aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/plat-mxc
AgeCommit message (Collapse)Author
2009-03-13MX31 clkdev supportSascha Hauer
This patch adds clkdev support for i.MX31. This is done in a similar way done previously for i.MX27 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MX35: add clock supportSascha Hauer
This patch adds clock support for i.MX35 SoCs. We do not support setting of clock rates yet, but most interesting clock rates should be reported. I couldn't test all clock rates and the datasheet contains some obvious bugs, so expect some bugs in this code. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MXC: add cpu_is_ macrosSascha Hauer
We had hardcoded cpu_is_ macros for mxc architectures till now. As we want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_ macros which expand to 0 or 1 if only one architecture is compiled in and only check for the cpu type if more than one architecture is compiled in. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MX35: Add register definitions for the i.MX35Sascha Hauer
This patch moves the stuff common to i.MX31 and i.MX35 to mx3x.h and the specifics to mx31.h/mx35.h. We can build a kernel which runs on i.MX31 and i.MX35, so always include mx31.h and mx35.h Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13mx31moboard: initial support for various baseboardsValentin Longchamp
This enables our mx31moboard to be used on the different baseboards that we are developping according to the application needs. There are not many differences between the boards for now, but when other peripherals are available for mx31 the differences are going to grow. v2: takes Sascha's comments into account Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13mx31: add pin definition for LCDValentin Longchamp
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13mxc: first set GPIO level, then switch direction to outputGuennadi Liakhovetski
Make sure not to create spurious pulses on GPIOs, when configuring them as output: first set required level, then switch direction. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13arm/imx: Kconfig beautificationHolger Schurig
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] iommux mx3: Add pin definitions for I2CSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MXC: add pwm driver for i.MX SoCsSascha Hauer
This driver has been tested on MX27/MX31. It should work on MX1/MX1 aswell, but the actual setting of the PWM is missing so far. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13imxfb: add platform specific init/exit functionsSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13mx31: rework of iomux supportValentin Longchamp
This new implemenatation avoids that two physical pins are claimed by the same driver (also with the the gpr hardware modes). The gpio kernel lib is also called when a capable gpio pin is assigned its gpio function. The mxc_iomux_mode function is still here for backward compatibility but should not be used anymore. V2: In the precendent revision, the iomux code was claiming a pin when its hardware mode was changed. This was uncorrect: when the hardware mode is changed, the pin must still be claimed through the iomux. In order to have a pin working in mode hw2, we must fist issue the mxc_iomux_set_gpr call and then the corresponding mxc_iomux_mode calls with the FUNC mode (usually done with mxc_iomux_setup_multiple_pins). The reverse calls must be done to fee the pins. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13mx31ads: Fix build for missing mx31.hMark Brown
Several of the macros in mx31ads.h depend on mx31.h which is no longer included in quite so many standard headers as it once was. Include it directly so we can build. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13arm/imx21: Framebuffer support for i.MX21Holger Schurig
This patch mimicks what Martin wrote on the mailing list: * move arch/arm/mach-imx/include/mach/imxfb.h into arch/arm/mach-mxc/include/mach/imxfb.h * changes Kconfig so that CONFIG_FB_IMX is selectable * adds a platform device (copied from some pengutronix patches) Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13arm/imx21: clock support for i.MX21Holger Schurig
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com> Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13arm/imx2x: split i.MX21/i.MX27 register definitionsHolger Schurig
* define new CONFIG_ARCH_MX21 (this one is currently mutually exclusive to CONFIG_ARCH_MX27, but this might change) * splits one header file. Memory definitions, interrupt sources, DMA channels are split into common part, i.MX27 specific and i.MX21 specific. * guard access to UART5/UART6, which don't exist on i.MX21 Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13arm/imx2x: removes a bunch of sparse-warningsHolger Schurig
Here are some of the warnings that get fixed by this: > 200 times: warning: cast adds address space to expression (<asn:2>) twelve times: warning: symbol 'xxx' was not declared. Should it be static two times: warning: symbol 'clock' shadows an earlier one five times: warning: incorrect type in initializer (different address spaces) Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MX27 Clock reworkSascha Hauer
This changes MX27 to use common clkdev. It also cleans up MX27 clock support to be more readable. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MXC: add clkdev supportSascha Hauer
This patch only adds general clkdev support without actually switching any MXC architecture to clkdev. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MXC: remove _clk suffix from clock namesSascha Hauer
The context makes it clear already that these are clocks, so there's no need for such a suffix. This patch only changes the clocks actually used in the tree. The remaining clocks are renamed in the subsequent architecture specific patches. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MXC: rework timer/clock initialisationSascha Hauer
- rename mxc_clocks_init to architecture specific versions. This allows us to have more than one architecture compiled in. - call mxc_timer_init from clock initialisation instead from board code Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13[ARM] MXC: Use a single function for decoding a PLLSascha Hauer
We had 3 versions of this function in clock support for MX1/2/3 Use a single one instead. I picked the one from the MX3 as it seems to calculate more accurate as the other ones. Also, on MX27 and MX31 mfn can be negative, this hasn't been handled correctly on MX27 since now. This patch has been tested on MX27 and MX31 and produces the same clock frequencies for me. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13arm/imx21: add kbuild support for the Freescale i.MX21Holger Schurig
* adds Kconfig variables * specifies different physical address for i.MX21 because of the different memory layouts * disables support for UART5/UART6 in the i.MX serial driver (the i.MX21 doesn't have those modules) Based on code from "Martin Fuzzey" <mfuzzey@gmail.com> Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-03-13arm/imx2x: new IOMUX definitionsHolger Schurig
* removed iomux-mx1-mx2.h completely * distributes the former contents to four different files (iomux-mx1.h, iomux-mx21.h, iomux-mx27.h and the file iomux-mx2x.h, which is common to both i.MX21 and i.MX27). * adds all documented IOMUX definitions for i.MX21 and i.MX27 * fixes a few that were wrong (PD14_AOUT_FEC_CLR, PE16_AF_RTCK). * don't silenly include <linux/io.h> * and fixes all collateral damage from above Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-02-26i.MX31: framebuffer driverGuennadi Liakhovetski
This is a framebuffer driver for i.MX31 SoCs. It only supports synchronous displays, vertical panning supported, no overlay support. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-02-26Revert "i.MX31: framebuffer driver"Dan Williams
This reverts commit 86528da229a448577a8401a17c295883640d336c. This version of the patch was tab-to-space corrupted before application. Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-02-21Merge branch 'dma' into develRussell King
Conflicts: arch/arm/plat-mxc/dma-mx1-mx2.c
2009-02-02mmc: Add a MX2/MX3 specific SDHC driverSascha Hauer
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically the same as in the MX1, but unlike the MX1 controller the MX2 controller just works as expected. Since the MX1 driver has more workarounds for bugs than anything else I had no success with supporting MX1 and MX2 in a sane way in one driver. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2009-01-21i.MX31: framebuffer driverGuennadi Liakhovetski
This is a framebuffer driver for i.MX31 SoCs. It only supports synchronous displays, vertical panning supported, no overlay support. Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-01-19i.MX31: Image Processing Unit DMA and IRQ driversGuennadi Liakhovetski
i.MX3x SoCs contain an Image Processing Unit, consisting of a Control Module (CM), Display Interface (DI), Synchronous Display Controller (SDC), Asynchronous Display Controller (ADC), Image Converter (IC), Post-Filter (PF), Camera Sensor Interface (CSI), and an Image DMA Controller (IDMAC). CM contains, among other blocks, an Interrupt Generator (IG) and a Clock and Reset Control Unit (CRCU). This driver serves IDMAC and IG. They are supported over dmaengine and irq-chip APIs respectively. IDMAC is a specialised DMA controller, its DMA channels cannot be used for general-purpose operations, even though it might be possible to configure a memory-to-memory channel for memcpy operation. This driver will not work with generic dmaengine clients, clients, wishing to use it must use respective wrapper structures, they also must specify which channels they require, as channels are hard-wired to specific IPU functions. Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-01-07USB: add imx udc gadget driverDarius Augulis
Implementation of USB device driver integrated in Freescale's i.MXL processor. Adds USB device driver for i.MXL. Signed-off-by: Darius Augulis <augulis.darius@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-02Merge branch 'cpus4096-for-linus-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits) x86: export vector_used_by_percpu_irq x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and() sched: nominate preferred wakeup cpu, fix x86: fix lguest used_vectors breakage, -v2 x86: fix warning in arch/x86/kernel/io_apic.c sched: fix warning in kernel/sched.c sched: move test_sd_parent() to an SMP section of sched.h sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0 sched: activate active load balancing in new idle cpus sched: bias task wakeups to preferred semi-idle packages sched: nominate preferred wakeup cpu sched: favour lower logical cpu number for sched_mc balance sched: framework for sched_mc/smt_power_savings=N sched: convert BALANCE_FOR_xx_POWER to inline functions x86: use possible_cpus=NUM to extend the possible cpus allowed x86: fix cpu_mask_to_apicid_and to include cpu_online_mask x86: update io_apic.c to the new cpumask code x86: Introduce topology_core_cpumask()/topology_thread_cpumask() x86: xen: use smp_call_function_many() x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c ... Fixed up trivial conflict in kernel/time/tick-sched.c manually
2009-01-02[ARM] dma: remove usage of dmamode_t from MXC platform supportRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-18[ARM] MXC: do not include mach/hardware.h from mach/memory.hSascha Hauer
Instead of including other header files, define PHYS_OFFSET directly Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-18[ARM] MXC: do not include mach/hardware.h from mach/timex.hSascha Hauer
Instead of including other header files, define CLOCK_TICK_RATE directly Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-18[ARM] MXC: remove dependency to other include files from irqs.hSascha Hauer
This patch removes the inclusion of mach/hardware.h from mach/irqs.h and switches to more meaningful names for the irq related macros. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-18[ARM] MX1/MX2 DMA: add missing local_irq_restore()Sascha Hauer
This patch adds a missing call to local_irq_restore() and fixes some compiler warnings about unused variables for MX1. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-18[ARM] MX1: Add missing selection of ARM920TSascha Hauer
The MX1 only has one possible CPU type, ARM920T. Select it in Kconfig. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16Unused variable 'reg' removed.Claudio Scordino
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16patch-mxc-fiqPaulius Zaleckas
Drivers which are going to use it will have to select it and use mxc_set_irq_fiq() to set FIQ mode for this interrupt. Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16patch-mx1-mtd-xipDarius Augulis
Adds MTD XIP support for ARCH_MX1. Signed-off-by: Darius Augulis <augulis.darius@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16patch-mxc-add-ARCH_MX1Paulius Zaleckas
Adds MX1 architecture to platform MXC. It will supersede mach-imx and let it die. Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by: Darius Augulis <augulis.darius@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16patch-iomux-mx1-mx2-cleanupDarius Augulis
Fix GIUS register setup in the mxc_gpio_mode(). Signed-off-by: Darius Augulis <augulis.darius@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16MX31: UART5 pins definitionValentin Longchamp
pins definition for UART5 when used in alternate mode 2 Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16MX31: definitions for UART2 pinsValentin Longchamp
UART2 pins when used in functionnal mode Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16Add basic support for MX31PDK board.Fabio Estevam
Add basic support to the MX31PDK development board, also known as MX31 3DS or MX31 3-stack board (http://www.freescale.com/imx31pdk). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: sascha Hauer <s.hauer@pengutronix.de>
2008-12-16[ARM] MX3 iomux: add more pin definitionsSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16[ARM] MX1/MX2: simplify mxc_gpio_setup_multiple_pinsSascha Hauer
mxc_gpio_setup_multiple_pins used to take several ALLOC_MODE flags. Most of them are unused, so simplify the function by removing the flags. Also, instead of using a confusing MXC_GPIO_ALLOC_MODE_RELEASE flag in a function having alloc in its name, add a mxc_gpio_release_multiple_pins function. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16[ARM] MX27: add i.MX27 SDHC1 and SDHC2 GPIO declarationsJulien Boibessot
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-16MX27: Add USB pin function definesSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-29 23:09:24 +0000