| Age | Commit message (Collapse) | Author |
|---|
|
The wrapper script is missing the bits needed for building generic
simpleImage targets (targets which don't depend on any particular
firmware interface and retrieve all their data from the device tree).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The following changes add processing to initialize the Xilinx 16550 UART
in the boot wrapper for Virtex targets without firmware. Normally the
boot wrapper assumes that the serial port has already been initialized by
firmware.
The wrapper was also modified to add the 440 build.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Currently we set the start of the .text section to be 4Mb for pSeries.
In situations where the zImage is > 8Mb we'll fail to boot (due to
overlapping with OF). Move .text in a zImage from 4MB to 64MB
(well past OF).
We still will not be able to load large zImage unless we also move OF,
to that end, add a note to the zImage ELF to move OF to 32Mb. If this
is the very first kernel booted then we'll need to move OF manually by
setting real-base.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Now that we properly set the physical address in the program header of the
vmlinux ELF we can extract it to properly set the load and entry point for
u-boot uImages. Before we always hard coded the load & entry point to 0.
However there are situations that the kernel may be built with a non-zero
physical address.
We use objdump to extract the PHDR. We assume that there is only one
PHDR in the vmlinux of type LOAD.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Improve the debugging support of the PS3 bootwraper code:
o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
allow for more debugging code in the overlay.
o Use the dot symbol to set the size of __system_reset_overlay. The
assembler will then emit an error if the overlay code is too big.
o Remove some unused instructions.
o Update the text describing the PS3 bootwrapper overlay.
o Add a check for null pointer writes.
o Change hcall return value from s64.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards. I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig. There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This fixes the following bug:
http://ozlabs.org/pipermail/linuxppc-dev/2008-February/051979.html
Separate defconfigs are no longer needed now that CONFIG_DEVICE_TREE is gone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Currently, the kernel uses CONFIG_DEVICE_TREE to wrap a kernel image
with a fdt blob which means for any given configuration only one dts
file can be selected and so support for only one board can be built
This moves the selection of the default .dts file out of the kernel
config and into the bootwrapper makefile. The makefile chooses which
images to build based on the kernel config and the dts source file
name is taken directly from the image name. For example "cuImage.ebony"
will use "ebony.dts" as the device tree source file.
In addition, this patch allows a specific image to be requested from the
command line by adding "cuImage.%" and "treeImage.%" targets to the list
of valid built targets in arch/powerpc/Makefile. This allows the default
dts selection to be overridden.
Another advantage to this change is it allows a single defconfig to be
supplied for all boards using the same chip family and only differing in
the device tree.
Important note: This patch adds two new zImage targets; zImage.dtb.% and
zImage.dtb.initrd.% for zImages with embedded dtb files. Currently
there are 5 platforms which require this: ps3, ep405, mpc885ads, ep88xc,
adder875-redboot and ep8248e. This patch *changes the zImage filenames*
for those platforms. ie. 'zImage.ps3' is now 'zImage.dtb.ps3'.
This new zImage.dtb targets were added so that the .dts file could be
part of the dependancies list for building them.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Brings EP405 support to arch/powerpc. The IRQ routing for the CPLD
comes from a device-tree property, PCI is working to the point where
I can see the video card, USB device, and south bridge.
This should work with both EP405 and EP405PC.
I've not totally figured out how IRQs are wired on this hardware
though, thus at this stage, expect only USB interrupts working,
pretty much the same as what arch/ppc did.
Also, the flash, nvram, rtc and temp control still have to be wired.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This patch alters the kernel makefiles to build dtc from the sources
embedded in the previous patch. It also changes the
arch/powerpc/boot/wrapper script to use the embedded dtc, rather than
expecting a copy of dtc already installed on the system.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
objects
It's possible that the executables which are built as helpers for the
bootwrapper stuff might end up in a different place to the intermediate
object files. Handle that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
If a .dts file is given to the bootwrapper script without a full path
name, look in a sensible place for it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
directory
The bootwrapper script currently generates an 'otheros.bld' file in
addition to the file specified by the -o option, when asked to build a
wrapper for PS3.
It should do that in the same directory as the output, not the directory
where the wrapper objects are kept (which might potentially not be
writable when the script runs).
Arguably, the 'otheros.bld' ought to be created with the filename
specified as the -o argument. But that's a more intrusive change.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx into merge
|
|
The ps3 target produces two images, and the binary one is not the
"primary" image that corresponds to the -o flag; thus, it no longer
uses the generic binary flag.
On platforms which do use the binary flag, it no longer produces a
.bin suffix, so that the output file matches what was passed to the -o flag.
This should fix the zImage ln problems for the ps3 target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add the 'set -e' command to the wrapper script so that if any command
fails then the script will automatically exit
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Allow wrapper script to print verbose progress when the V is set in the
environment.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add support to build the PS3 flash rom image and remove some unneeded
lmb calls.
The PS3's lv1 loader supports loading gzipped binary images from flash
rom to addr zero. The loader enters the image at addr 0x100.
In this implementation a bootwrapper overlay is use to arrange for the
kernel to be loaded to addr zero and to have a suitable bootwrapper
entry at 0x100. To construct the rom image, 0x100 bytes from offset
0x100 in the kernel is copied to the bootwrapper symbol
__system_reset_kernel. The 0x100 bytes at the bootwrapper symbol
__system_reset_overlay is then copied to offset 0x100. At runtime the
bootwrapper program copies the 0x100 bytes at __system_reset_kernel to
addr 0x100.
zImage.ps3 is a wrapped image that contains a flat device tree, an lv1
compatible entry point, and an optional initrd. otheros.bld is the gzip
compresed rom image built from zImage.ps3. otheros.bld is suitable for
programming into the PS3 boot flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Commit 9da82a6dee9db4cd5ae7a74ab4f51afb52b6efb9 inadvertently
removed the platform override for zImage.coff to be generated
with pmaccoff. Rather than add a special makefile rule,
change the platform for which the wrapper platform uses
the special rules.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This adds platform support code for the Ebony (440GP) evaluation
board. This includes both code in arch/powerpc/platforms/44x for
board initialization, and zImage wrapper code to correctly tweak the
flattened device tree based on information from the firmware. The
zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of
uboot which don't support a flattened device tree.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch makes a few small cleanups to the cuboot code.
- It removes the double layered selection of images, via
cuboot-plat-y, instead having the cuboot platforms directly select a
suitable image-y (this changes the name of the final cuboot image from
plain cuImage to cuImage.<platform>).
- Factors out some code in the wrapper that's potentially
useful to platforms other than uboot.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The cuImage target will build a uImage with bootwrapper code and a device
tree. The default device tree and platform file are determined by the
kernel configuration.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Commit a9903811bf8d130a26004f9cb27b66513a267908 missed two uses of the
the .gz suffix in the wrapper script and didn't clean the additonal
possibly cached files.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The --no-gzip option can be passed to the wrapper so that the kernel
image is included uncompressed into the zImage. This is intended for
bootloaders where the zImage itself can be compressed, or where boot time
is considered more important than kernel image size.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch re-organises the way the zImage wrapper code is entered, to
allow more flexibility on platforms with unusual entry conditions.
After this patch, a platform .o file has two options:
1) It can define a _zimage_start, in which case the platform code gets
control from the very beginning of execution. In this case the
platform code is responsible for relocating the zImage if necessary,
clearing the BSS, performing any platform specific initialization, and
finally calling start() to load and enter the kernel.
2) It can define platform_init(). In this case the generic crt0.S
handles initial entry, and calls platform_init() before calling
start(). The signature of platform_init() is changed, however, to
take up to 5 parameters (in r3..r7) as they come from the platform's
initial loader, instead of a fixed set of parameters based on OF's
usage.
When using the generic crt0.S, the platform .o can optionally
supply a custom stack to use, using the BSS_STACK() macro. If this
is not supplied, the crt0.S will assume that the loader has
supplied a usable stack.
In either case, the platform code communicates information to the
generic code (specifically, a PROM pointer for OF systems, and/or an
initrd image address supplied by the bootloader) via a global
structure "loader_info".
In addition the wrapper script is rearranged to ensure that the
platform .o is always linked first. This means that platforms where
the zImage entry point is at a fixed address or offset, rather than
being encoded in the binary header can be supported using option (1).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
When the wrapper script is passed a dts file, it runs 'dtc' to create
a dtb file. This patch deletes that dtb file once its no longer needed.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
More reorganization of the bootwrapper:
- Add dtb section to zImage
- ft_init now called by platform_init
- Pack a flat dt before calling kernel
- Remove size parameter from free
- printf only calls console_ops.write it its not NULL
- Some cleanup
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This puts the knowledge of how to create various sorts of zImage
wrappers into a script called "wrapper" that could be used outside of
the kernel tree. This changes arch/powerpc/boot so it first builds
the files that the wrapper script needs, then runs it to create
whatever flavours of zImage are required.
This version does uImages as well. The zImage names are changed
slightly; zImage.pseries is the one with the PT_NOTE program header
entry added, and zImage.pmac is the one without. If the
zImage.pseries gets made, it will also get hardlinked to zImage;
otherwise, if zImage.pmac is made, it gets hardlinked to zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
