| Age | Commit message (Collapse) | Author |
|---|
|
The GPIO interrupts can be configured as either level triggered or edge
triggered, with a default of level triggered. When an edge triggered
interrupt is requested, the gpio_irq_set_type method is called which
currently switches the given IRQ descriptor between two struct irq_chip
instances: orion_gpio_irq_level_chip and orion_gpio_irq_edge_chip. This
happens via __setup_irq() which also calls irq_chip_set_defaults() to
assign default methods to uninitialized ones. The problem is that
irq_chip_set_defaults() is called before the irq_chip reference is
switched, leaving the new irq_chip (orion_gpio_irq_edge_chip in this
case) with uninitialized methods such as chip->startup() causing a kernel
oops.
Many solutions are possible, such as making irq_chip_set_defaults() global
and calling it from gpio_irq_set_type(), or calling __irq_set_trigger()
before irq_chip_set_defaults() in __setup_irq(). But those require
modifications to the generic IRQ code which might have adverse effect on
other architectures, and that would still be a fragile arrangement.
Manually copying the missing methods from within gpio_irq_set_type()
would be really ugly and it would break again the day new methods with
automatic defaults are added.
A better solution is to have a single irq_chip instance which can deal
with both edge and level triggered interrupts. It is also a good idea
to switch the IRQ handler instead, as the edge IRQ handler allows for
one edge IRQ event to be queued as the IRQ is actually masked only when
that second IRQ is received, at which point the hardware can queue an
additional IRQ event, making edge triggered interrupts a bit more
reliable.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Otherwise the mv643xx_eth driver will assume 133 MHz which is incorrect.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit ba84be2338d3 broke the build.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
|
|
On newer versions of the RD88F6281 board, the WAN port is connected to
its own ethernet port on the CPU, via a separate PHY, whereas on older
versions of the board, it is connected to one of the PHYs in the
ethernet switch. In the RD8F6281 setup code, detect which version of
the board we are running on, and instantiate the ethernet ports and
switch driver accordingly.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The 88f6192 and 88f6281 Kirkwood SoCs support two ethernet ports.
Add the platform glue that will allow board support files to
instantiate the second ethernet port.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The Orion ehci driver serves the Orion, kirkwood and DD Soc families.
Since each of those integrate a different USB phy we should have the
ability to use few initialization sequences or to leave the boot loader
phy settings as is.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
|
|
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds DSA switch instantiation hooks to the orion5x and the
kirkwood ARM SoC platform code, and instantiates the DSA switch
driver on the 88F5181L FXO RD, the 88F5181L GE RD, the 6183 AP GE
RD, the Linksys WRT350n v2, and the 88F6281 RD boards.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
|
|
Feroceon L2 cache can work in eighther write through or write back mode
on Kirkwood. Add the option to configure this mode according to Kconfig.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Remove uart1 init calls for boards that use the physical pins onto
which the UART1 signals are multiplexed for different purposes.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Add support to the Kirkwood port for newer device models and silicon
revisions. Instead of looking at the DEVICE_ID register, the device
version is now determined by looking at the PCI-Express device ID and
revision registers, as it is done for orion5x, and this information
is used to determine the TCLK frequency, again, as it is done for
orion5x.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Currently, kirkwood uses a hardcoded timer tick rate of 166 MHz, but
the actual timer tick rate varies between different members of the SoC
family.
This patch prepares for runtime determination of the timer tick rate.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
|
|
Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Currently, there are two different fields in the
mv643xx_eth_platform_data struct that together describe the PHY
address -- one field (phy_addr) has the address of the PHY, but if
that address is zero, a second field (force_phy_addr) needs to be
set to distinguish the actual address zero from a zero due to not
having filled in the PHY address explicitly (which should mean
'use the default PHY address').
If we are a bit smarter about the encoding of the phy_addr field,
we can avoid the need for a second field -- this patch does that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The mv643xx_eth hardware has a provision for polling the PHY's
MII management registers to obtain the (R)(G)MII interface speed
(10/100/1000) and duplex (half/full) and pause (off/symmetric)
settings to use to talk to the PHY.
The driver currently does not make use of this feature. Instead,
whenever there is a link status change event, it reads the current
link parameters from the PHY, and programs those parameters into
the mv643xx_eth MAC by hand.
This patch switches the mv643xx_eth driver to letting the MAC
auto-determine the (R)(G)MII link parameters by PHY polling, if there
is a PHY present. For PHYless ports (when e.g. the (R)(G)MII
interface is connected to a hardware switch), we keep hardcoding the
MII interface parameters.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
This patch allows booting Kirkwood with the L2 in writeback mode,
by reading the WT override bit from the L2 config register and
passing that into the Feroceon L2 init routine, instead of assuming
that the WT override bit will always be set
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
|
The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.
This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
|
