| Age | Commit message (Collapse) | Author |
|---|
|
This is unnecessary since it is already protected by
spin_lock_irq{save, restore} in clock.c.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
According to PXA300/310 and PXA320 Developer manuals,
the ASCR[RDH] "bit needs to be cleared as part of the software
initialization coming out of any reset and coming out of D3".
The latter requirement is addressed by commit
"c4d1fb627ff3072", as for the former (coming out of any reset),
the kernel relies on boot loaders and assumes that RDH bit
is cleared there. Though, not all bootloaders follow the rule
so we have to clear the bit in kernel.
We clear the RDH bit in pxa3xx_init() function since
it is always invoked after any reset. We also preserve D1S, D2S
and D3S bits from being cleared in case we invoke pxa3xx_init()
function not from normal hardware reset (e.g. kexec scenario),
so these bits can be properly referenced later.
Signed-off-by: Dmitry Krivoschekov <dmitry.krivoschekov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
1. clear RDH bit after resuming back from D3, otherwise, the multi function
pins will retain the low power state
2. save/restore essential system registers
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* pxa-plat: (53 commits)
[ARM] 4762/1: Basic support for Toradex Colibri module
[ARM] pxa: fix mci_init functions returning -1
[ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
[ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270
[ARM] 4746/1: pcm027: network support for phyCORE-PXA270
[ARM] 4745/1: pcm027: default configuration
[ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module
[NET] smc91x: Make smc91x use IRQ resource trigger flags
[ARM] pxa: add default config for littleton
[ARM] pxa: add basic support for Littleton (PXA3xx Form Factor Platform)
[ARM] 4664/1: Add basic support for HTC Magician PDA phones
[ARM] 4649/1: Base support for pxa-based Toshiba e-series PDAs.
[ARM] pxa: skip registers saving/restoring if entering standby mode
[ARM] pxa: fix PXA27x resume
[ARM] pxa: Avoid fiddling with CKEN register on suspend
[ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme
[ARM] pxa: Add zylonite MFP wakeup configurations
[ARM] pxa: program MFPs for low power mode when suspending
[ARM] pxa: make MFP configuration processor independent
[ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functions
...
Conflicts:
arch/arm/mach-pxa/ssp.c
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The original code incorrectly returns Hz instead of KHz.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Wakeup sources on PXA3 are enabled at two levels. First, the MFP
configuration has to be set to enable which edges a specific pin
will trigger a wakeup. The pin also has to be routed to a functional
unit. Lastly, the functional unit must be enabled as a wakeup source
in the appropriate AD*ER registers (AD2D0ER for standby resume.)
This doesn't fit well with the IRQ wake scheme - we currently do a
best effort conversion from IRQ numbers to functional unit wake enable
bits. For instance, there's several USB client related enable bits but
there's no corresponding IRQs to determine which you'd want. Conversely,
there's a single enable bit covering several functional units.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch is to add the third mmc controller support _only_
for pxa310.
On zylonite, the third controller support one slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch is to add the second mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the second controller has no slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Only register the MMC, framebuffer, I2C and FICP devices when the
platform supplies the necessary platform data structures for the
devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
PXA3xx uses its own clk_pxa3xx_cken_ops, modify the code to use the
PXA3xx specific macros to define its clocks
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
