aboutsummaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Expand)Author
2008-01-26ARM kprobes: special hook for the kprobes breakpoint handlerNicolas Pitre
2008-01-26ARM kprobes: prevent some functions involved with kprobes from being probedNicolas Pitre
2008-01-26ARM kprobes: don't let a single-stepped stmdb corrupt the exception stackNicolas Pitre
2008-01-26ARM kprobes: add the kprobes hook to the page fault handlerNicolas Pitre
2008-01-26ARM kprobes: core codeAbhishek Sagar
2008-01-26ARM kprobes: instruction single-stepping supportQuentin Barnes
2008-01-26[ARM] pxa: skip registers saving/restoring if entering standby modeeric miao
2008-01-26[ARM] pxa: fix PXA27x resumeRussell King
2008-01-26[ARM] pxa: Avoid fiddling with CKEN register on suspendRussell King
2008-01-26[ARM] pxa: Add PXA3 standby code hooked into the IRQ wake schemeRussell King
2008-01-26[ARM] pxa: Add zylonite MFP wakeup configurationsRussell King
2008-01-26[ARM] pxa: program MFPs for low power mode when suspendingRussell King
2008-01-26[ARM] pxa: make MFP configuration processor independenteric miao
2008-01-26[ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functionseric miao
2008-01-26[ARM] pxa: omit PXA25x or PXA27x standby/sleep code as appropriateRussell King
2008-01-26[ARM] pxa: clean up pxa{27x,25x}_init_pm() to empty if CONFIG_PM not definederic miao
2008-01-26[ARM] pxa: move memory controller registers into pxa2xx-regs.hRussell King
2008-01-26[ARM] pxa: increase size of memory mappingRussell King
2008-01-26[ARM] pxa: move pxa27x_device_ohci out of pxa27x.c for use with pxa3xxeric miao
2008-01-26[ARM] pxa: add clk of CKEN_USBHOST for pxa3xxeric miao
2008-01-26[ARM] pxa: ensure SSP TX FIFO is empty instead of not full for pxa3xxeric miao
2008-01-26[ARM] pxa: mmc: add 3rd host controller support for pxa310Bridge Wu
2008-01-26[ARM] pxa: mmc: add 2nd host controller support for pxa3xxBridge Wu
2008-01-26[ARM] pxa: mmc: add 1st host controller support for pxa3xxBridge Wu
2008-01-26[ARM] pxa: create arch/arm/mach-pxa/device.c for all on-chip deviceseric miao
2008-01-26[ARM] 4711/1: pxa: mmc: move DMA specific code to platform layerBridge Wu
2008-01-26[ARM] pxa: add cpufreq supportRussell King
2008-01-26[ARM] pxa: initialise SSP earlierRussell King
2008-01-26[ARM] pxa: only register "cpld_irq" for the correct platformRussell King
2008-01-26[ARM] pxa: make pxa2xx_spi driver use ssp_request()/ssp_free()eric miao
2008-01-26[ARM] pxa: use __raw_writel()/__raw_readl() for ssp_xxxx()eric miao
2008-01-26[ARM] pxa: move SSP register definitions from pxa-regs.h to regs-ssp.heric miao
2008-01-26[ARM] pxa: define "struct ssp_device" and add ssp_request()/ssp_free()eric miao
2008-01-26[ARM] pxa: add ssp devices and clk support for pxa25x/pxa27x/pxa3xxeric miao
2008-01-26[ARM] pxa: define SSP platform devices for pxa2xx/pxa3xxeric miao
2008-01-26[ARM] pxa: Don't wind OSCR backwards over suspend/resumeRussell King
2008-01-26[ARM] pxa: remove periodic mode emulation supportRussell King
2008-01-26[ARM] pxa: mainstone: update backlight to use the backlight infrastructureRussell King
2008-01-26[ARM] pxa: avoid always registering MMC, I2C, IrDA and framebuffer devicesRussell King
2008-01-26[ARM] Orion: implement power-off method for QNAP TS-109/209Herbert Valerio Riedel
2008-01-26[ARM] Orion: add support for QNAP TS-109/TS-209Byron Bradley
2008-01-26[ARM] Orion: I2C supportHerbert Valerio Riedel
2008-01-26[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323Martin Michlmayr
2008-01-26[ARM] Orion defconfigTzachi Perelstein
2008-01-26[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323Herbert Valerio Riedel
2008-01-26[ARM] Orion: MV88F5181 support bitsHerbert Valerio Riedel
2008-01-26[ARM] Orion: Buffalo/Revogear Kurobox Pro supportRonen Shitrit
2008-01-26[ARM] OrionNAS RD board supportRonen Shitrit
2008-01-26[ARM] Orion: support for Marvell Orion-2 (88F5281) Development BoardTzachi Perelstein
2008-01-26[ARM] Orion: common platform setup for Gigabit Ethernet portTzachi Perelstein
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 09:31:54 +0000