| Age | Commit message (Collapse) | Author |
|---|
|
These functions are undefined at first use which causes the build to
fail. Just push the definitions forward, for now. This file needs to
be cleaned up a good bit, in general, so we'll put in a better fix at
that time. For now, this builds, at least...
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This file is OpenMoko specific and didn't get moved in the big file
move. Move it to arch/arm/mach-s3c2410/include/mach where it belongs
and fix the references to it.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
This patch removes a large number of #ifdefs that switch on machine
model. Where applicable, the machine_is_* idiom is favoured; this
mainly makes the code easier to read, but it does have some other
advantages, too.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Problems building with GTA01 disabled in config come down to not selecting the
common CONFIG for GTAXX with GTA02, and GTA01-specific gps stuff.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
|
|
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This patch uses the new glamo-mci slow clock ratio
patch in order to dynamically reduce SD Card clock
rate when the GPS unit is powered on GTA02.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
During the suspend current reduction campaign on suspend I
forced the GPS UART to be GPIO and to drive 0 into the GPS
unit so we would not burn current there. On resume it lets
the pins act as UARTs again. But really, we should do this
all the time that the GPS unit is off, lest we leak it
enough power to hold internal state and make trouble.
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Created an attachment (id=593) / from BZ#79
Updated patch to preserve the power state of the GPS on the GTA01
Currently the GPS is powered up after a suspend/resume occurs. This patch will
only power the GPS back up if it was powered up when the GTA01 suspended.
Signed-off-by: Mike Westerhof <mwester@dls.net>
|
|
- Any setting of any PIN on bank B will undo the LED setting.
Introduce neo1973_gpb_set_pin to set the PIN in a way not losing
the LED or any other shadowed setting.
- Update users of GPBXY for gta01 and gta02.
Signed-Off-By: Holger Freyther <zecke@openmoko.org>
|
|
Signed-Off-By: Holger Freyther <zecke@openmoko.org>
|
|
Similar to the neo1974_pm_gsm.c keep a static struct around. On suspend
we will save the current power state, on resume we will use this
information to enable power of the GPS only when it was powered on before.
This is passing basic tests with screen /dev/ttySAC1 on suspend and resume.
Only do this for the GTA02 as I don't have a gllin setup for the GTA01
I wonder why the suspend and resume code is not using gps_pwron_set and why
for the GTA02 we need to keep the state of the GPIOs, this should be done
by the s3c code.
Signed-Off-by: Holger Frether <zecke@openmoko.org>
|
|
We used to drive output high into GPS unit in suspend
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
[PATCH] Neo1973 GPS / GSM / Bluetooth power control via sysfs
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
