| Age | Commit message (Collapse) | Author |
|---|
|
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
devel
|
|
Add basic support for MX35PDK board (www.freescale.com/imx35pdk).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Kconfig entries default to n, so there's no need for this to be
explicitly specified.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based
modules. The module needs a baseboard support to work which will be
added in the next patch.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This hw-random driver add support to RNGA hardware found
on some i.MX processors.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The PCM043 is a i.MX35 based board from Phytec also known as the
phyCORE-i.MX35.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This iomux is called iomux-v3 in the tree because it is the third known
incarnation of MXC iomuxers. It is not only found on the MX35 but also
on the MX51 and probably others.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Otherwise we'd need massive ifdefs in the code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch adds basic support for Dave/DENX QongEVB-LITE i.MX31-based
board. It includes support for clocks initialization, UART1, NOR-flash,
FPGA-attached NAND flash and DNET ethernet controller (inside FPGA).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The i.MX31ADS supports pluggable PMU modules, including the WM835x based
Wolfson Microelectronics 1133-EV1. These boards provide power, audio,
RTC and watchdiog services to the system. This patch adds initial support
for those boards in I2C mode.
Currently support is limited by the available support for the features
of the i.MX31 in the mainline kernel. Some further work will be needed
once other PMU modules are supported and once there is SPI support.
Many of the regulator constraints will be sharable with other PMU
boards.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Initial support for mx31moboard platfor with 3 serial ports
and NOR Flash
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Add basic support to the MX31PDK development board, also known
as MX31 3DS or MX31 3-stack board (http://www.freescale.com/imx31pdk).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: sascha Hauer <s.hauer@pengutronix.de>
|
|
This patch adds basic support for i.MX31 LiteKit by LogicPD.
With printascii() in kernel/printk.c, it boots right into the
rootfs-panic.
Note: This is a modified version of Daniel's patch to fit into this patch
stack.
> On 09.06.2008, at 17:26, Russell King - ARM Linux wrote:
>
> > I would much prefer it if board specific includes were included by the
> > code which needs them rather than in asm/arch/hardware.h. With the
> > device model, drivers shouldn't need to include any board specific
> > includes - only the board specific C file should need it.
>
> The new version of this patch (#5102) has been uploaded to the patch
> tracker this morning.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
--
arch/arm/configs/mx31litekit_defconfig | 1100 ++++++++++++++++++++++++++++++
arch/arm/mach-mx3/Kconfig | 7
arch/arm/mach-mx3/Makefile | 1
arch/arm/mach-mx3/mx31lite.c | 96 ++
include/asm-arm/arch-mxc/board-mx31lite.h | 38 +
include/asm-arm/arch-mxc/debug-macro.S | 3
6 files changed, 1245 insertions(+)
|
|
This patch adds basic board support for phytecs pmc037 board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
