| Age | Commit message (Collapse) | Author |
|---|
|
Not sure how it slipped by, but here's a trivial typo fix for powernow.
Signed-off-by: Chris Wright <chrisw@osdl.org>
[ It's "nurter" backwards.. Maybe we have a hillbilly The Shining fan? ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
AMD recently discovered that on some hardware, there is a race condition
possible when a C-state change request goes onto the bus at the same
time as a P-state change request.
Both requests happen, but the southbridge hardware only acknowledges the
C-state change. The PowerNow! driver is then stuck in a loop, waiting
for the P-state change acknowledgement. The driver eventually times
out, but can no longer perform P-state changes.
It turns out the solution is to resend the P-state change, which the
southbridge will acknowledge normally.
Thanks to Johannes Winkelmann for reporting this and testing the fix.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Need to use long long, not long when RMWing a MSR. I think
it's harmless right now, but still should be better fixed
if AMD adds any bits in the upper 32bit of HWCR.
Bug was introduced with the TLB flush filter fix for i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This fixes the setup of the alignment of the signal frame, so that all
signal handlers are run with a properly aligned stack frame.
The current code "over-aligns" the stack pointer so that the stack frame
is effectively always mis-aligned by 4 bytes. But what we really want
is that on function entry ((sp + 4) & 15) == 0, which matches what would
happen if the stack were aligned before a "call" instruction.
Signed-off-by: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I need the following patch to compile -git8 here, otherwise these
files fail to compile (asm/hw_irq.h needs definitions from
linux/irq.h and that file provides the required include ordering).
I did not do a full audit, though there looks to be many other
places that should get the same treatment, if this is the right
way to do it.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I checked with AMD and they requested to only disable it for family 15.
Also disable it for i386 too. And some style fixes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Most of these guys are simply not needed (pulled by other stuff
via asm-i386/hardirq.h). One that is not entirely useless is hilarious -
arch/i386/oprofile/nmi_timer_int.c includes linux/irq.h... as a way to
get linux/errno.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Several implementations were essentialy a common piece of C code using
the cmpxchg() macro. Put the implementation in one spot that everyone
can share, and convert sparc64 over to using this.
Alpha is the lone arch-specific implementation, which codes up a
special fast path for the common case in order to avoid GP reloading
which a pure C version would require.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 66759a01adbfe8828dd063e32cf5ed3f46696181 introduced the fix for
time ticking too fast on some boards by disabling one of the doubly
connected timer pins on ATI boards.
However, it ends up being _much_ too broad a brush, and that just makes
some other ATI boards not work at all since they now have no timer
source.
So disable the automatic ATI southbridge detection, and just rely on
people who see this problem disabling it by hand with the option
"disable_timer_pin_1" on the kernel command line.
Maybe somebody can figure out the proper tests at a later date.
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
disable_timer_pin_1 needs IO-APIC, not just local APIC.
Signed-off-by: Cal Peake <cp@absolutedigital.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Masked FPU exceptions should obviously not happen in the first place,
but if they do, ignoring them seems to be the right thing to do.
Although there is no documentation available for Cyrix MII, I did find
erratum F-7 for Winchip C6, "FPU instruction may result in spurious
exception under certain conditions" which seems to indicate that this
can happen.
That would also explain the behaviour Ondrej Zary reported on the MII.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Replace the custom is_digit() macro with isdigit() from <linux/ctype.h>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Use the add_taint() interface for setting tainted bit flags instead of
doing it manually.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
ACPI earlyquirks needs to honor the proper config variables, and include
the right header file.
(Fixes commit 66759a01adbfe8828dd063e32cf5ed3f46696181)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Xpress chipsets
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Since this is shared code I had to implement it for i386 too
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Now that Greg implemented MCFG/_SEG support this shouldn't be needed
anymore
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
processing
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Inside the linker script, insert the code for DWARF debug info sections. This
may help GDB'ing a Uml binary. Actually, it seems that ld is able to guess
what I added correctly, but normal linker scripts include this section so it
should be correct anyway adding it.
On request by Sam Ravnborg <sam@ravnborg.org>, I've added it to
asm-generic/vmlinux.lds.s. I've also moved there the stabs debug section,
used the new macro in i386 linker script and added DWARF debug section to
that.
In the truth, I've not been able to verify the difference in GDB behaviour
after this change (I've seen large improvements with another patch). This
may depend on my binutils version, older one may have worse defaults.
However, this section is present in normal linker script, so add it at
least for the sake of cleanness.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
get_cpu_vendor() no longer has any users in other files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove S4BIOS support. It is pretty useless, and only ever worked for _me_
once. (I do not think anyone else ever tried it). It was in feature-removal
for a long time, and it should have been removed before.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Replace schedule_timeout() with msleep() to guarantee the task delays as
expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
This fixes the problem with "Averatec 6240 pcmcia_socket0: unable to
apply power", which was due to the CardBus IOMEM register region being
allocated at an address that was actually inside the RAM window that had
been reserved for video frame-buffers in an UMA setup.
The BIOS _should_ have marked that region reserved in the e820 memory
descriptor tables, but did not.
It is fixed by rounding up the default starting address of PCI memory
allocations, so that we leave a bigger gap after the final known memory
location. The amount of rounding depends on how big the unused memory
gap is that we can allocate IOMEM from.
Based on example code by Linus.
Acked-by: Greg KH <greg@kroah.com>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
For the i386, code is already present in video.S that gets the EDID from the
video BIOS. Make this visible so drivers can also use this data as fallback
when i2c does not work.
To ensure that the EDID block is returned for the primary graphics adapter
only, by check if the IORESOURCE_ROM_SHADOW flag is set.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add rudimentary support by manipulating the VGA registers. However, not
all vesa modes are VGA compatible, so VGA compatiblity is checked first.
Only 2 levels are supported, powerup and powerdown.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This is the same issue as ppc64 before, when returning to userland we
shouldn't re-compute the seccomp check or the task could be killed during
sigreturn when orig_eax is overwritten by the sigreturn syscall. This was
found by Roland.
This was harmless from a security standpoint, but some i686 users reported
failures with auditing enabled system wide (some distro surprisingly makes
it the default) and I reproduced it too by keeping the whole workload under
strace -f.
Patch is tested and works for me under strace -f.
nobody@athlon:~/cpushare> strace -o /tmp/o -f python seccomp_test.py
make: Nothing to be done for `seccomp_test'.
Starting computing some malicious bytecode
init
load
start
stop
receive_data failure
kill
exit_code 0 signal 9
The malicious bytecode has been killed successfully by seccomp
Starting computing some safe bytecode
init
load
start
stop
174 counts
kill
exit_code 0 signal 0
The seccomp_test.py completed successfully, thank you for testing.
(akpm: collaterally cleaned up a bit of do_syscall_trace() too)
Signed-off-by: Andrea Arcangeli <andrea@cpushare.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove the weird and apparently unnecessary logic in MP_processor_info() which
assumes that the BSP is the first one to run MP_processor_info(). On one of
my boxes that isn't true and cpu_possible_map gets the wrong value.
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The legacy PIC's name is "i8259".
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Building asm-offsets.h has been moved to a seperate Kbuild file
located in the top-level directory. This allow us to share the
functionality across the architectures.
The old rules in architecture specific Makefiles will die
in subsequent patches.
Furhtermore the usual kbuild dependency tracking is now used
when deciding to rebuild asm-offsets.s. So we no longer risk
to fail a rebuild caused by asm-offsets.c dependencies being touched.
With this common rule-set we now force the same name across
all architectures. Following patches will fix the rest.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
|
|
Convert i386/pci to use io_remap_pfn_range instead of remap_pfn_range.
This is good for Xen which reuses i386/pci/i386.c for domain 0 code.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
Sanitized and fixed floppy dependencies: split the messy dependencies for
BLK_DEV_FD by introducing a new symbol (ARCH_MAY_HAVE_PC_FDC), making
BLK_DEV_FD depend on that one and taking declarations of ARCH_MAY_HAVE_PC_FDC
to arch/*/Kconfig. While we are at it, fixed several obvious cases when
BLK_DEV_FD should have been excluded (architectures lacking asm/floppy.h
are *not* going to have floppy.c compile, let alone work).
If you can come up with better name for that ("this architecture might
have working PC-compatible floppy disk controller"), you are more than
welcome - just s/ARCH_MAY_HAVE_PC_FDC/your_prefered_name/g in the patch
below...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch fixes a race condition where in system used to hang or sometime
crash within minutes when kprobes are inserted on ISR routine and a task
routine.
The fix has been stress tested on i386, ia64, pp64 and on x86_64. To
reproduce the problem insert kprobes on schedule() and do_IRQ() functions
and you should see hang or system crash.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch fixes a bug in kprobes's handling of a corner case on i386 and
x86_64. On an SMP system, if one CPU unregisters a kprobe just after
another CPU hits that probepoint, kprobe_handler() on the latter CPU sees
that the kprobe has been unregistered, and attempts to let the CPU continue
as if the probepoint hadn't been hit. The bug is that on i386 and x86_64,
we were neglecting to set the IP back to the beginning of the probed
instruction. This could cause an oops or crash.
This bug doesn't exist on ppc64 and ia64, where a breakpoint instruction
leaves the IP pointing to the beginning of the instruction. I don't know
about sparc64. (Dave, could you please advise?)
This fix has been tested on i386 and x86_64 SMP systems. To reproduce the
problem, set one CPU to work registering and unregistering a kprobe
repeatedly, and another CPU pounding the probepoint in a tight loop.
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch contains the i386 architecture specific changes to prevent the
possible race conditions.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Background:
1) dmi_check_system() returns the count of the number of
matches. Zero thus means no matches.
2) A match callback can return nonzero to stop the match
checking.
Bug: The count is incremented after we check for the nonzero return value,
so it does not reflect the actual count. We could say this is intended,
for some dumb reason, except that it means that a match on the first check
returns zero--no matches--if the callback returns nonzero.
Attached patch implements the count before calling the callback and thus
before potentially short-circuiting.
Signed-off-by: Robert Love <rml@novell.com>
Cc: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds onboard devices and IPMI BMC discovery into DMI scan code.
Drivers can use dmi_find_device() function to search for devices by type and
name.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch changes dmi_string() function to allocate string copy by itself, to
avoid code duplication in the next patch.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
DMI debugging code is unused for ages. This patch removes it.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
After elimination of central DMI blacklist dmi_scan_machine() function became
a wrapper for dmi_iterate(). This patch moves some code around to kill
unneeded function.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch cleans up a commonly repeated set of changes to the NTP state
variables by adding two helper inline functions:
ntp_clear(): Clears the ntp state variables
ntp_synced(): Returns 1 if the system is synced with a time server.
This was compile tested for alpha, arm, i386, x86-64, ppc64, s390, sparc,
sparc64.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Mark variables which are usually accessed for reads with __readmostly.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The second arg of do_timer_interrupt() is not used in the functions, and
all callers pass NULL.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Paul Mundt <lethal@Linux-SH.ORG>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The i386 OProfile code has a function named nmi_exit(), which collides with
the nmi_exit() macro in linux/hardirq.h. At the moment, we get away with
it, because hardirq.h isn't included in the oprofile code. I hit this as a
bug when working with a patch which (indirectly) adds a #include of
hardirq.h to oprofile.
Regardless, the name collision is probably not a good idea, so this patch
fixes it, renaming the oprofile function to op_nmi_exit(). It also renames
the nmi_init() and nmi_timer_init() functions similarly, for consistency.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
