| Age | Commit message (Collapse) | Author |
|---|
|
It's worked fine so far since reset is done for the first time.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Earlier BeagleBoards were using pad AH8 muxed to GPIO29 for MMC write-protect.
However, this signal has been changed to pad AG9 in board revision C2.
Fix this by adding mux configuration for pad AG9, runtime check for board
revisions and set the gpio number and pad muxing accordingly.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise we'll get compile errors like:
arch/arm/plat-omap/include/mach/keypad.h:38:1: warning: "KEY" redefined
arch/arm/plat-omap/include/mach/keypad.h:39:1: warning: "PERSISTENT_KEY" redefined
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The only way to flush posted write to L4 bus is to do a read back
of the same register right after the write.
This seems to be mostly needed in interrupt handlers to avoid
causing spurious interrupts.
The earlier fix has been to mark the L4 bus as strongly ordered
memory, which solves the problem, but causes performance penalties.
Similar to the fix, 03803a71041e3bc3c077f4e7b92f6ceaa9426df3
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The softreset at startup is introduced as TRM describes and also some
register bit definitions are added instead of magic number.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPIO135 is used as EHCI (port2) phy reset pin on Multi Media Daughter card
connected to OMAP3EVM.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like these patches were not tested that well..
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 7869c0b9ed44404bbc675ef76f8ccb3be5496f39 added support for
additional McSPI ports. Unfortunately that broke compile for 2420.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Patch 941132606c7611246d2034cb7b01f9270c2d1ede split IO_ADDRESS
into OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS except for the omap4
code to avoid merge conflicts with the omap4 code that was queued
earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
|
|
tAdd adds McSPI support for OMAP4430 SDP platform. All the base addresses
are changed between OMAP1/2/3 and OMAP4. The fields of the resource
structures are filled at runtime to have McSPI support on OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add basic support for all 5 MMC controllers on OMAP4.
This patch doesn't include mmc-regulator support
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Specify MMC capabilities and set the power-saving flag for RX51.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the ability for the driver to put the card power regulators to sleep
and wake them up again.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Support for multi-level dynamic power saving states in omap_hsmmc
(ENABLED->DISABLED->OFF). In the "deepest" state (OFF) we switch off the
voltage regulators.
Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let the board specify that a card is nonremovable e.g. eMMC
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PM dynamic OFF state results in context loss. That is, the host
controller has been powered off at some point, which means the registers
have been reset. The driver must detect when this happens, and restore
the context. This patch adds the means to detect context loss.
Note, the PM side is not yet implemented.
Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/mtd/mtdcore.c
Merged in order that I can apply the Nomadik nand/onenand support patches.
|
|
This patch adds prefetch support to access nand flash in mpu mode.
This patch also adds 8-bit nand support (omap_read/write_buf8).
Prefetch can be used for both 8- and 16-bit devices.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Remove the ARM dependency from the generic "onenand" platform device
driver. This change makes the driver useful for other architectures as
well. Needed for the SuperH kfr2r09 board.
Apart from the obvious Kconfig bits, the most important change is the move
away from ARM specific includes and platform data. Together with this
change the only in-tree board code gets an update, and the driver name is
also changed gracefully break potential out of tree drivers.
The driver is also updated to allow NULL as platform data together with a
few changes to make use of resource_size() and dev_name().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (55 commits)
regulator: Voltage count for AB3100
mfd: Convert WM8350 to use request_threaded_irq()
mfd: Update MAINTAINERS patterns for WM831x
mfd: Fix twl4030-power warnings
regulator: AB3100 support
rtc: AB3100 RTC support
mfd: Fix ab3100-otp build failure
mfd: OMAP: Board-specifc twl4030 DPS scripts for RX51 board
mfd: Print warning for twl4030 out-of-order script loading
mfd: Add support for TWL4030/5030 dynamic power switching
mfd: AB3100 OTP readout
regulator: Add Freescale MC13783 driver
mfd: Add Freescale MC13783 driver
mfd: AB3100 disable irq nosync
mfd: AB3100 alter default setting
mfd: AB3100 propagate error
mfd: AB3100 accessor function cleanups
rtc: Add support for RTCs on Wolfson WM831x devices
regulator: get pcap data from the parent device
input: PCAP2 misc input driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (47 commits)
OMAP clock: use debugfs_remove_recursive() for rewinding
OMAP2/3/4 core: create omap_device layer
OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects
OMAP2/3/4: create omap_hwmod layer
OMAP2/3 board-*.c files: read bootloader configuration earlier
OMAP2/3/4 PRCM: add module IDLEST wait code
OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer
OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm
OMAP clock: associate MPU clocks with the mpu_clkdm
OMAP3 clock: Fixed processing of bootarg 'mpurate'
OMAP: SDRC: Add several new register definitions
OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups.
OMAP: PM: Added suspend target state control to debugfs for OMAP3
OMAP: PM debug: Add PRCM register dump support
OMAP: PM debug: make powerdomains use PM-debug counters
OMAP: PM: Add pm-debug counters
OMAP: PM: Add closures to clkdm_for_each and pwrdm_for_each.
OMAP: PM: Hook into PM counters
OMAP: PM counter infrastructure.
OMAP3: PM: fix lockdep warning caused by omap3_pm_init
...
|
|
Add support for Dynamic Power Switching (DPS) for the RX51 board.
These scripts are still a work-in-progress. I'll keep sending patches to
update the scripts as they are optimised.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
|
|
|
|
Conflicts:
MAINTAINERS
arch/arm/mm/fault.c
|
|
* topic/asoc: (226 commits)
ASoC: au1x: PSC-AC97 bugfixes
ASoC: Fix WM835x Out4 capture enumeration
ASoC: Remove unuused hw_read_t
ASoC: fix pxa2xx-ac97.c breakage
ASoC: Fully specify DC servo bits to update in wm_hubs
ASoC: Debugged improper setting of PLL fields in WM8580 driver
ASoC: new board driver to connect bfin-5xx with ad1836 codec
ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI
ASoC: davinci: i2c device creation moved into board files
ASoC: Don't reconfigure WM8350 FLL if not needed
ASoC: Fix s3c-i2s-v2 build
ASoC: Make platform data optional for TLV320AIC3x
ASoC: Add S3C24xx dependencies for Simtec machines
ASoC: SDP3430: Fix TWL GPIO6 pin mux request
ASoC: S3C platform: Fix s3c2410_dma_started() called at improper time
ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop
ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI
OMAP: McBSP: Use textual values in DMA operating mode sysfs files
ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510
ASoC: Select core DMA when building for S3C64xx
...
|
|
|
|
Connect the omap_hwmod code to the kernel boot. Create some basic
interconnect and device structures for OMAP2/3 chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
OMAP SoCs can be considered a collection of hardware IP blocks
connected by various interconnects. The bus topology and device
integration data is somewhat more complex than platform_device can
encode. This patch creates code and structures to manage information
about OMAP on-chip devices ("hardware modules") and their integration
to the rest of the chip. Hardware module data is intended to be
generated dynamically from the TI hardware database for the OMAP4
chips and beyond, easing Linux support for new chip variants.
This code currently:
- resets and configures all hardware modules upon startup, reducing bootloader
dependencies;
- provides hooks for Linux driver model code to enable, idle, and shutdown
hardware modules (forthcoming patch);
- waits for hardware modules to leave idle once their clocks
are enabled and OCP_SYSCONFIG bits are set appropriately.
- provides a means to pass arbitrary IP block configuration data (e.g.,
FIFO size) to the device driver (via the dev_attr void pointer)
In the future this code is intended to:
- estimate interconnect bandwidth and latency characteristics to
ensure constraints are satisfied during DVFS
- provide *GRPSEL bit data to the powerdomain code
- handle pin/ball muxing for devices
- generate IO mapping information dynamically
- supply device firewall configuration data
- provide hardware module data to other on-chip coprocessor software
- allow the removal of the "disable unused clocks" code in the OMAP2/3
clock code
This patch represents a collaborative effort involving many people from TI,
Nokia, and the Linux-OMAP community.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
|
|
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
After a hardware module's clocks are enabled, Linux must wait for it
to indicate readiness via its IDLEST bit before attempting to access
the device, otherwise register accesses to the device may trigger an
abort. This has traditionally been implemented in the clock
framework, but this is the wrong place for it: the clock framework
doesn't know which module clocks must be enabled for a module to leave
idle; and if a module is not in smart-idle mode, it may never leave
idle at all. This type of information is best stored in a
per-hardware module data structure (coming in a following patch),
rather than a per-clock data structure. The new code will use these new
functions to handle waiting for modules to enable.
Once hardware module data is filled in for all of the on-chip devices,
the clock framework code to handle IDLEST waiting can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The interface provides device drivers, CPUFreq, and DSPBridge with a
means of controlling OMAP power management parameters that are not yet
supported by the Linux PM PMQoS interface. Copious documentation is
in the patch in Documentation/arm/OMAP/omap_pm and the interface
header file, arch/arm/plat-omap/include/mach/omap-pm.h.
Thanks to Rajendra Nayak <rnayak@ti.com> for adding CORE (VDD2) OPP
support and moving the OPP table initialization earlier in the event
that the clock code needs them. Thanks to Tero Kristo
<tero.kristo@nokia.com> for fixing the parameter check in
omap_pm_set_min_bus_tput(). Jouni signed off on Tero's patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Stoppa <igor.stoppa@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Veeramanikandan Raju <veera@ti.com>
Cc: Karthik Dasu <karthik-dp@ti.com>
|
|
omap2_init_clk_clkdm() is called as part of the chip architecture-specific
initialization code, so calling it again from the struct clk init pointer
just wastes cycles.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
All MPU-related clocks should be in the mpu_clkdm. This is needed for the
upcoming omap_hwmod patches, which needs to know the clockdomain that arm_fck
is in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The argument 'mpurate' had no effect on the MPU
frequency. This patch fixes the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
At the end of the list pd is a pointer to a NULL struct, so checking
if the address == NULL doesn't help here. In fact the original code
will just keep running past the struct to read who knows what in
memory.
This case manifests itself when from clkdms_setup() when enabling auto
idle for a clock domain and the clockdomain usecount is greater than
0. When _clkdm_add_autodeps() tries to add the a dependency that does
not exist in the powerdomain->wkdep_srcs array the for loop will run
past the wkdep_srcs array.
Currently in linux-omap you won't hit this because the not found case
is never executed, unless you start modifying powerdomains and their
wakeup/sleep deps.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into for-next
|
|
Target state can be read / programmed via files under:
[debugfs]/pm_debug/[pwrdm]/suspend
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Allows dumping out current register contents from the debug filesystem, and
also allows user to add arbitrary register save points into code. Current
register contents are available under debugfs at:
[debugfs]/pm_debug/registers/current
To add a save point, do following:
From module init (or somewhere before the save call, called only once):
pm_dbg_init_regset(n); // n=1..4, allocates memory for dump area #n
From arbitrary code location:
pm_dbg_regset_save(n); // n=1..4, saves registers to dump area #n
After this, the register dump can be seen under [debugfs]/pm_debug/registers/n
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Make the powerdomain code call the new hook for updating the time.
Also implement the updated pwrdm_for_each.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch provides the debugfs entries and a function which will be
called by the PM code to register the time spent per domain per
state. Also some new fields are added to the powerdomain struct to
keep the time information.
NOTE: As of v2.6.29, using getnstimeofday() after drivers are
suspended is no longer safe since the timekeeping subsystem is also
suspended as part of the suspend process. Instead use sched_clock()
which on OMAP returns the 32k SYNC timer in nanoseconds.
Also, do not print out status for meta powerdomains (dpll*)
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Add some infrastructure to easily iterate over clock and power
domains.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch modifies the clock, clockdomain and OMAP3 specific
powerdomain code to call the PM counter infrastructure whenever one or
more powerdomains might have changed state.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch provides the infrastructure to count how many times a
powerdomain entered a given power state (on, inactive, retention,
off). A number of functions are provided which will be called by the
chip specific powerdomain and clockdomain code whenever a transition
might have happened.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch uses kmalloc(size,GFP_ATOMIC) instead of kmalloc(size,GFP_KERNEL)
to allocate memory for instance of struct power_state in pwrdms_setup(),
since it may be called by pwrdm_for_each() with irq disabled.
It is a easy fix for the following lockdep warning caused by
kmalloc(size,GFP_KERNEL) in pwrdms_setup():
Power Management for TI OMAP3.
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2282 lockdep_trace_alloc+0xe8/0xfc()
Modules linked in:
[<c0032ccc>] (unwind_backtrace+0x0/0xec) from [<c0056934>] (warn_slowpath_common+0x48/0x60)
[<c0056934>] (warn_slowpath_common+0x48/0x60) from [<c007da10>] (lockdep_trace_alloc+0xe8/0xfc)
[<c007da10>] (lockdep_trace_alloc+0xe8/0xfc) from [<c00cd9bc>] (kmem_cache_alloc+0x28/0x178)
[<c00cd9bc>] (kmem_cache_alloc+0x28/0x178) from [<c000f184>] (pwrdms_setup+0x30/0xf8)
[<c000f184>] (pwrdms_setup+0x30/0xf8) from [<c00381c4>] (pwrdm_for_each+0x64/0x84)
[<c00381c4>] (pwrdm_for_each+0x64/0x84) from [<c000ef60>] (omap3_pm_init+0x3f4/0x5ac)
[<c000ef60>] (omap3_pm_init+0x3f4/0x5ac) from [<c002c2c0>] (do_one_initcall+0x30/0x1d4)
[<c002c2c0>] (do_one_initcall+0x30/0x1d4) from [<c00088d8>] (kernel_init+0xa4/0x118)
[<c00088d8>] (kernel_init+0xa4/0x118) from [<c002ddf8>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1e06f8d97dc5a19b ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Release the Dbg board detection gpio once its purpose is served
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch changes for setting the padconf value for sys_nirq line
which is connected to T2 INTR1. This will fix the T2 keypad wakeup
issue on OMAP3 SDP.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
In usb_musb_pm_init, we attempt to access an MUSB register
when the i-clock may not be on, or the module is otherwise
not accessible.
We need to either:
- enable the clock before this access, or
- remove this code and move it to the bootloader, or
- enable the clock in the bootloader
If we enable the clock in the bootloader, we might as well
add the workaround in the bootloader itself. This code will
anyway be changed once hwmod is in place, so remove it for now
This allows us to boot the kernel on certain OMAP3 boards with
a bootloader that doesn't enable this clock. Without this, we
will need to upgrade the bootloaders on these boards.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Now that on-chip UARTs each have separate platform_data, the external
UART needs an non-conflicting ID. Since there are 3 on-chip UARTs,
the Zoom2 external UART will be registered after as the fourth.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
