aboutsummaryrefslogtreecommitdiff
path: root/arch/blackfin
AgeCommit message (Collapse)Author
2007-11-18Blackfin arch: cleanup kernel exception message, don't insult the customer.Robin Getz
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-18Blackfin arch: fix bug kernel not to boot up with mtd filesystemsBernd Schmidt
Revert this patch: move the init sections to the end of memory, so that after they are free, run time memory is all continugous - this should help decrease memory fragementation. When doing this, we also pack some of the other sections a little closer together, to make sure we don't waste memory. To make this happen, we need to rename the .data.init_task section to .init_task.data, so it doesn't get picked up by the linker script glob. Since it causes the kernel not to boot up with mtd filesystems. Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-17Blackfin arch: add AXIS AX88180 Gigabit Ethernet Hardware and Driver to ↵Michael Hennerich
board files Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-18Blackfin arch: print out modules that are loaded if we get a kernel oopsRobin Getz
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-17Blackfin arch: Add assembly function insl_16Michael Hennerich
/* * CPUs often take a performance hit when accessing unaligned memory * locations. The actual performance hit varies, it can be small if the * hardware handles it or large if we have to take an exception and fix * it * in software. * * Since an ethernet header is 14 bytes network drivers often end up * with * the IP header at an unaligned offset. The IP header can be aligned by * shifting the start of the packet by 2 bytes. Drivers should do this * with: * * skb_reserve(NET_IP_ALIGN); * * The downside to this alignment of the IP header is that the DMA is * now * unaligned. On some architectures the cost of an unaligned DMA is high * and this cost outweighs the gains made by aligning the IP header. * * Since this trade off varies between architectures, we allow * NET_IP_ALIGN * to be overridden. */ This new function insl_16 allows to read form 32-bit IO and writes to 16-bit aligned memory. This is useful in above described scenario - In particular with the AXIS AX88180 Gigabit Ethernet MAC. Once the device is in 32-bit mode, reads from the RX FIFO always decrements 4bytes. While on the other side the destination address in SDRAM is always 16-bit aligned. If we use skb_reserve(0) the receive buffer is 32-bit aligned but later we hit a unaligned exception in the IP code. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-23Blackfin arch: use do_div() for the 64bit division as pointed out by BerndMike Frysinger
If you need a 64 bit divide in the kernel, use asm/div64.h. Revert the addition of udivdi3. Cc: Bernd Schmidt <bernd.schmidt@analog.com> Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-17Blackfin arch: fix spurious newline in headerMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-17Blackfin arch: unexport get_wchanAdrian Bunk
The only user of get_wchan I was able to find is the proc fs - and proc can't be built modular. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-18Blackfin arch: remove dump_thread()Adrian Bunk
The only user is the a.out support. It was therefore removed prior to the blackfin merge from all architectures not supporting a.out. Currently, Blackfin doesn't suppport a.out. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-17Blackfin arch: Typo: "CONFIG_RTC_BFIN_MODULE" -> "CONFIG_RTC_DRV_BFIN_MODULE"Robert P. J. Day
i'm *reasonably* confident that this is a typo that should be fixed. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: Dont use cs_change_per_word, since the AD7877 driver doesnt ↵Michael Hennerich
require it anymore; fix bus numbers, fix typos Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: relocate linux/usb_isp1362.h to linux/usb/isp1362.h like in ↵Mike Frysinger
newer linux trees Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: the usb_sl811.h header has been moved to usb/sl811.h so lets ↵Mike Frysinger
use that version now Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: do not include linux/autoconf.hMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: change get_bf537_ether_addr() to bfin_get_ether_addr() since ↵Mike Frysinger
this is not BF537 specific and to better match other Blackfin-specific conventions Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-22Blackfin arch: sharing the board-specific MAC function does not make sense ↵Mike Frysinger
so move it into board-specific files Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: remove useless CONFIG_IRQCHIP_DEMUX_GPIOMike Frysinger
since we have this always turned on now and dont want it off (and hasnt been an option in a while) Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: fix missing newline to fileMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: add BF547 to list of accepted procsMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: move the init sections to the end of memory to help decrease ↵Robin Getz
memory fragementation move the init sections to the end of memory, so that after they are free, run time memory is all continugous - this should help decrease memory fragementation. When doing this, we also pack some of the other sections a little closer together, to make sure we don't waste memory. To make this happen, we need to rename the .data.init_task section to .init_task.data, so it doesn't get picked up by the linker script glob. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-21Blackfin arch: split debug stuff off into Kconfig.debug like everyone elseMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-23Blackfin arch: punt CONFIG_BFIN -- we already have CONFIG_BLACKFINMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: fix indentation -- use tabs, not spacesMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: split board selection off into mach subdirsMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: fix silicon rev display and selection for BF52x/BF54xMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: remove mention of uClinux/no-mmu ... we are just Blackfin LinuxMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: Default config for HV Sistemas H8606 boardJavier Herrero
Signed-off-by: Javier Herrero <jherrero@hvsistemas.es> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-15Blackfin arch: fix bug cplbmgr.S does not exit properly on error conditionRobin Getz
https://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=1685 Ensure that cache/protection is turned back on when we get a fault, and ensure that the initial population of the CPLB tables are correct - that kernel is locked in CPLB tables Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-13Blackfin arch: fix AD7877 bus_num and add support for WM8731 SPI control ↵Michael Hennerich
interface Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-12Blackfin arch: move hard coded pin_req to board fileBryan Wu
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time - move this static things to the blackfin board file - add pin_req array to struct bfin5xx_spi_master - tested on BF537/BF548 with SPI flash Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-12Blackfin arch: fix bux - only reset the PC when necessary, otherwise gdb ↵Robin Getz
gets confused Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-11-12Blackfin arch: ensure we work around ANOMALY_05000261 for null pointersRobin Getz
We currently do not. Also make it easier to handle cplb violations - in traps.c Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-30Blackfin arch: reclaim a few bytes from the end of our init sectionMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-30Blackfin arch: fix libata data struct member from irq_type to irq_flagsMike Frysinger
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-30Blackfin arch: Fix bug set correct baud for spi mmc and enable SPI after DMA.Sonic Zhang
Changes: 1. The baud for spi mmc defined in board file is not used by the old spi driver. A slower value from spi framework is used instead. In latest bug fixing, the correct baud is use which is too high for spi MMC card. 2. SPI is enabled only after DMA is started. 3. MMC detection IRQ is set to 55. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-30Blackfin arch: update board defconfig files according to latest information ↵Bryan Wu
from ADI datasheet Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: ensure that speculative loads of bad pointers don't cause us ↵Robin Getz
to do bad things. Fix/change formatting of a few more things. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: Fix random crash issue found by Michael.Robin Getz
This is fixes a problem where we could jump to the wrong address. By doing a "p0 = reti; jump (p0)". If a different, higher level interrupt came in, just before, rather than returning to the calling function, we would return to a random place in the kernel. This very elegant fix from Bernd grabs the return location off the stack, and places it into P0, so when we do a return, it goes to the correct place. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: fix bug: tell users if the kernel is recovering from a fault ↵Robin Getz
condition Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: add support for checking/clearing overruns in generic purpose ↵Mike Frysinger
Timer API Signed-off-by: Mike Frysinger <michael.frysinger@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: cleanup arch/blackfin/kernel/traps.c handling code.Robin Getz
- move the CONFIG_KGDB into one block, for easier reading - remove printk from printk_address, and pass around buffers. Also print out the labels when decoding CPLB errors, so you know exactly where the error was. - Do not use fixed addresses, becuase people do not know where they come from. - Turn the printing level down on the dump, so if you don't want, only the signal prints out - just like on other archs. If a kernel/interrupt crashes, it should dump everything all the time Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: Apply Bluetchnix vendor patch provided by Harald KrapfenbauerMichael Hennerich
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: fix bug BlueTechnix CM-BF537 board config uses wrong IRQ for ↵Michael Hennerich
net2272 driver Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: fix bug: kernel prints out error message twiceRobin Getz
This fixes two things: - stop calling write_lock_irq/write_unlock_irq which can turn modify irq levels - don't calling mmput when handing exceptions - since this might_sleep, which does a rti, and leaves us in kernel space (irq15, rather than irq5). Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: add NFC driver support in BF527-EZKIT boardMichael Hennerich
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-29Blackfin arch: Added support for HV Sistemas H8606 boardJavier Herrero
Signed-off-by: Javier Herrero <jherrero@hvsistemas.es> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-10-24blackfin: fix sg falloutAdrian Bunk
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
2007-10-22Merge branch 'for-linus' of ↵Linus Torvalds
master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6 * 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: Blackfin arch: use KBUILD_CFLAGS and KBUILD_AFLAGS in Makefile Blackfin arch: Javier Herrer writes: fix building when icache and dcache is disabled
2007-10-22Update arch/ to use sg helpersJens Axboe
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-22Blackfin arch: use KBUILD_CFLAGS and KBUILD_AFLAGS in MakefileBryan Wu
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 22:22:36 +0000