aboutsummaryrefslogtreecommitdiff
path: root/arch/powerpc/boot
AgeCommit message (Collapse)Author
2009-02-06powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boardsAnton Vorontsov
TSEC0 is connected to Vitesse 7385 5-port switch. The switch isn't connected to any mdio bus, the link to the switch is fixed to Full-duplex 1000 Mb/s (no pause). This patch fixes following failure during bootup: mdio@24520:01 not found eth0: Could not attach to PHY IP-Config: Failed to open eth0 Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-06powerpc/83xx: Fix missing #{address,size}-cells in mpc8313erdb.dtsAnton Vorontsov
commit b31a1d8b41513b96e9c7ec2f68c5734cef0b26a4 ("gianfar: Convert gianfar to an of_platform_driver") introduced a child node for the ethernet@25000 controller, but no address and size cells specifiers were added, and that makes dtc unhappy: DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts" Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1) Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520 Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520 Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-28Merge commit 'jwb/jwb-merge' into mergeBenjamin Herrenschmidt
Manual merge of: arch/powerpc/configs/44x/warp_defconfig
2009-01-26powerpc/mpc8313erdb: fix kernel panic because mdio device is not probedLi Yang
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when gianfar driver wants to get the of_platform_device of that mdio. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-20powerpc/85xx: Fix typo in mpc8572ds dtsKumar Gala
The localbus node flash had a minor typo for a read-only property. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-20powerpc/44x: Warp patches for the new NDFC driverSean MacLennan
Convert the Warp platform to use the newly merged NDFC driver - warp.dts changed to work with ndfc - warp-nand.c no longer needed - removed obsolete rev A support from cuboot-warp.c Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-01-20powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt InfoGrant Erickson
Added additional information for type and compatibility strings and interrupt information to the SDRAM0 memory-controller device tree nodes for AMCC PowerPC 405EX[r]-based boards to facilitate binding with the new "ibm,sdram-4xx-ddr2" EDAC memory controller adapter driver. Signed-off-by: Grant Erickson <gerickson@nuovations.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-01-13powerpc/83xx: Make serial ports work on MPC8315E-RDB w/ FSL U-BootsAnton Vorontsov
FSL U-Boots use /soc8315@e0000000 node to search and fixup serial nodes' clock-frequency properties. Though in upstream kernels we use new naming convention -- for IMMR address space dts files specify /immr@e0000000 nodes. This makes FSL U-Boots fail to fixup the clock frequencies, and that leads to serial ports misbehaviour. We can workaround the issue by filling the clock frequency values manually. p.s. For the same reason FSL U-Boots fail to fixup MAC addresses for ethernet nodes, so users should either change the .dts file locally or set MAC address via `ifconfig hw ether' command. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-13Merge commit 'kumar/kumar-next' into nextBenjamin Herrenschmidt
2009-01-12[WATCHDOG] Enable watchdog timer on GE Fanuc's SBC610Martyn Welch
Support for the FPGA based watchdog timer on GE Fanuc's SBC610. This patch enables one of the watchdog timers found on the SBC610. There are two identical watchdog timers at different offsets in the above mentioned boards, however the current driver is only capable of supporting one of them. The watchdog timers are also capable of generating interrupts at a user-configurable threshold, though support for this operation is currently not supported by the driver. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2009-01-08powerpc: Copy bootable images in the default install scriptGrant Likely
This patch makes the default install script (arch/powerpc/boot/install.sh) copy the bootable image files into the install directory. Before this patch only the vmlinux image file was copied. This patch makes the default 'make install' command useful for embedded development when $(INSTALL_PATH) is set in the environment. As a side effect, this patch changes the calling convention of the install.sh script. Instead of a single 5th parameter, the script is now passed a list of all the target images stored in the $(image-y) Makefile variable. This should be backwards compatible with existing install scripts since it just adds additional arguments and does not change existing ones. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-08Merge commit 'origin/master' into nextBenjamin Herrenschmidt
2009-01-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits) wimax/i2400m: add CREDITS and MAINTAINERS entries wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install i2400m: Makefile and Kconfig i2400m/SDIO: TX and RX path backends i2400m/SDIO: firmware upload backend i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends i2400m/SDIO: header for the SDIO subdriver i2400m/USB: TX and RX path backends i2400m/USB: firmware upload backend i2400m/USB: probe/disconnect, dev init/shutdown and reset backends i2400m/USB: header for the USB bus driver i2400m: debugfs controls i2400m: various functions for device management i2400m: RX and TX data/control paths i2400m: firmware loading and bootrom initialization i2400m: linkage to the networking stack i2400m: Generic probe/disconnect, reset and message passing i2400m: host/device procotol and core driver definitions i2400m: documentation and instructions for usage wimax: Makefile, Kconfig and docbook linkage for the stack ...
2009-01-07USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]Vitaly Bordug
A published errata for ppc440epx states, that when running Linux with both EHCI and OHCI modules loaded, the EHCI module experiences a fatal error when a high-speed device is connected to the USB2.0, and functions normally if OHCI module is not loaded. There used to be recommendation to use only hi-speed or full-speed devices with specific conditions, when respective module was unloaded. Later, it was observed that ohci suspend is enough to keep things going, and it was turned into workaround, as explained below. Quote from original descriprion: The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In USB 2.0 Host controllers, each EHCI controller has one or more companion controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will contain one or more ports. For each port, only one of the controllers is connected at any one time. In the 440EPx, there is only one OHCI companion controller, and only one USB 2.0 Host port. All ports on an USB 2.0 controller default to the companion controller. If you load only an ohci driver, it will have control of the ports and any deviceplugged in will operate, although high speed devices will be forced to operate at full speed. When an ehci driver is loaded, it explicitly takes control of the ports. If there is a device connected, and / or every time there is a new device connected, the ehci driver determines if the device is high speed or not. If it is high speed, the driver retains control of the port. If it is not, the driver explicitly gives the companion controller control of the port. The is a software workaround that uses Initial version of the software workaround was posted to linux-usb-devel: http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html and later available from amcc.com: http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2 The patch below is generally based on the latter, but reworked to powerpc/of_device USB drivers, and uses a few devicetree inquiries to get rid of (some) hardcoded defines. Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org> Signed-off-by: Stefan Roese <sr@denx.de> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07powerpc/85xx: Fix PCIe error interruptsKumar Gala
The PCIe interrupts for 8544ds and 8572ds were incorrect. The 8572 case was found by Liu Yu. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-06trivial: Fix misspelling of "firmware" in powerpc MakefileNick Andrew
Fix misspelling of "firmware" in powerpc Makefile It's spelled "firmware". Signed-off-by: Nick Andrew <nick@nick-andrew.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-01-05Merge commit 'kumar/kumar-next' into nextBenjamin Herrenschmidt
2008-12-30powerpc/86xx: Update 8641hpcn dts file to match latest u-bootBecky Bruce
The newest revision of uboot reworks the memory map for this board to look more like the 85xx boards. Also, some regions which were far larger than the actual hardware have been scaled back to match the board, and the imaginary second flash bank has been removed. Rapidio and PCI are mutually exclusive in the hardware, and they now are occupying the same space in the address map. The Rapidio node is commented out of the .dts since PCI is the common use case. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-30powerpc/83xx: Add USB Host support for MPC8360E-RDK boardsAnton Vorontsov
Simply add the usb node to support USB host on the MPC8360E-RDK boards. Currently U-Boot doesn't fill the clock-frequency property for timer nodes, so for now we have to fill it manually. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-30powerpc/83xx: Add USB Host/Gadget support for MPC8360E-MDS boardsAnton Vorontsov
- Update the device tree per QE USB bindings; - Add timer (FSL GTM) node; - Add gpio-controller node for BCSR13 bank (GPIOs on that bank are used to control the USB transceiver); - Set up other BCSR registers; - Configure the QE Par IO. The work is loosely based on Li Yang's patch[1], which was used to support peripheral mode only. [1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html The s-o-b line of the original patch preserved here. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-28Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits) powerpc/44x: Support 16K/64K base page sizes on 44x powerpc: Force memory size to be a multiple of PAGE_SIZE powerpc/32: Wire up the trampoline code for kdump powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M powerpc/32: Allow __ioremap on RAM addresses for kdump kernel powerpc/32: Setup OF properties for kdump powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs() powerpc: Prepare xmon_save_regs for use with kdump powerpc: Remove default kexec/crash_kernel ops assignments powerpc: Make default kexec/crash_kernel ops implicit powerpc: Setup OF properties for ppc32 kexec powerpc/pseries: Fix cpu hotplug powerpc: Fix KVM build on ppc440 powerpc/cell: add QPACE as a separate Cell platform powerpc/cell: fix build breakage with CONFIG_SPUFS disabled powerpc/mpc5200: fix error paths in PSC UART probe function powerpc/mpc5200: add rts/cts handling in PSC UART driver powerpc/mpc5200: Make PSC UART driver update serial errors counters powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver ... Fix trivial conflict in drivers/char/Makefile as per Paul's directions
2008-12-22powerpc/cell: add QPACE as a separate Cell platformBenjamin Krill
Since the QPACE (Chromodynamics Parallel Computing on the Cell Broadband Engine) platform doesn't use a iommu, doesn't have PCI devices and a MPIC much lesser setup and configurations are needed. So far all devices are detected as OF device. A notifier function is used to set the dma_ops for the of_platform bus. Further this patch splits the PPC_CELL_NATIVE into PPC_CELL_COMMON which are parts that are shared with the QPACE platform and the rest. Signed-off-by: Benjamin Krill <ben@codiert.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2008-12-21powerpc/bootwrapper: Use the child-bus #address-cells to decide which range ↵Scott Wood
entry to use The correct #address-cells was still used for the actual translation, so the impact is only a possibility of choosing the wrong range entry or failing to find any match. Most common cases were not affected. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-12-17Merge branch 'next' of ↵Paul Mackerras
master.kernel.org:/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx into next
2008-12-16gianfar: Convert gianfar to an of_platform_driverAndy Fleming
Does the same for the accompanying MDIO driver, and then modifies the TBI configuration method. The old way used fields in einfo, which no longer exists. The new way is to create an MDIO device-tree node for each instance of gianfar, and create a tbi-handle property to associate ethernet controllers with the TBI PHYs they are connected to. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16Merge branch 'merge' into nextPaul Mackerras
2008-12-15powerpc/85xx: Fix compile issues with mpc8572ds.dtsKumar Gala
Fix the localbus reg & range properties to respect that the top level #address-cells and #size-cells = 2. The original commit (c64ef80b517680f1e228b2ee55e3ce7cd94c7fe0) did not do that. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-11powerpc/4xx: Add L2 cache node to AMCC Canyonlands dts fileStefan Roese
With this patch the L2 cache is enabled on Canyonlands to increase the overall performance. There is a known cache coherency issue with the L2 cache, but this is related to the high bandwidth (HB) PLB segment where the memory address is 0x8.xxxx.xxxx (low bandwidth PLB segment is mapped to 0x0.xxxx.xxxx). Since this HB address is currently unused it is safe to enable the L2 cache. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-12-11powerpc/40x: Add proper BOOTCFLAGS for cuboot-acadiaJosh Boyer
The cuboot-acadia.c wrapper can cause assembler errors on some toolchains due to the lack of the proper BOOTCFLAGS. This adds the proper flags for the file. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-12-04powerpc/4xx: Add support for ISA holes on 4xx PCI/X/EBenjamin Herrenschmidt
This adds support for ISA memory holes on the PCI, PCI-X and PCI-E busses of the 4xx platforms. The patch includes changes to the Bamboo and Canyonlands device-trees to add such a hole, others can be updated separately. The ISA memory hole is an additional outbound window configured in the bridge to generate PCI cycles in the low memory addresses, thus allowing to access things such as the hard-decoded VGA aperture at 0xa0000..0xbffff or other similar things. It's made accessible to userspace via the new legacy_mem file in sysfs for which support was added by a previous patch. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-12-03powerpc/85xx: Create dts for each core in CAMP mode for MPC8572DSHaiying Wang
This patch creates the dts files for each core and splits the devices between the two cores for MPC8572DS. core0 has memory, L2, i2c, dma1, global-util, eth0, eth1, crypto, pci0, pci1. core1 has L2, dma2, eth2, eth3, pci2, msi. MPIC is shared between two cores but each core will protect its interrupts from other core by using "protected-sources" of mpic. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-03powerpc/85xx: Add localbus node in mpc8572ds dts fileHaiying Wang
Also add NOR and NAND flash partitions for mpc8572ds board Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-03powerpc/86xx: Basic GPIO support for GE Fanuc SBC610Martyn Welch
Basic support for the GPIO available on the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D). This patch adds basic support for the GPIO in the devices I/O FPGA, the GPIO functionality is exposed through the AFIX pins on the backplane, unless used by an AFIX card. This code currently does not support switching between totem-pole and open-drain outputs (when used as outputs, GPIOs default to totem-pole). The interrupt capabilites of the GPIO lines is also not currently supported. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-03powerpc/86xx: Add use of Epson RTX-8581 RTC to GE Fanuc SBC610 dtsMartyn Welch
Adding use of newly added Epson RTX-8581 real-time clock driver to GE Fanuc SBC610's dts file and adding driver to default config. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-03powerpc/83xx: Fix MCU support merge issue in mpc8349emitx.dtsAnton Vorontsov
Just found the merge issue in 442746989d92afc125040e0f29b33602ad94da99 ("powerpc/83xx: Add support for MCU microcontroller in .dts files"): the commit adds the MCU controller node into the DMA node, which is wrong because the MCU sits on the I2C bus. Fix this by moving the MCU node into the I2C controller node. The original patch[1] was OK though. ;-) Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-03Merge branch 'merge'Paul Mackerras
2008-11-19powerpc/mpc832x_rdb: fix swapped ethernet idsMichael Barkowski
ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so that the interfaces do not swap addresses when control passes from U-Boot to the kernel. Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-11-19powerpc/85xx: L2 cache size wrong in 8572DS dtsTrent Piepho
It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no reason to have the wrong value in the dts. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-11-12Merge branch 'linux-2.6' into nextPaul Mackerras
2008-11-08powerpc/86xx: Correct SOC bus-frequency in GE Fanuc SBC610 DTSMartyn Welch
This patch corrects the bus-frequency value provided in the SBC610's dts. Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-11-06powerpc/boot: Allocate more memory for dtbSebastian Siewior
David Gibson suggested that since we are now unconditionally copying the dtb into a malloc()ed buffer, it would be sensible to add a little padding to the buffer at that point, so that further device tree manipulations won't need to reallocate it. This implements that suggestion. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05powerpc: Remove device_type = "rtc" properties in .dts filesAnton Vorontsov
We don't want to encourage the device_type usage. It isn't used in the code, so we can simply remove it from the dts files. Suggested-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-10-31Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"Paul Mackerras
This reverts commit 91a00302959545a9ae423e99732b1e46eb19e877, plus commit 0dcd440120ef12879ff34fc78d7e4abf171c79e4 ("powerpc: Revert CHRP boot wrapper to real-base = 12MB on 32-bit") which depended on it. Commit 91a00302 was causing NVRAM corruption on some pSeries machines, for as-yet unknown reasons, so this reverts it until the cause is identified. Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-10-31Merge branch 'merge' of ↵Paul Mackerras
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into merge
2008-10-31powerpc: Fix format string warning in arch/powerpc/boot/main.cJon Smirl
Fix format string warning in arch/powerpc/boot/main.c. Also correct a typo ("uncomressed") on the same line. BOOTCC arch/powerpc/boot/main.o arch/powerpc/boot/main.c: In function 'prep_kernel': arch/powerpc/boot/main.c:65: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'long unsigned int' Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-10-31powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()David Gibson
There's currently an off-by-one bug in fdt_subnode_offset_namelen() which causes it to keep searching after it's finished the subnodes of the given parent, and into the subnodes of siblings of the original node which come after it in the tree. This bug was introduced in commit ed95d7450dcbfeb45ffc9d39b1747aee82b49a51 ("powerpc: Update in-kernel dtc and libfdt to version 1.2.0"). A patch has already been submitted to dtc/libfdt mainline. We don't really want to pull in a new upstream version during the 2.6.28 cycle, but we should still fix this bug, hence this standalone version of the fix for the in-kernel libfdt. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-10-31powerpc: Remove duplicate DMA entry from mpc8313erdb device treeMike Dyer
Commit 574366128db29e7da609ec1f9c01bf9d80adec87 added a duplicate DMA controller node. Signed-off-by: Mike Dyer <mike.dyer@provision-comm.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-22powerpc: Add del_node() for early boot code to prune inapplicable devices.Mike Ditto
Some platforms have variants that can share most of a flat device tree but need a few devices selectively pruned at boot time. This adds del_node() to ops.h to allow access to the existing fdt_del_node(). Signed-off-by: Mike Ditto <mditto@consentry.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-21Merge commit 'kumar/kumar-for-2.6.28'Benjamin Herrenschmidt
2008-10-20powerpc/83xx: Add DS1339 RTC support for MPC8349E-mITX boards .dtsAnton Vorontsov
The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal is connected to the IPIC's EXT2 interrupt line, the line is shared with Vitesse 8201 Ethernet PHY. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>