| Age | Commit message (Collapse) | Author |
|---|
|
Call chip->eoi(irq) to clear any pending interrupt in case of kdump
shutdown sequence. chip->end(irq) does not serve this purpose.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
To compile kexec on 32-bit we need a few more bits and pieces. Rather
than add empty definitions, we can make crash.c work on 32-bit, with
only a couple of kludges.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (43 commits)
[POWERPC] Use little-endian bit from firmware ibm,pa-features property
[POWERPC] Make sure smp_processor_id works very early in boot
[POWERPC] U4 DART improvements
[POWERPC] todc: add support for Time-Of-Day-Clock
[POWERPC] Make lparcfg.c work when both iseries and pseries are selected
[POWERPC] Fix idr locking in init_new_context
[POWERPC] mpc7448hpc2 (taiga) board config file
[POWERPC] Add tsi108 pci and platform device data register function
[POWERPC] Add general support for mpc7448hpc2 (Taiga) platform
[POWERPC] Correct the MAX_CONTEXT definition
powerpc: minor cleanups for mpc86xx
[POWERPC] Make sure we select CONFIG_NEW_LEDS if ADB_PMU_LED is set
[POWERPC] Simplify the code defining the 64-bit CPU features
[POWERPC] powerpc: kconfig warning fix
[POWERPC] Consolidate some of kernel/misc*.S
[POWERPC] Remove unused function call_with_mmu_off
[POWERPC] update asm-powerpc/time.h
[POWERPC] Clean up it_lp_queue.h
[POWERPC] Skip the "copy down" of the kernel if it is already at zero.
[POWERPC] Add the use of the firmware soft-reset-nmi to kdump.
...
|
|
Cleanup: remove irq_descp() - explicit use of irq_desc[] is shorter and more
readable.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With this patch, kdump uses the firmware soft-reset NMI for two purposes:
1) Initiate the kdump (take a crash dump) by issuing a soft-reset.
2) Break a CPU out of a deadlock condition that is detected during kdump
processing.
When a soft-reset is initiated each CPU will enter
system_reset_exception() and set its corresponding bit in the global
bit-array cpus_in_sr then call die(). When die() finds the CPU's bit set
in cpu_in_sr crash_kexec() is called to initiate a crash dump. The first
CPU to enter crash_kexec() is called the "crashing CPU". All other CPUs
are "secondary CPUs". The secondary CPU's pass through to
crash_kexec_secondary() and sleep. The crashing CPU waits for all CPUs
to enter via soft-reset then boots the kdump kernel (see
crash_soft_reset_check())
When the system crashes due to a panic or exception, crash_kexec() is
called by panic() or die(). The crashing CPU sends an IPI to all other
CPUs to notify them of the pending shutdown. If a CPU is in a deadlock
or hung state with interrupts disabled, the IPI will not be delivered.
The result being, that the kdump kernel is not booted. This problem is
solved with the use of a firmware generated soft-reset. After the
crashing_cpu has issued the IPI, it waits for 10 sec for all CPUs to
enter crash_ipi_callback(). A CPU signifies its entry to
crash_ipi_callback() by setting its corresponding bit in the
cpus_in_crash bit array. After 10 sec, if one or more CPUs have not set
their bit in cpus_in_crash we assume that the CPU(s) is deadlocked. The
operator is then prompted to generate a soft-reset to break the
deadlock. Each CPU enters the soft reset handler as described above.
Two conditions must be handled at this point:
1) The system crashed because the operator generated a soft-reset. See
2) The system had crashed before the soft-reset was generated ( in the
case of a Panic or oops).
The first CPU to enter crash_kexec() uses the state of the kexec_lock to
determine this state. If kexec_lock is already held then condition 2 is
true and crash_kexec_secondary() is called, else; this CPU is flagged as
the crashing CPU, the kexec_lock is acquired and crash_kexec() proceeds
as described above.
Each additional CPUs responding to the soft-reset will pass through
crash_kexec() to kexec_secondary(). All secondary CPUs call
crash_ipi_callback() readying them self's for the shutdown. When ready
they clear their bit in cpus_in_sr. The crashing CPU waits in
kexec_secondary() until all other CPUs have cleared their bits in
cpus_in_sr. The kexec kernel boot is then started.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
In a testament to the utter simplicity and logic of the English
language ;-), I found a single correct use - in kernel/panic.c - and
10-15 incorrect ones.
Signed-Off-By: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
We've seen several bugs caused by interrupt weirdness in the kdump kernel.
Panicking from an interrupt handler means we fail to EOI the interrupt, and
so the second kernel never gets that interrupt ever again. We also see hangs
on JS20 where we take interrupts in the second kernel early during boot.
This patch fixes both those problems, and although it adds more code to the
crash path I think it is the best solution.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The panic CPU is waiting forever due to some large timeout value if some
CPU is not responding to an IPI.
This patch fixes the problem - the maximum waiting period will be
10 seconds and then the kdump boot will go ahead.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
- This contains the arch specific changes for the following the
kdump generic fixes which were already accepted in the upstream.
. Capturing CPU registers (for the case of 'panic' and invoking
the dump using 'sysrq-trigger') from a function (stack frame) which will
be not be available during the kdump boot. Hence, might result in
invalid stack trace.
. Dynamically allocating per cpu ELF notes section instead of
statically for NR_CPUS.
- Fix the compiler warning in prom_init.c.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch fixes the compilation error (shown below) when CONFIG_SMP=n.
arch/powerpc/kernel/crash.c: In function `crash_kexec_prepare_cpus':
arch/powerpc/kernel/crash.c:236: error: implicit declaration of
function `smp_release_cpus'
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Implementing the machine_crash_shutdown which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Disable the
interrupts, shootdown cpus using debugger IPI and collect regs
for all CPUs.
elfcorehdr= specifies the location of elf core header stored by
the crashed kernel. This command line option will be passed by
the kexec-tools to capture kernel.
savemaxmem= specifies the actual memory size that the first kernel
has and this value will be used for dumping in the capture kernel.
This command line option will be passed by the kexec-tools to
capture kernel.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
