmdlinepart partition parsing not available
Searching for RedBoot partition table in physmap-flash.0 at offset 0x70000
No RedBoot partition table detected in physmap-flash.0
The change made by this patch is required because the ST M29W400DB
flash memory chip in the GLAN Tank is used in 16 bit bus mode (~BYTE
pin is high when the board is powered on).
[1] http://lists.infradead.org/pipermail/linux-mtd/2008-January/020291.html
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use the new i2c framework to load rtc-rs5c372 for the GLAN Tank.
Tested-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Adds the platform device definitions and the architecture specific support
routines (i.e. register initialization and descriptor formats) for the
iop-adma driver.
Changelog:
* add support for > 1k zero sum buffer sizes
* added dma/aau platform devices to iq80321 and iq80332 setup
* fixed the calculation in iop_desc_is_aligned
* support xor buffer sizes larger than 16MB
* fix places where software descriptors are assumed to be contiguous, only
hardware descriptors are contiguous for up to a PAGE_SIZE buffer size
* convert to async_tx
* add interrupt support
* add platform devices for 80219 boards
* do not call platform register macros in driver code
* remove switch() statements for compatible register offsets/layouts
* change over to bitmap based capabilities
* remove unnecessary ARM assembly statement
* checkpatch.pl fixes
* gpl v2 only correction
* phys move to dma_async_tx_descriptor
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
WARNING: arch/arm/mach-iop13xx/built-in.o - Section mismatch: reference to
.init.text:iop13xx_pcie_map_irq from .text between 'iop13xx_pci_setup' (at
offset 0x7fc) and 'iop13xx_map_pci_memory'
While fixing this warning I also recalled Adrian Bunk's recommendation to
not use inline in .c files, as 'iop13xx_map_pci_memory' is needlessly
inlined.
Removing 'inline' uncovered some dead code so that is cleaned up as well.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* architecture specific details are handled in asm/arch/time.h
* ARCH_IOP13XX now selects PLAT_IOP
* as suggested by Lennert use ifdef CONFIG_XSCALE to skip the cp_wait on
XSC3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for the IO-Data GLAN Tank, from Martin Michlmayr.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
