| Age | Commit message (Collapse) | Author |
|---|
|
We really want to be using the memory type table in ioremap, so we
only have to do the CPU type fixups in one place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than our three separate loops to setup mappings (by page
mappings up to a section boundary, then section mappings, and the
remainder by page mappings) convert this to a more conventional
Linux style of a loop over each page table level.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Catalin Marinas at ARM Ltd says:
> The CPU architects in ARM intended supersections only as a way to map
> addresses >= 4GB. Supersections are not mandated by the architecture
> and there is no easy way to detect their hardware support at run-time
> (other than checking for a specific core). From the analysis done in
> ARM, there wasn't a clear performance gain by using supersections
> rather than sections (no significant improvement in the TLB misses).
Therefore, we should avoid using supersections unless there's a real
need (iow, we're mapping addresses >= 4GB).
This means that we can simplify create_mapping() a bit since we will
only use supersection mappings for addresses >= 4GB, which means that
the physical, virtual and length must be multiples of the supersection
mapping size.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There's now no need to carry around each protection separately.
Instead, pass around the pointer to the entry in the mem_types
array which we're interested in.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than combining the domain for a particular memory type with
the protection information each time we want to use it, do so when
we fix up the mem_type array at initialisation time.
Rename struct mem_types to be mem_type - each structure is one
memory type description, not several.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Lots of places in arch/arm were needlessly including linux/ptrace.h,
resumably because we used to pass a struct pt_regs to interrupt
handlers. Now that we don't, all these ptrace.h includes are
redundant.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Update defconfig to the latest kernel version
and enable the h1940 LED driver
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
dma_channel_active() is used by some modules and is part of our
DMA API, so export it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix the NAND flash timings on the AT91SAM9260.
The current timings lead to the detection of a number of bad blocks.
These timings are now set the same as on the AT91SAM9263.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4278/1: configure pxa27x I2C SCL as "input"
[ARM] 4272/1: Missing symbol h1940_pm_return fix
[ARM] 4235/1: ns9xxx: declare the clock functions as "const"
[ARM] 4271/1: iop32x: fix ep80219 detection (support iq80219 platforms)
[ARM] 4270/2: mach-s3c2443/irq.c off by one error in dma irqs
|
|
Added missing ifdefs, to make kernel linkable without the PM support.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4264/1: ldrex/strex syntax errors with recent compilers
[ARM] Fix breakage caused by 72486f1f8f0a2bc828b9d30cf4690cf2dd6807fc
|
|
Build fix: sa1100/generic.c should already have included <asm/gpio.h>,
but it didn't ... causing a build problem with a recent patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
An iq80219 is a board with an iq31244 layout and an 80219 processor. It
breaks the current assumption that all 80219 processors run on ep80219
platforms. This patch adds the "force_ep80219" option to the kernel to
override boot loaders that have passed in the iq31244 id, and adds the
MACHINE_START definition for ep80219.
[ patch assumes that EP80219 has been added to mach-types ]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch corrects an error when demuxing the DMA irq's
DMA1 was used as a base and this should have been DMA0.
Without this fix we do not process DMA0 irq's and the
system effectively locks up in a loop trying the process
the irq it never can.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
72486f1f8f0a2bc828b9d30cf4690cf2dd6807fc inverted the sense for
enabling hotplug CPU controls without reference to any other
architecture other than i386, ia64 and PowerPC. This left
everyone else without hotplug CPU control.
Fix ARM for this brain damage.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Only System PLL clock source is selectable by CSCR_SYSTEM_SEL
bit. MPU PLL is driven by 512*CLK32 for each case.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The minimal bus clock prescaler should be kept at value
selected by the board / boot loader designer.
Switching frequency above startup limit could
lead to the external memory/devices misbehave.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
|
|
The sharpsl_pm code depends on some symbols in the APM emulation code.
Add the dependency for now until a better solution can be found.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix tosa compile failure from commit
32f3f49910c7e228839c1cd144dbed8da342703b
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The Product Manager of the cc9p insist on using the correct product names.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds the delayed application attribute to the dss2 clock. DSS2
can't select the 48MHz APLL with properly with out validating the
configuration as trigged by this flag.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ARM: OMAP: Fix missing #include <linux/workqueue.h> in
board-h2.c resulting in
In file included from arch/arm/mach-omap1/board-h2.c:40:
include/asm/arch/irda.h:27: error: field 'gpio_expa' has
incomplete type
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include missing header for do_div()
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
|
|
Update help text with location of documentation
and duplicate the note on the speed of CRC
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Always allow backtrace when using oprofile on ARM, even if a PMU
isn't present.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use linux/delay.h not asm/delay.h
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Convert 1510->15xx in generic omap code, so that sx1 can work.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add missing includes to board-nokia770 to make it
compile again.
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Workqueue changes for board-h4.c
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When I went to use dmtimer7 it did not seem to work. I noticed that
the base addresses for dmtimers 7 and 8 were set wrong. A simple patch
to correct a small error. Confirmed to fix the problem on an OSK.
Signed-off-by: Matthew Percival <matthew@capgo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Some time ago, the 'lcd_lph8923' device was renamed to 'lcd_mipid' but
the board-nokia770.c file was not updated accordingly, leading to not
working lcd.
This one-liner fixe the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Teach OMAP2 gp timer that HZ isn't always 100.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix warning
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:765: warning: ignoring return value
of 'subsys_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix broken CONFIG_DEBUG_LL. In case of low level debugging
reconfigure some clocks early.
See
http://source.mvista.com/git/gitweb.cgi?p=linux-omap-2.6.git;a=commitdiff;h=3bfb289ccc6c4624fd5ff0381546935e105f4093
too.
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix warning
arch/arm/mach-omap2/timer-gp.c: In function
'omap2_gp_timer_init':
arch/arm/mach-omap2/timer-gp.c:70: warning: implicit
declaration of function 'setup_irq'
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix warnings
arch/arm/plat-omap/dmtimer.c: In function
'omap_dm_timer_modify_idlect_mask':
arch/arm/plat-omap/dmtimer.c:317: warning: no return
statement in function returning non-void
arch/arm/plat-omap/mailbox.c: In function 'omap_mbox_init':
arch/arm/plat-omap/mailbox.c:231: warning: ignoring return
value of 'class_device_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
No IRQF_TRIGGER set_type function for IRQ 353 (MPUIO)
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This makes serial usable also on omap310, not only 1510.
(changing 1510->15xx)
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
