aboutsummaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2010-01-08omap1: Add 7xx clocks and pin muxes for SPICory Maccarrone
Commit 35c9049b27040d09461bc90928ad770be7ddf661 added drivers/spi/omap_spi_100k.c. This patch add the related clocks and pin muxing entries to make the driver work on omap7xx platforms. Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08omap: Remove uninitialized warning for gpio.cTony Lindgren
Flags is not used on 15xx. Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08omap: &&/|| confusion in iommu_put()Roel Kluin
obj can't be both NULL and be an error pointer. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08omap: gpio: Simultaneously requested rising and falling edgeCory Maccarrone
Some chips, namely any OMAP1 chips using METHOD_MPUIO, OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO interrupts in both rising and falling edge directions -- they can only respond to one direction or the other, depending on how the ICR is configured. Additionally, current code forces rising edge detection if both flags are specified: if (trigger & IRQ_TYPE_EDGE_RISING) l |= 1 << gpio; else if (trigger & IRQ_TYPE_EDGE_FALLING) l &= ~(1 << gpio); else goto bad; This change implements a toggle function that will modify the ICR to flip the direction of interrupt for IRQs that are requested with both rising and falling flags. The toggle function is not called for chips and GPIOs it does not apply to through the use of a flip_mask that's added on a per-bank basis. The mask is only set for those GPIOs where a toggle is necessary. Edge detection starts out the same as above with FALLING mode first. The toggle happens on EACH interrupt; without it, we have the following sequence of actions on GPIO transition: ICR GPIO Result 0x1 0 -> 1 (rising) Interrupt 0x1 1 -> 0 (falling) No interrupt (set ICR to 0x0 manually) 0x0 0 -> 1 (rising) No interrupt 0x0 1 -> 0 (falling) Interrupt That is, with the ICR set to 1 for a gpio, only rising edge interrupts are caught, and with it set to 0, only falling edge interrupts are caught. If we add in the toggle, we get this: ICR GPIO Result 0x1 0 -> 1 (rising) Interrupt (ICR set to 0x0) 0x0 1 -> 0 (falling) Interrupt (ICR set to 0x1) 0x1 0 -> 1 ... so, both rising and falling are caught, per the request for both (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING). Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08omap: McBSP: Fix possible port lockoutJanusz Krzysztofik
In its current form, the omap_mcbsp_request() function can return after irq_request() failure without any cleanups, effectively locking out the port forever with clocks left running. Fix it. Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-04ARM: Merge next-simtecBen Dooks
Merge branch 'next-simtec' into for-linus/samsung
2009-12-24ARM: dma-isa: request cascade channel after registering itRussell King
We can't request the cascade channel before it's been registered, so move it afterwards. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-24ARM: footbridge: trim down old ISA rtc setupRussell King
This fixes a "start_kernel(): bug: interrupts were enabled early". rtc_cmos now takes care of initializing the ISA RTC and reading the current time and date from it; there's no need to repeat that here, thereby causing interrupts to be enabled too early. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-24ARM: fix PAGE_KERNELRussell King
PAGE_KERNEL should not be executable; any area marked executable can be prefetched into the instruction cache. We don't want vmalloc areas to be read in this way. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-23ARM: S3C: Fix NAND device registration by s3c_nand_set_platdata().Ben Dooks
Fix two bugs in s3c_nand_set_platdata() where thet device's platform data was not set, and the wrong error check was being performed on the return of s3c_nand_copy_set(). Fixes the following OOPS: Unable to handle kernel NULL pointer dereference at virtual address 00000004 PC is at s3c24xx_nand_probe+0x234/0x594 Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-12-23ARM: Fix wrong shared bit for CPU write buffer bug testRussell King
It is unpredictable to have the same memory mapped using different shared bit settings for ARMv6 and ARMv7 CPUs. Fix this for the CPU write buffer bug test. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-23ARM: S3C24XX: touchscreen device definitionArnaud Patard
Add definition for the touchscreen driver platform data and initial support for the H1940 machine. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-12-23ARM: mach-bast: add NAND_SCAN_SILENT_NODEV to optional devicesBen Dooks
Add the NAND_SCAN_SILENT_NODEV to the optional NAND devices that may not be fitted to the board Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Simtec Linux Team <linux@simtec.co.uk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-12-23ARM: mach-osiris: add NAND_SCAN_SILENT_NODEV to optional devicesBen Dooks
Add the NAND_SCAN_SILENT_NODEV to the optional NAND devices that may not be fitted to the board Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Simtec Linux Team <linux@simtec.co.uk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-12-22ARM: 5857/1: ARM: dmabounce: fix buildMike Rapoport
Commit f74f7e57ae9fa12b2951ae62ce3557799b318399 (ARM: use flush_kernel_dcache_area() for dmabounce) has broken dmabounce build: CC arch/arm/common/dmabounce.o arch/arm/common/dmabounce.c: In function 'unmap_single': arch/arm/common/dmabounce.c:315: error: implicit declaration of function '__cpuc_flush_kernel_dcache_area' make[2]: *** [arch/arm/common/dmabounce.o] Error 1 Fix it. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-22ARM: 5856/1: Fix bug of uart0 platfrom data for nuc900wanzongshun
Fix bug of uart0 platfrom data for nuc900 Signed-off-by: lijie <eltshanli@gmail.com> Signed-off-by: Wan ZongShun <mcuos.com@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-22ARM: 5855/1: putc support for nuc900wanzongshun
putc support for nuc900 Signed-off-by: lijie <eltshanli@gmail.com> Signed-off-by: Wan ZongShun <mcuos.com@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-22ARM: 5854/1: fix compiling error for NUC900wanzongshun
fix compiling error for NUC900 Signed-off-by: lijie <eltshanli@gmail.com> Signed-off-by: Wan ZongShun <mcuos.com@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-22ARM: 5849/1: ARMv7: fix Oprofile events countJean PIHET
On Oprofile ARMv7 the PMNC_D bit was set to lower the PMU IRQs and so to decrease the risk of errata #628216 from appearing. The effect of setting the PMNC_D bit is that the CCNT counter is divided by 64, making the program counter events count inaccurate. The new OMAP3 r4 cores should have that errata fixed. The PMNC_D bit should not be set, this patch fixes it. Signed-off-by: Jean Pihet <jpihet@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-18ARM: Kill CONFIG_CPU_32Russell King
26-bit ARM support was removed a long time ago, and this symbol has been defined to be 'y' ever since. As it's never disabled anymore, we can kill it without any side effects. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-18ARM: Convert VFP/Crunch/XscaleCP thread_release() to exit_thread()Russell King
This avoids races in the VFP code where the dead thread may have state on another CPU. By moving this code to exit_thread(), we will be running as the thread, and therefore be running on the current CPU. This means that we can ensure that the only local state is accessed in the thread notifiers. Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-18ARM: 5853/1: ARM: Fix build break on ARM v6 and v7Anand Gadiyar
Commit 2c9b9c849 added an argument to __cpuc_flush_dcache_page and renamed it. Update a caller of the old function to fix this build error: CC arch/arm/mm/copypage-v6.o arch/arm/mm/copypage-v6.c: In function 'v6_copy_user_highpage_nonaliasing': arch/arm/mm/copypage-v6.c:51: error: implicit declaration of function '__cpuc_flush_dcache_page' make[1]: *** [arch/arm/mm/copypage-v6.o] Error 1 make: *** [arch/arm/mm] Error 2 Reported-by: Jinsung Yang <jsgood.yang@samsung.com> Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-17Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: OMAP3: serial - fix bug introduced in mfd: twl: fix twl4030 rename for remaining driver, board files USB ehci: replace mach header with plat omap3: Allow EHCI to be built on OMAP3
2009-12-17Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6Linus Torvalds
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: spi: spi_txx9.c: use resource_size() spi: spi_sh_sci.c: use resource_size() spi: spi_mpc8xxx.c: use resource_size() spi: spi_bfin5xx.c: use resource_size() spi: atmel_spi.c: use resource_size() spi: Add s3c64xx SPI Controller driver atmel_spi: fix dma addr calculation for len > BUFFER_SIZE spi_s3c24xx: add FIQ pseudo-DMA support spi: controller driver for Designware SPI core spidev: add proper section markers spidev: use DECLARE_BITMAP instead of declaring the array
2009-12-17Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: PCMCIA: fix pxa2xx_lubbock modular build error [ARM] Update mach-types [ARM] pxa: fix no reference of cpu_is_pxa25x() in devices.c [ARM] pxa/cm-x300: add PWM backlight support revert "[ARM] pxa/cm-x300: add PWM backlight support" ARM: use flush_kernel_dcache_area() for dmabounce ARM: add size argument to __cpuc_flush_dcache_page ARM: 5848/1: kill flush_ioremap_region() ARM: cache-l2x0: make better use of background cache handling ARM: cache-l2x0: avoid taking spinlock for every iteration [ARM] Kirkwood: Add LaCie Network Space v2 support ARM: dove: fix the mm mmu flags of the pj4 procinfo
2009-12-17Merge branch 'cache' (early part)Russell King
2009-12-17spi_s3c24xx: add FIQ pseudo-DMA supportBen Dooks
Add pseudo-DMA by FIQ to the S3C24XX SPI driver. This allows the driver to get DMA-like performance where there are either no free DMA channels or when doing transfers that required both TX and RX data paths. Since this patch requires the addition of an assembly file to hold the FIQ code, we rename the module (instead of adding a rename of the .c file to this patch). We expect most users are loading this via udev and thus there should be no change to the userland configuration. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Simtec Linux Team <linux@simtec.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-17Merge branch 'for-33' of git://repo.or.cz/linux-kbuildLinus Torvalds
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits) net: fix for utsrelease.h moving to generated gen_init_cpio: fixed fwrite warning kbuild: fix make clean after mismerge kbuild: generate modules.builtin genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}() score: add asm/asm-offsets.h wrapper unifdef: update to upstream revision 1.190 kbuild: specify absolute paths for cscope kbuild: create include/generated in silentoldconfig scripts/package: deb-pkg: use fakeroot if available scripts/package: add KBUILD_PKG_ROOTCMD variable scripts/package: tar-pkg: use tar --owner=root Kbuild: clean up marker net: add net_tstamp.h to headers_install kbuild: move utsrelease.h to include/generated kbuild: move autoconf.h to include/generated drop explicit include of autoconf.h kbuild: move compile.h to include/generated kbuild: drop include/asm kbuild: do not check for include/asm-$ARCH ... Fixed non-conflicting clean merge of modpost.c as per comments from Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h that needed to be changed to generated/autoconf.h)
2009-12-17Merge branch 'devel' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
2009-12-16OMAP3: serial - fix bug introduced inMika Westerberg
Commit f62349ee9788b1d94c55eb6c291d74a1f69bdd9e had side effect that causes kernel to oops when we are suspending to ram: # echo mem > /sys/power/state WARNING: at kernel/irq/manage.c:858 __free_irq+0x90/0x174() Trying to free already-free IRQ 72 Modules linked in: Backtrace: [<c00328d0>] (dump_backtrace+0x0/0x110) from [<c0347298>] (dump_stack+0x18/0x1c) r7:dfd4be08 r6:c009505c r5:c03fbfd1 r4:0000035a [<c0347280>] (dump_stack+0x0/0x1c) from [<c005a408>] (warn_slowpath_common+0x50/0x68) [<c005a3b8>] (warn_slowpath_common+0x0/0x68) from [<c005a46c>] (warn_slowpath_fmt+0x30) r7:c0474afc r6:00000048 r5:00000000 r4:c0474ac0 [<c005a43c>] (warn_slowpath_fmt+0x0/0x38) from [<c009505c>] (__free_irq+0x90/0x174) r3:00000048 r2:c03fc0ef [<c0094fcc>] (__free_irq+0x0/0x174) from [<c0095184>] (free_irq+0x44/0x64) [<c0095140>] (free_irq+0x0/0x64) from [<c0038100>] (omap_uart_enable_irqs+0x4c/0x90) r7:c034d58c r6:00000003 r5:00000000 r4:c0463028 [<c00380b4>] (omap_uart_enable_irqs+0x0/0x90) from [<c003d8f8>] (omap3_pm_begin+0x1c/0) r5:00000003 r4:00000000 [<c003d8dc>] (omap3_pm_begin+0x0/0x28) from [<c008d008>] (suspend_devices_and_enter+0x) [<c008cfd8>] (suspend_devices_and_enter+0x0/0x1dc) from [<c008d29c>] (enter_state+0xe8) r5:c03f7f46 r4:00000000 [<c008d1b4>] (enter_state+0x0/0x140) from [<c008c8e0>] (state_store+0x9c/0xc4) r7:c034d58c r6:00000003 r5:00000003 r4:c03f7f46 [<c008c844>] (state_store+0x0/0xc4) from [<c01cb2dc>] (kobj_attr_store+0x20/0x24) [<c01cb2bc>] (kobj_attr_store+0x0/0x24) from [<c0119420>] (sysfs_write_file+0x114/0x14) [<c011930c>] (sysfs_write_file+0x0/0x148) from [<c00cb298>] (vfs_write+0xb8/0x164) [<c00cb1e0>] (vfs_write+0x0/0x164) from [<c00cb408>] (sys_write+0x44/0x70) r8:4001f000 r7:00000004 r6:df81bd00 r5:00000000 r4:00000000 [<c00cb3c4>] (sys_write+0x0/0x70) from [<c002f040>] (ret_fast_syscall+0x0/0x38) r8:c002f204 r7:00000004 r6:401fa5e8 r5:4001f000 r4:00000004 This is due the fact that uart_list list was populated in omap_serial_early_init() and omap_uart_enable_irqs() went through this list even when serial idle wasn't enabled for all uarts. This patch moves the code that populates the uart_list and enables uart clocks into omap_serial_init_port(). Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-16mfd: twl: fix twl4030 rename for remaining driver, board filesBalaji T K
Recent drivers/mfd/twl4030* renames to twl broke compile for various boards as the series was missing a patch to change the board-*.c files. This patch renames include twl4030.h to include twl.h and also renames twl4030_i2c_ routines. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-16[ARM] Update mach-typesRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-16Merge branch 'for-rmk' of git://git.marvell.com/orionRussell King
2009-12-16Merge branch 'module' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus * 'module' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: modpost: fix segfault with short symbol names module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y Kbuild: clear marker out of modpost module: make MODULE_SYMBOL_PREFIX into a CONFIG option ARM: unexport symbols used to implement floating point emulation ARM: use unified discard definition in linker script x86: don't export inline function sparc64: don't export static inline pci_ functions
2009-12-16Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits) Input: ALPS - add interleaved protocol support (Dell E6x00 series) Input: keyboard - don't override beep with a bell Input: altera_ps2 - fix test of unsigned in altera_ps2_probe() Input: add mc13783 touchscreen driver Input: ep93xx_keypad - update driver to new core support Input: wacom - separate pen from express keys on Graphire Input: wacom - add defines for data packet report IDs Input: wacom - add support for new LCD tablets Input: wacom - add defines for packet lengths of various devices Input: wacom - ensure the device is initialized properly upon resume Input: at32psif - do not sleep in atomic context Input: i8042 - add Gigabyte M1022M to the noloop list Input: i8042 - allow installing platform filters for incoming data Input: i8042 - fix locking in interrupt routine Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad Input: document use of input_event() function Input: sa1111ps2 - annotate probe() and remove() methods Input: ambakmi - annotate probe() and remove() methods Input: gscps2 - fix probe() and remove() annotations Input: altera_ps2 - add annotations to probe and remove methods ...
2009-12-16Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: ppc440spe-adma: adds updated ppc440spe adma driver iop-adma.c: use resource_size() dmaengine: clarify the meaning of the DMA_CTRL_ACK flag sh: stylistic improvements for the DMA driver dmaengine: fix dmatest to verify minimum transfer length and test buffer size sh: DMA driver has to specify its alignment requirements Add COH 901 318 DMA block driver v5
2009-12-16Merge git://git.infradead.org/mtd-2.6Linus Torvalds
* git://git.infradead.org/mtd-2.6: (90 commits) jffs2: Fix long-standing bug with symlink garbage collection. mtd: OneNAND: Fix test of unsigned in onenand_otp_walk() mtd: cfi_cmdset_0002, fix lock imbalance Revert "mtd: move mxcnd_remove to .exit.text" mtd: m25p80: add support for Macronix MX25L4005A kmsg_dump: fix build for CONFIG_PRINTK=n mtd: nandsim: add support for 4KiB pages mtd: mtdoops: refactor as a kmsg_dumper mtd: mtdoops: make record size configurable mtd: mtdoops: limit the maximum mtd partition size mtd: mtdoops: keep track of used/unused pages in an array mtd: mtdoops: several minor cleanups core: Add kernel message dumper to call on oopses and panics mtd: add ARM pismo support mtd: pxa3xx_nand: Fix PIO data transfer mtd: nand: fix multi-chip suspend problem mtd: add support for switching old SST chips into QRY mode mtd: fix M29W800D dev_id and uaddr mtd: don't use PF_MEMALLOC mtd: Add bad block table overrides to Davinci NAND driver ... Fixed up conflicts (mostly trivial) in drivers/mtd/devices/m25p80.c drivers/mtd/maps/pcmciamtd.c drivers/mtd/nand/pxa3xx_nand.c kernel/printk.c
2009-12-16elf: kill USE_ELF_CORE_DUMPChristoph Hellwig
Currently all architectures but microblaze unconditionally define USE_ELF_CORE_DUMP. The microblaze omission seems like an error to me, so let's kill this ifdef and make sure we are the same everywhere. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk> Cc: <linux-arch@vger.kernel.org> Cc: Michal Simek <michal.simek@petalogix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-16da850/omap-l138: add callback to control LCD panel powerChaithrika U S
Add the platform specific callback to control LCD panel and backlight power. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-16[ARM] pxa: fix no reference of cpu_is_pxa25x() in devices.cEric Miao
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-12-16[ARM] pxa/cm-x300: add PWM backlight supportIgor Grinberg
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-12-16revert "[ARM] pxa/cm-x300: add PWM backlight support"Eric Miao
Commit db205463fd24c0972ad2c4e4fafb1c76e51b4380 was incorrectly applied, and reverted here to re-apply. Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-12-15omap3: Allow EHCI to be built on OMAP3Olof Johansson
OMAP34XX has EHCI, so select USB_ARCH_HAS_EHCI. Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-15Merge branch 'core-locking-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits) clockevents: Convert to raw_spinlock clockevents: Make tick_device_lock static debugobjects: Convert to raw_spinlocks perf_event: Convert to raw_spinlock hrtimers: Convert to raw_spinlocks genirq: Convert irq_desc.lock to raw_spinlock smp: Convert smplocks to raw_spinlocks rtmutes: Convert rtmutex.lock to raw_spinlock sched: Convert pi_lock to raw_spinlock sched: Convert cpupri lock to raw_spinlock sched: Convert rt_runtime_lock to raw_spinlock sched: Convert rq->lock to raw_spinlock plist: Make plist debugging raw_spinlock aware bkl: Fixup core_lock fallout locking: Cleanup the name space completely locking: Further name space cleanups alpha: Fix fallout from locking changes locking: Implement new raw_spinlock locking: Convert raw_rwlock functions to arch_rwlock locking: Convert raw_rwlock to arch_rwlock ...
2009-12-15Merge git://git.infradead.org/battery-2.6Linus Torvalds
* git://git.infradead.org/battery-2.6: power_supply_sysfs: Handle -ENODATA in a special way wm831x_backup: Remove unused variables gta02: Set pcf50633 charger_reference_current_ma pcf50633: Query charger status directly pcf50633: Properly reenable charging when the supply conditions change pcf50633: Get rid of charging restart software auto-triggering pcf50633: introduces battery charging current control pcf50633: Add ac power supply class to the charger wm831x: Factor out WM831x backup battery charger
2009-12-15Input: ep93xx_keypad - update driver to new core supportH Hartley Sweeten
This driver was merged before the ep93xx core support was added for the keypad clock and acquiring/releasing the necessary gpio's. Now that the proper support is in the ep93xx core this driver needs to be updated to work correctly. Summary of changes: 1) Remove some unused members from the platform data. 2) Remove the custom KEY macro and use the ones available in <linux/input/matrix_keypad.h> 3) Remove the keypad_{readl/writel} macros and just use __raw_{readl/writel} directly. 4) Update the clk_set_rate() call to work with the core support. 5) Cleanup the probe routine and remove some unneeded messages. 6) Use the ep93xx core functions to acquire and release the gpio's. 7) Fix the clk_get() call to get the keypad clock. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-12-15atmel-mci: change use of dma slave interfaceNicolas Ferre
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver. This adds a generic dma_slave pointer to the mci platform structure where we can store DMA controller information. In atmel-mci we use information provided by this structure to initialize the driver (with new helper functions that are architecture dependant). This also adds at32/avr32 chip modifications to cope with this new access method. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15const: constify remaining dev_pm_opsAlexey Dobriyan
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15ARM: unexport symbols used to implement floating point emulationAlan Jenkins
The Kconfigs for in-tree floating point emulation do not allow building as modules. That leaves the Acorn FPEmulator module. I found two public releases of this as a binary module for 2.1 and 2.2 kernels, optimized for ARMV4.[1] If there is a resurgence of interest in this, the symbols can always be re-exported. This allows the EXPORT_SYMBOL_ALIAS() hack to be removed. The ulterior motive here is that EXPORT_SYMBOL_ALIAS() makes it harder to sort the resulting kernel symbol tables. Sorted symbol tables will allow faster symbol resolution during module loading. Note that fp_send_sigs() and fp_printk() are simply aliases for existing exports and add no obvious value. Similarly fp_enter could easily be renamed to kern_fp_enter at the point of definition. Therefore removing EXPORT_SYMBOL_ALIAS will not serve as a material obstacle to re-adding the exports should they be desired in future. Build tested only. [1] http://ftp.arm.linux.org.uk/pub/linux/arm/fpemulator/ Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> CC: Russell King <linux@arm.linux.org.uk> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2009-12-15ARM: use unified discard definition in linker scriptAlan Jenkins
Commit 023bf6f "linker script: unify usage of discard definition" changed the linker scripts for all architectures except for ARM. I can find no discussion about this ommision, so here are the changes for ARM. These changes are exactly parallel to the ia64 case. "ia64 is notable because it first throws away some ia64 specific subsections and then include the rest of the sections into the final image, so those sections must be discarded before the inclusion." Not boot-tested. In build testing, the modified linker script generated an identical vmlinux file. [I would like to be able to rely on this unified discard definition. I want to sort the kernel symbol tables to allow faster symbol resolution during module loading. The simplest way appears to be to generate sorted versions from vmlinux.o, link them in to vmlinux, _and discard the original unsorted tables_. This work is driven by my x86 netbook, but it is implemented at a generic level. It is possible it will benefit some ARM systems also.] Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by-without-testing: Tejun Heo <tj@kernel.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-30 01:02:54 +0000