| Age | Commit message (Collapse) | Author |
|---|
|
Allowing us to make the Kconfig a little bit saner.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch provides initial support for CPU frequency scaling on the
Samsung S3C ARM processors. Currently only S3C6410 processors are
supported, though addition of another data table with supported clock
rates should be sufficient to enable support for further CPUs.
Use the regulator framework to provide optional support for DVFS in
the S3C cpufreq driver. When a software controllable regulator is
configured the driver will use it to lower the supply voltage when
running at a lower frequency, giving improved power savings.
When regulator support is disabled or no regulator can be obtained
for VDDARM the driver will fall back to scaling only the frequency.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Merge branch 'next-s3c64xx-dma2' into for-rmk-devel
Conflicts:
arch/arm/plat-s3c64xx/Makefile
|
|
Add support for the DMA blocks in the S3C64XX series of CPUS,
which are based on the ARM PL080 PrimeCell system.
Unfortunately, these DMA controllers diverge from the PL080
design by adding another DMA controller register and
configuration for OneNAND.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for S3C6400 SDHCI channels 0 and 1, making
the GPIO code common to both S3C6400 and S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for saving the state of the IRQ registers over suspend.
This requires moving the S3C64XX UART registers into <plat/regs-serial.h>
and adding irq-pm.c which saves the state of all the IRQ registers.
The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and
IRQ_EINT_GROUP registers as it was easier than adding three different
files. Also ensuring that all the registers are restored to the same
state as before suspend is considered to be the best thing to do.
Note, we do not suspend the VIC here, this is done by the VIC driver
itself.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add the initial support for the S3C64XX based systems to use
suspend-to-RAM to sleep.
Includes basic debugging for use with the SMDK6410 usign the
LEDs on the baseboard.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add a standard helper to configure the LCD output pins for a 24BPP
display with VSYNC/HSYNC/VDEN.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add common gpio setup for i2c bus 1 on all current
S3C64XX architectures.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add the necessary device initialisation information
for I2C device 0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add gpiolib registration for the GPIOs available on the
S3C64XX platform
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add the necessary code to support IRQ_EINT(x) on
the S3C64XX series of CPUs.
Note, since there is no GPIO configuration support
in the kernel, the irq set_type method does not
configure the relevant pin to interrupt.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add the PLL clock initialisation and clock registration
and include the clocks sourced via CLKDIVx for most of
the on-chip peripherals.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add the initial clocks definitions for the s3c6400
and s3c6410. Move the epll and ext clock from the
s3c2443 support into the common code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add the common initialisation code for both the
S3C6400 and S3C6410, the UART registration.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add and initialise the two VIC (PL192) found on
the S3C64XX series CPUs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Initialise the basic physical to virtual mappings and
then detect the CPU that the system is being run on so
that the cpu code code can call the correct initialisation
code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add resources and information for the UART deviecs
on the S3C64XX CPUs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add the initial PLAT_S3C64XX support files
and directory structure.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
