aboutsummaryrefslogtreecommitdiff
path: root/arch/powerpc/Kconfig
AgeCommit message (Collapse)Author
2007-02-16[POWERPC] Add PMI driver for cell bladeChristian Krafft
This adds driver code for the PMI device found in future IBM products. PMI stands for "Platform Management Interrupt" and is a way to communicate with the BMC (Baseboard Management Controller). It provides bidirectional communication with a low latency. Signed-off-by: Christian Krafft <krafft@de.ibm.com> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Acked-by: Heiko J Schick <schickhj@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-13[POWERPC] spufs: remove need for struct page for SPEsBenjamin Herrenschmidt
This patch removes the need for struct page for SPE local store and registers from spufs. It also makes the locking much more obvious and no longer relying on the truncate logic black magic for protecting against races between unmap_mapping_range() and new pages faulted in. It does so by switching to a nopfn() handler and using the new vm_insert_pfn() to setup the PTEs itself while holding a lock on the SPE. The nice thing is that this patch actually removes a lot more code than it adds :-) Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-11[PATCH] Set CONFIG_ZONE_DMA for arches with GENERIC_ISA_DMAChristoph Lameter
As Andi pointed out: CONFIG_GENERIC_ISA_DMA only disables the ISA DMA channel management. Other functionality may still expect GFP_DMA to provide memory below 16M. So we need to make sure that CONFIG_ZONE_DMA is set independent of CONFIG_GENERIC_ISA_DMA. Undo the modifications to mm/Kconfig where we made ZONE_DMA dependent on GENERIC_ISA_DMA and set theses explicitly in each arches Kconfig. Reviews must occur for each arch in order to determine if ZONE_DMA can be switched off. It can only be switched off if we know that all devices supported by a platform are capable of performing DMA transfers to all of memory (Some arches already support this: uml, avr32, sh sh64, parisc and IA64/Altix). In order to switch ZONE_DMA off conditionally, one would have to establish a scheme by which one can assure that no drivers are enabled that are only capable of doing I/O to a part of memory, or one needs to provide an alternate means of performing an allocation from a specific range of memory (like provided by alloc_pages_range()) and insure that all drivers use that call. In that case the arches alloc_dma_coherent() may need to be modified to call alloc_pages_range() instead of relying on GFP_DMA. Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-08Merge master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds
* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (116 commits) [POWERPC] Add export of vgacon_remap_base [POWERPC] Remove bogus comment about page_is_ram [POWERPC] windfarm: don't die on suspend thread signal [POWERPC] Fix comment in kernel/irq.c [POWERPC] ppc: Fix booke watchdog initialization [POWERPC] PPC: Use ARRAY_SIZE macro when appropriate [POWERPC] Use ARRAY_SIZE macro when appropriate [POWERPC] Fix ppc64's writing to struct file_operations [POWERPC] ppc: use syslog macro for the printk log level [POWERPC] ppc: cs4218_tdm remove extra brace [POWERPC] Add mpc52xx/lite5200 PCI support [POWERPC] Only use H_BULK_REMOVE if the firmware supports it [POWERPC] Fixup error handling when emulating a floating point instruction [POWERPC] Enable interrupts if we are doing fp math emulation [POWERPC] Added kprobes support to ppc32 [POWERPC] Make pSeries use the H_BULK_REMOVE hypervisor call [POWERPC] Clear RI bit in MSR before restoring r13 when returning to userspace [POWERPC] Fix performance monitor exception [POWERPC] Compile fixes for arch/powerpc dcr code [POWERPC] Maple: use mmio nvram ...
2007-02-08[POWERPC] Add mpc52xx/lite5200 PCI supportGrant Likely
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-07USB: ps3 ohci bus glueGeoff Levand
USB OHCI driver bus glue for the PS3 game console. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07USB: ps3 ehci bus glueGeoff Levand
USB EHCI driver bus glue for the PS3 game console. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-06[POWERPC] Added kprobes support to ppc32Kumar Gala
Added kprobes to ppc32 platforms that have use single_step_exception. This excludes 4xx and anything Book-E since their debug mechanisms for single stepping are completely different. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-02-07Merge branch 'linux-2.6'Paul Mackerras
2007-02-07[POWERPC] Maple: use mmio nvramNathan Lynch
Some systems supported by the maple platform (e.g. JS2x blades running SLOF) are able to use the mmio_nvram backend for reading and writing nvram. This is an improvement over the current situation -- no nvram access from userspace at all. Select MMIO_NVRAM for the maple platform. Initialize the mmio_nvram backend from maple setup code. Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-07[POWERPC] pasemi: iommu supportOlof Johansson
I/O TLB support for PA6T-1682M. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-07[POWERPC] Celleb: basic supportIshizaki Kou
This patch adds base support for Celleb platform. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-07[POWERPC] 8xx: generic 8xx code arch/powerpc portVitaly Bordug
Including support for non-coherent cache, some mm-related things + relevant field in Kconfig and Makefiles. Also included rheap.o compilation if 8xx is defined. Non-coherent mapping were refined and renamed according to Cristoph Hellwig. Orphaned functions were cleaned up. [Also removed arch/ppc/kernel/dma-mapping.c, because otherwise compiling with ARCH=ppc for a non DMA-cache-coherent platform ends up with two copies of __dma_alloc_coherent etc. -- paulus.] Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-01-28Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] Fix sys_pciconfig_iobase bus matching [POWERPC] PS3: add not complete comment to kconfig [POWERPC] ps3_free_io_irq: Fix inverted error check [POWERPC] PS3: Fix uniprocessor kernel build
2007-01-28[POWERPC] PS3: add not complete comment to kconfigGeoff Levand
Add a comment to the PS3 config option to inform users that the current implementation is not yet complete. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-01-26Fix Maple PATA IRQ assignment.David Woodhouse
On the Maple board, the AMD8111 IDE is in legacy mode... except that it appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by the architecture's "pci_get_legacy_ide_irq()" function, but in libata we just hard-code the numbers 14 and 15. This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as appropriate, having added a pci_dev argument to the ATA_{PRIM,SECOND}ARY_IRQ macros. There's probably a better way to do this -- especially if we observe that the _only_ case in which this seemingly-generic "pci_get_legacy_ide_irq()" function returns anything other than 14 and 15 for primary and secondary respectively is the case of the AMD8111 on the Maple board -- couldn't we handle that with a special case in the pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into native mode during early boot and assign resources properly? Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-26[POWERPC] 83xx: Fix Kconfig to only enable FP math emulation for the MPC832xKumar Gala
Updated MATH_EMULATION depends to be on PPC_MPC832x instead of PPC_83xx. Only the the MPC832x has no floating point unit in the core. Updated the other 83xx defconfigs that got math emulation turned on incorrectly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-01-09[POWERPC] disable PReP and EFIKA during make oldconfigOlaf Hering
New boards should not be enabled per default. Disable EFIKA and PReP per default. Anyone who really needes the new code can enable it during make oldconfig. Signed-off-by: Olaf Hering <olaf@aepfle.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (36 commits) [POWERPC] Generic BUG for powerpc [PPC] Fix compile failure do to introduction of PHY_POLL [POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set [POWERPC] Remove old dcr.S [POWERPC] Fix SPU coredump code for max_fdset removal [POWERPC] Fix irq routing on some 32-bit PowerMacs [POWERPC] ps3: Add vuart support [POWERPC] Support ibm,dynamic-reconfiguration-memory nodes [POWERPC] dont allow pSeries_probe to succeed without initialising MMU [POWERPC] micro optimise pSeries_probe [POWERPC] Add SPURR SPR to sysfs [POWERPC] Add DSCR SPR to sysfs [POWERPC] Fix 440SPe CPU table entry [POWERPC] Add support for FP emulation for the e300c2 core [POWERPC] of_device_register: propagate device_create_file return code [POWERPC] Fix mmap of PCI resource with hack for X [POWERPC] iSeries: head_64.o needs to depend on lparmap.s [POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group [POWERPC] Remove QE header files from lite5200.c [POWERPC] of_platform_make_bus_id(): make `magic' int ...
2006-12-11[POWERPC] Generic BUG for powerpcJeremy Fitzhardinge
This makes powerpc use the generic BUG machinery. The biggest reports the function name, since it is redundant with kallsyms, and not needed in general. There is an overall reduction of code, since module_32/64 duplicated several functions. Unfortunately there's no way to tell gcc that BUG won't return, so the BUG macro includes a goto loop. This will generate a real jmp instruction, which is never used. [akpm@osdl.org: build fix] [paulus@samba.org: remove infinite loop in BUG_ON] Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Andi Kleen <ak@muc.de> Cc: Hugh Dickens <hugh@veritas.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-11Merge branch 'for_paulus' of ↵Paul Mackerras
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
2006-12-08[PATCH] LOG2: Provide ilog2() fallbacks for powerpcDavid Howells
Provide ilog2() fallbacks for powerpc for 32-bit numbers and 64-bit numbers on ppc64. Signed-off-by: David Howells <dhowells@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08[PATCH] LOG2: Implement a general integer log2 facility in the kernelDavid Howells
This facility provides three entry points: ilog2() Log base 2 of unsigned long ilog2_u32() Log base 2 of u32 ilog2_u64() Log base 2 of u64 These facilities can either be used inside functions on dynamic data: int do_something(long q) { ...; y = ilog2(x) ...; } Or can be used to statically initialise global variables with constant values: unsigned n = ilog2(27); When performing static initialisation, the compiler will report "error: initializer element is not constant" if asked to take a log of zero or of something not reducible to a constant. They treat negative numbers as unsigned. When not dealing with a constant, they fall back to using fls() which permits them to use arch-specific log calculation instructions - such as BSR on x86/x86_64 or SCAN on FRV - if available. [akpm@osdl.org: MMC fix] Signed-off-by: David Howells <dhowells@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: David Howells <dhowells@redhat.com> Cc: Wojtek Kaniewski <wojtekka@toxygen.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08[POWERPC] Add support for FP emulation for the e300c2 coreKim Phillips
The e300c2 has no FPU. Its MSR[FP] is grounded to zero. If an attempt is made to execute a floating point instruction (including floating-point load, store, or move instructions), the e300c2 takes a floating-point unavailable interrupt. This patch adds support for FP emulation on the e300c2 by declaring a new CPU_FTR_FP_TAKES_FPUNAVAIL, where FP unavail interrupts are intercepted and redirected to the ProgramCheck exception path for correct emulation handling. (If we run out of CPU_FTR bits we could look to reclaim this bit by adding support to test the cpu_user_features for PPC_FEATURE_HAS_FPU instead) It adds a nop to the exception path for 32-bit processors with a FPU. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2006-12-08[POWERPC] maple: Select PPC_RTASNathan Lynch
Some systems supported by the maple platform have RTAS; make PPC_MAPLE select PPC_RTAS. Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-05[POWERPC] Remove obsolete PPC_52xx and update CLASSIC32 commentGrant Likely
The support for the 52xx-based systems is now included under CONFIG_CLASSIC32, since the 52xx chips have a 603e-based core. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] Add lite5200 board support to arch/powerpcGrant Likely
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] Put mpc52xx support file in platforms/52xxGrant Likely
platforms/embedded6xx is probably going away, and 52xx boards need some extra support the 52xx interrupt controller and DMA engine anyway. It makes sense to group all the 52xx bits into a single path. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] iSeries: allow CONFIG_CMDLINEStephen Rothwell
It doesn't hurt to have this enabled on legacy iSeries and will mean it is available for a combined build. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] ps3: multiplatform build fixesArnd Bergmann
A few code paths need to check whether or not they are running on the PS3's LV1 hypervisor before making hcalls. This introduces a new firmware feature bit for this, FW_FEATURE_PS3_LV1. Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES, FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time, which is a bug. The same problem can also happen for (PPC_ISERIES && !PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I introduce a new CONFIG_PPC_NATIVE option that is set when at least one platform is selected that can run without a hypervisor and then turns the firmware feature check into a run-time option. The new cell oprofile support that was recently merged does not work on hypervisor based platforms like the PS3, therefore make it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change if we get oprofile support for PS3. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
2006-12-04[POWERPC] ps3: add support for ps3 platformGeoff Levand
Adds the core platform support for the PS3 game console and other devices using the PS3 hypervisor. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
2006-12-04[POWERPC] Remove ioremap64 and fixup_bigphys_addrBenjamin Herrenschmidt
In order to suppose platforms with devices above 4Gb on 32 bits platforms with a >32 bits physical address space, we used to have a special ioremap64 along with a fixup routine fixup_bigphys_addr. This shouldn't be necessary anymore as struct resource now supports 64 bits addresses even on 32 bits archs. This patch enables that option when CONFIG_PHYS_64BIT is set and removes ioremap64 and fixup_bigphys_addr. This is a preliminary work for the upcoming merge of 32 and 64 bits io.h Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] Cell "Spider" MMIO workaroundsBenjamin Herrenschmidt
This patch implements a workaround for a Spider PCI host bridge bug where it doesn't enforce some of the PCI ordering rules unless some manual manipulation of a special register is done. In order to be fully compliant with the PCI spec, I do this on every MMIO read operation. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] Allow hooking of PCI MMIO & PIO accessors on 64 bitsBenjamin Herrenschmidt
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO and PIO) and provides a generic way for other platforms to do so (we have need to do that for various other platforms). While reworking the IO ops, I ended up doing some spring cleaning in io.h and eeh.h which I might want to split into 2 or 3 patches (among others, eeh.h had a lot of useless stuff in it). A side effect is that EEH for PIO should work now (it used to pass IO ports down to the eeh address check functions which is bogus). Also, new are MMIO "repeat" ops, which other archs like ARM already had, and that we have too now: readsb, readsw, readsl, writesb, writesw, writesl. In the long run, I might also make EEH use the hooks instead of wrapping at the toplevel, which would make things even cleaner and relegate EEH completely in platforms/iseries, but we have to measure the performance impact there (though it's really only on MMIO reads) Since I also need to hook on ioremap, I shuffled the functions a bit there. I introduced ioremap_flags() to use by drivers who want to pass explicit flags to ioremap (and it can be hooked). The old __ioremap() is still there as a low level and cannot be hooked, thus drivers who use it should migrate unless they know they want the low level version. The patch "arch provides generic iomap missing accessors" (should be number 4 in this series) is a pre-requisite to provide full iomap API support with this patch. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] Generic OF platform driver for PCI host bridges.Benjamin Herrenschmidt
When enabled in Kconfig, it will pick up any of_platform_device matching it's match list (currently type "pci", "pcix", "pcie", or "ht" and setup a PHB for it. Platform must provide a ppc_md.pci_setup_phb() for it to work (for doing the necessary initialisations specific to a given PHB like setting up the config space ops). It's currently only available on 64 bits as the 32 bits PCI code can't quite cope with it in it's current form. I will fix that later. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] Native cell support for MPIC in southbridgeBenjamin Herrenschmidt
Add support for southbridges using the MPIC interrupt controller to the native cell platforms. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04[POWERPC] Generic DCR infrastructureBenjamin Herrenschmidt
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that can be used by drivers to transparently address either native DCRs or memory mapped DCRs. The implementation for memory mapped DCRs is done after the binding being currently worked on for SLOF and the Axon chipset. This patch enables it for the cell native platform Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04Merge branch 'linux-2.6' into for-linusPaul Mackerras
2006-11-30Fix misc Kconfig typosMatt LaPlante
Fix various Kconfig typos. Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-11-13[PATCH] Add Efika platform supportNicolas DET
Add Efika (http://www.bplan-gmbh.de/efika_spec_en.html) platform support for arch/powerpc. Signed-off-by: Nicolas DET <nd@bplan-gmbh.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-10[POWERPC] cell: set ARCH_SPARSEMEM_DEFAULT in KconfigGeoff Levand
The current cell processor support needs sparsemem, so set it as the default memory model. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-21[PATCH] Reintroduce NODES_SPAN_OTHER_NODES for powerpcAndy Whitcroft
Reintroduce NODES_SPAN_OTHER_NODES for powerpc Revert "[PATCH] Remove SPAN_OTHER_NODES config definition" This reverts commit f62859bb6871c5e4a8e591c60befc8caaf54db8c. Revert "[PATCH] mm: remove arch independent NODES_SPAN_OTHER_NODES" This reverts commit a94b3ab7eab4edcc9b2cb474b188f774c331adf7. Also update the comments to indicate that this is still required and where its used. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Mike Kravetz <kravetz@us.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-16[POWERPC] Remove todc code from ARCH=powerpcDavid Gibson
Apparently we've copied the todc drivers, for various RTCs used in embedded machines from ARCH=ppc to ARCH=powerpc, despite the fact that it's never used in the latter. This patch removes it. If we ever need these drivers (which we probably shouldn't now the RTC class stuff is in), we can transfer them one by one from ARCH=ppc, removing from the hideous abomination which is the todc "infrastructure". Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (25 commits) [POWERPC] Add support for the mpc832x mds board [POWERPC] Add initial support for the e300c2 core [POWERPC] Add MPC8360EMDS default dts file [POWERPC] Add MPC8360EMDS board support [POWERPC] Add QUICC Engine (QE) infrastructure [POWERPC] Add QE device tree node definition [POWERPC] Don't try to just continue if xmon has no input device [POWERPC] Fix a printk in pseries_mpic_init_IRQ [POWERPC] Get default baud rate in udbg_scc [POWERPC] Fix zImage.coff on oldworld PowerMac [POWERPC] Fix xmon=off and cleanup xmon initialisation [POWERPC] Cleanup include/asm-powerpc/xmon.h [POWERPC] Update swim3 printk after blkdev.h change [POWERPC] Cell interrupt rework POWERPC: mpc82xx merge: board-specific/platform stuff(resend) POWERPC: 8272ads merge to powerpc: common stuff POWERPC: Added devicetree for mpc8272ads board [POWERPC] iSeries has no legacy I/O [POWERPC] implement BEGIN/END_FW_FTR_SECTION [POWERPC] iSeries does not need pcibios_fixup_resources ...
2006-10-04[POWERPC] Add QUICC Engine (QE) infrastructureLi Yang
Add QUICC Engine (QE) configuration, header files, and QE management and library code that are used by QE devices drivers. Includes Leo's modifications up to, and including, the platform_device to of_device adaptation: "The series of patches add generic QE infrastructure called qe_lib, and MPC8360EMDS board support. Qe_lib is used by QE device drivers such as ucc_geth driver. This version updates QE interrupt controller to use new irq mapping mechanism, addresses all the comments received with last submission and includes some style fixes. v2: Change to use device tree for BCSR and MURAM; Remove I/O port interrupt handling code as it is not generic enough. v3: Address comments from Kumar; Update definition of several device tree nodes; Copyright style change." In addition, the following changes have been made: o removed typedefs o uint -> u32 conversions o removed following defines: QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER, BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET because they hid sizeof/in_be32/out_be32 operations from the reader. o fixed qe_snums_init() serial num assignment to use a const array o made CONFIG_UCC_FAST select UCC_SLOW o reduced NR_QE_IC_INTS from 128 to 64 o remove _IO_BASE, etc. defines (not used) o removed irrelevant comments, added others to resemble removed BD_ defines o realigned struct definitions in headers o various other style fixes including things like pinMask -> pin_mask o fixed a ton of whitespace issues o marked ioregs as __be32/__be16 o removed platform_device code and redundant get_qe_base() o removed redundant comments o added cpu_relax() to qe_reset o uncasted all get_property() assignments o eliminated unneeded casts o eliminated immrbar_phys_to_virt (not used) Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Shlomi Gridish <gridish@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-04Merge branch 'upstream' of ↵Paul Mackerras
git://git.kernel.org/pub/scm/linux/kernel/git/vitb/linux-2.6-PQ
2006-10-04Merge branch 'master' of git://oak/home/sfr/kernels/iseries/workPaul Mackerras
2006-10-03Attack of "the the"s in archMatt LaPlante
The patch below corrects multiple occurances of "the the" typos across several files, both in source comments and KConfig files. There is no actual code changed, only text. Note this only affects the /arch directory, and I believe I could find many more elsewhere. :) Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03POWERPC: 8272ads merge to powerpc: common stuffVitaly Bordug
This has modules of common directories related to the mpc8272ADS board, mainly common cpm2 changes and fsl_soc.c portions related to the bitbang MDIO and other mechanisms specific for this family. Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
2006-10-03[POWERPC] Allow combined iSeries and MULTIPLATFORM buildStephen Rothwell
This will build with ISERIES, PSERIES and PMAC64 selected, but will only boot on iSeries so far. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>