| Age | Commit message (Collapse) | Author |
|---|
|
Spelling and apostrophe fixes in arch/ia64/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
When called to do a transfer that has a start offset within the cache
line which is uneven between source and destination and a length which
terminates the source of the copy exactly on a cache line, one extra
line gets copied into a temporary buffer. This is normally not an issue
since the buffer is a kernel buffer and only the requested information
gets copied into the user buffer.
The problem arises when the source ends at the very last physical page
of memory. That last cache line does not exist and results in the SHUB
chip raising an MCA.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The GFP_DMA option usually does nothing on SN2 since all of memory is in thei
DMA zone and the BTE has always been capable of addressing all of memory.
So there is no need to get memory from a restricted range of memory (which
is what GFP_DMA is for).
Remove useless __GFP_DMA option.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
After converting the cpu physical address to shub2 physical
addressing, the address was run through TO_PHYS() which
clobbered a high node offset bit causing the BTE to fail
on shub2 nodes with large memory. This fix corrects
that problem.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The nasid_index was not being incremented if the
pointer was null, causing an infinite loop.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
bte_copy() calls calls get_nasid(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead.
It is OK if we migrate off node.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
bte_copy() calls calls smp_processor_id(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead
because we are just using it to pick a BTE interface and are not
tied to a specific cpu.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Add a few missing calls to "hint @pause".
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Change the BTE driver so that it works for both shub1 and
shub2. Most of the changes are related to the number of cores
that use the BTE engine, to the MMR addresses of various
shub registers, and to using the correct processor or network
physical address.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
patch 1:
Add new MMR definitions.
Modify BTE initialiation.
Modify BTE copy.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
