Age | Commit message (Collapse) | Author |
|
Add debug statement for map_cpu_to_node; it's useful for cpu hotplug.
Clarify debug statement about not finding the numa reference points
property.
Don't print a meaningless associativity depth (-1) on non-numa systems.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
At boot, the numa code is assigning boot_cpuid to node 0
unconditionally. Basically, numa_setup_cpu is being stupid about it,
but this is the minimal fix -- just call numa_setup_cpu(boot_cpuid)
later, after all nodes have been set online.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc
|
|
|
|
|
|
My patch (d7a5b2ffa1352f0310630934a56aecbdfb617b72) to always panic if
lmb_alloc() fails is broken because it checks alloc < 0, but should be
checking alloc == 0.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Dump a stream of rawbytes with a new 'dr' command.
Produces less output and it is simpler to feed the output to scripts.
Also, dr has no dumpsize limits.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The dynamic add path for PCI Host Bridges can fail to configure children
adapters under P5IOC controllers. It fails to properly fixup bus/device
resources, and it fails to properly enable EEH. Both of these steps
need to occur before any children devices are enabled in
pci_bus_add_devices().
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
remove warnings when building a 64bit kernel.
smp_call_function triggers also with 32bit kernel.
WARNING: vmlinux: duplicate symbol 'smp_call_function' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:164:EXPORT_SYMBOL(smp_call_function);
arch/powerpc/kernel/smp.c:300:EXPORT_SYMBOL(smp_call_function);
WARNING: vmlinux: duplicate symbol 'ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:113:EXPORT_SYMBOL(ioremap);
arch/powerpc/mm/pgtable_64.c:321:EXPORT_SYMBOL(ioremap);
WARNING: vmlinux: duplicate symbol '__ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:117:EXPORT_SYMBOL(__ioremap);
arch/powerpc/mm/pgtable_64.c:322:EXPORT_SYMBOL(__ioremap);
WARNING: vmlinux: duplicate symbol 'iounmap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:118:EXPORT_SYMBOL(iounmap);
arch/powerpc/mm/pgtable_64.c:323:EXPORT_SYMBOL(iounmap);
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We should be memset'ing the data we are pointing to, not the pointer
itself. This is in an error path so we probably don't hit it much.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
corruption
This patch fixes incorrect setting of powersave_nap to 1 on all
PowerMacs, potentially causing memory corruption on some models. This
bug was introuced by me during the 32/64 bits merge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The wording of the CRASH_DUMP Kconfig option is not very clear. It gives you a
kernel that can be used _as_ the kdump kernel, not a kernel that can boot into
a kdump kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Enable the onboard IDE driver for p610, p615 and p630.
They have the CD connected to this card. All other RS/6000 systems with this
controller have no connectors and dont need this option.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Correct the loop for cacheflush. No idea where I copied the code from,
but the original does not work correct. Maybe the flush is not needed.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The recent changes to keep gettimeofday in sync with xtime had the side
effect that it was occasionally possible for the time reported by
gettimeofday to go back by a microsecond. There were two reasons:
(1) when we recalculated the offsets used by gettimeofday every 2^31
timebase ticks, we lost an accumulated fractional microsecond, and
(2) because the update is done some time after the notional start of
jiffy, if ntp is slowing the clock, it is possible to see time go backwards
when the timebase factor gets reduced.
This fixes it by (a) slowing the gettimeofday clock by about 1us in
2^31 timebase ticks (a factor of less than 1 in 3.7 million), and (b)
adjusting the timebase offsets in the rare case that the gettimeofday
result could possibly go backwards (i.e. when ntp is slowing the clock
and the timer interrupt is late). In this case the adjustment will
reduce to zero eventually because of (a).
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The current pcspkr code combines the device and driver registration.
This patch splits these, putting the device registration in the arch
specific code.
PowerPC and MIPS only have the pcspkr present sometimes.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The lparcfg code needs several things which are pretty arcane internal
details and which we don't want to export, which means that lparcfg
doesn't work when built as a module. This makes it a bool instead of
a tristate in the Kconfig so that users can't try to build it as a
module.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Fix various syscall/signal/swapcontext bugs
[PATCH] powerpc: incorrect rmo_top handling in prom_init
[PATCH] powerpc: Fix incorrect pud_ERROR() message
[PATCH] powerpc: Expose SMT and L1 icache snoop userland features
[PATCH] powerpc: Fix windfarm_pm112 not starting all control loops
[PATCH] powerpc: Fix old g5 issues with windfarm
powerpc32: Fix timebase synchronization on 32-bit powermacs
powerpc: Turn off verbose debug output in powermac platform functions
powerpc: Fix might-sleep warning in program check exception handler
|
|
A careful reading of the recent changes to the system call entry/exit
paths revealed several problems, plus some things that could be
simplified and improved:
* 32-bit wasn't testing the _TIF_NOERROR bit in the syscall fast exit
path, so it was only doing anything with it once it saw some other
bit being set. In other words, the noerror behaviour would apply to
the next system call where we had to reschedule or deliver a signal,
which is not necessarily the current system call.
* 32-bit wasn't doing the call to ptrace_notify in the syscall exit
path when the _TIF_SINGLESTEP bit was set.
* _TIF_RESTOREALL was in both _TIF_USER_WORK_MASK and
_TIF_PERSYSCALL_MASK, which is odd since _TIF_RESTOREALL is only set
by system calls. I took it out of _TIF_USER_WORK_MASK.
* On 64-bit, _TIF_RESTOREALL wasn't causing the non-volatile registers
to be restored (unless perhaps a signal was delivered or the syscall
was traced or single-stepped). Thus the non-volatile registers
weren't restored on exit from a signal handler. We probably got
away with it mostly because signal handlers written in C wouldn't
alter the non-volatile registers.
* On 32-bit I simplified the code and made it more like 64-bit by
making the syscall exit path jump to ret_from_except to handle
preemption and signal delivery.
* 32-bit was calling do_signal unnecessarily when _TIF_RESTOREALL was
set - but I think because of that 32-bit was actually restoring the
non-volatile registers on exit from a signal handler.
* I changed the order of enabling interrupts and saving the
non-volatile registers before calling do_syscall_trace_leave; now we
enable interrupts first.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The kbuild system takes advantage of an incorrect behavior in GNU make.
Once this behavior is fixed, all files in the kernel rebuild every time,
even if nothing has changed. This patch ensures kbuild works with both
the incorrect and correct behaviors of GNU make.
For more details on the incorrect behavior, see:
http://lists.gnu.org/archive/html/bug-make/2006-03/msg00003.html
Changes in this patch:
- Keep all targets that are to be marked .PHONY in a variable, PHONY.
- Add .PHONY: $(PHONY) to mark them properly.
- Remove any $(PHONY) files from the $? list when determining whether
targets are up-to-date or not.
Signed-off-by: Paul Smith <psmith@gnu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
yaboot is scrogged and calls us with an invalid stack alignment,
it seems.
Thanks to David Woodhouse to pointing me to the problem.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
On Thu, 2006-03-02 at 19:55 +0100, Olaf Hering wrote:
> My iBook1 has 2 memory regions in reg. Depending on how I boot it
> (vmlinux+initrd) or zImage.initrd, it will not boot with current Linus
> tree.
> rmo_top should be 160MB instead of 32MB.
On logically-partitioned machines the first element of the reg
property in the memory node is defined to be the "RMO" region,
i.e. the memory that the processor can access in real mode. On other
machines the first element has no special meaning, so only take it to
be the RMO region on LPAR machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch makes userland aware of the icache snoop capability of the
POWER5 (and possibly others in the future) and of SMT capabilities.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The variable `timebase' used to transfer the current timebase value
from one cpu to the other in smp_core99_give/take_timebase was only
an unsigned long, i.e. 32 bits on 32-bit machines. It needs to be
64 bits. This makes it a u64, and fixes the issue reported by Kyle
Moffett, that the two cpus see wildly different values for the time
of day.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This is along the lines suggested by Chris Lumens but goes further
in that it leaves the DEBUG symbol undefined, making the DBG macro
empty.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
On 32-bit, the exception prolog for the program check exception doesn't
enable interrupts early on. If it is an illegal instruction exception,
we read the instruction in order to emulate certain instructions, and
the get_user of the instruction triggers a WARN_ON since interrupts
are still disabled. This adds a local_irq_enable() to enable
interrupts before reading the instruction.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch adds mm->task_size to keep track of the task size of a given mm
and uses that to fix the powerpc vdso so that it uses the mm task size to
decide what pages to fault in instead of the current thread flags (which
broke when ptracing).
(akpm: I expect that mm_struct.task_size will become the way in which we
finally sort out the confusion between 32-bit processes and 32-bit mm's. It
may need tweaks, but at this stage this patch is powerpc-only.)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
git+ssh://galak@master.kernel.org/pub/scm/linux/kernel/git/galak/powerpc
|
|
|
|
Before the merge I updated create_pte_mapping() to work for iSeries, by
calling iSeries_hpte_bolt_or_insert. (4c55130b2aa93370f1bf52d2304394e91cf8ee39)
Later we changed iSeries_hpte_insert to cope with the bolting case, and called
that instead from create_pte_mapping() (which was renamed to htab_bolt_mapping)
(3c726f8dee6f55e96475574e9f645327e461884c).
Unfortunately that change introduced a subtle bug, where we pass an absolute
address to iSeries_hpte_insert() where it expects a physical address. This
leads to us calling phys_to_abs() twice on the physical address, which is
seriously bogus.
This only causes a problem if the absolute address from the first translation
can be looked up again in the chunk_map, which depends on the size and layout
of memory. I've seen it fail on one box, but not others.
The minimal fix is to pass the physical address to iSeries_hpte_insert(). For
2.6.17 we should make phys_to_abs() BUG if we try to double-translate an
address.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch fixes a crash in handle_eeh_events,
but ethtool -t still doesnt work right.
...
pepino:~ # cpu 0x3: Vector: 300 (Data Access) at [c00000005192bbe0]
pc: c00000000004a380: .handle_eeh_events+0xe0/0x23c
lr: c00000000004a374: .handle_eeh_events+0xd4/0x23c
sp: c00000005192be60
msr: 9000000000009032
dar: 268
dsisr: 40000000
current = 0xc0000001fe7bf1a0
paca = 0xc00000000048b280
pid = 16322, comm = eehd
enter ? for help
[c00000005192bf00] c00000000004a808 .eeh_event_handler+0xcc/0x130
[c00000005192bf90] c000000000025e00 .kernel_thread+0x4c/0x68
...
(none):/# /usr/sbin/ethtool -i eth0
driver: e100
version: 3.5.10-k2-NAPI
firmware-version: N/A
bus-info: 0000:21:01.0
(none):/# /usr/sbin/ethtool -t eth0
Call Trace:
[C00000000F8DEFF0] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000F8DF0A0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000F8DF150] [C000000000049E58] .eeh_check_failure+0x10c/0x138
[C00000000F8DF1E0] [C0000000002DFDB0] .e100_hw_reset+0x70/0xf4
[C00000000F8DF270] [C0000000002E1BBC] .e100_hw_init+0x2c/0x260
[C00000000F8DF310] [C0000000002E2464] .e100_loopback_test+0x8c/0x220
[C00000000F8DF3C0] [C0000000002E28DC] .e100_diag_test+0xdc/0x16c
[C00000000F8DF490] [C000000000420BE0] .dev_ethtool+0xf24/0x14f8
[C00000000F8DF8F0] [C00000000041F4A8] .dev_ioctl+0x5cc/0x740
[C00000000F8DFA20] [C00000000040FEFC] .sock_ioctl+0x3d0/0x404
[C00000000F8DFAC0] [C0000000000D513C] .do_ioctl+0x68/0x108
[C00000000F8DFB50] [C0000000000D56B0] .vfs_ioctl+0x4d4/0x510
[C00000000F8DFC10] [C0000000000D5740] .sys_ioctl+0x54/0x94
[C00000000F8DFCC0] [C0000000000FB6EC] .ethtool_ioctl+0x11c/0x150
[C00000000F8DFD60] [C0000000000F7E40] .compat_sys_ioctl+0x338/0x3bc
[C00000000F8DFE30] [C00000000000871C] syscall_exit+0x0/0x40
EEH: Detected PCI bus error on device 0000:21:01.0
EEH: This PCI device has failed 1 times since last reboot: <NULL> -
modprobe: FATAL: Could not load /lib/modules/2.6.16-rc4-git7/modules.dep: No such file or directory
Cannot get strings: No such device
(none):/#
(none):/# EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2
(none):/# Call Trace:
[C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154
[C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc
[C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c
[C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c
[C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8
[C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110
[C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250
[C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140
[C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68
EEH: Detected PCI bus error on device <NULL>
EEH: This PCI device has failed 1 times since last reboot: <NULL> -
EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2
Call Trace:
[C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154
[C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc
[C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c
[C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c
[C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8
[C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110
[C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250
[C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140
[C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68
EEH: Detected PCI bus error on device <NULL>
EEH: This PCI device has failed 1 times since last reboot: <NULL> -
EEH: Unable to configure device bridge (-3) for /pci@400000000110/pci@2,2
Call Trace:
[C00000000FA17940] [C00000000000F270] .show_stack+0x74/0x1b4 (unreliable)
[C00000000FA179F0] [C000000000049D04] .eeh_dn_check_failure+0x290/0x2d8
[C00000000FA17AA0] [C00000000001E114] .rtas_read_config+0x120/0x154
[C00000000FA17B40] [C000000000049664] .early_enable_eeh+0x274/0x2bc
[C00000000FA17C00] [C000000000049708] .eeh_add_device_early+0x5c/0x6c
[C00000000FA17C90] [C000000000049748] .eeh_add_device_tree_early+0x30/0x5c
[C00000000FA17D20] [C000000000046568] .pcibios_add_pci_devices+0x8c/0x1f8
[C00000000FA17DD0] [C00000000004A528] .eeh_reset_device+0xe0/0x110
[C00000000FA17E60] [C00000000004A698] .handle_eeh_events+0x140/0x250
[C00000000FA17F00] [C00000000004AC7C] .eeh_event_handler+0xe8/0x140
[C00000000FA17F90] [C000000000025784] .kernel_thread+0x4c/0x68
EEH: Detected PCI bus error on device <NULL>
and so on
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
A bug in the assembly code of the vdso can cause gettimeofday() to hang
or to return incorrect results. The wrong register was used to test for
pending updates of the calibration variables and to create a dependency
for subsequent loads. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Some hotplug driver functions were migrated to the kernel for use by EEH
in commit 2bf6a8fa21570f37fd1789610da30f70a05ac5e3.
Previously, the PCI Hotplug module had been changed to use the new
OFDT-based PCI probe when appropriate:
5fa80fcdca9d20d30c9ecec30d4dbff4ed93a5c6
When rpaphp_pci_config_slot() was moved from the rpaphp driver to the
new kernel function pcibios_add_pci_devices(), the OFDT-based probe
stuff was dropped. This patch restores it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The inline cputime_to_foo and foo_to_cputime conversion functions in
include/asm-powerpc/cputime.h refer to 5 variables, which need to be
exported if those functions are to be usable from modules.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Commit 9ec4b1f356b3bad928ae8e2aa9caebfa737d52df made kprobes not compile
without module support, so just make that clear in the Kconfig file.
Also, since it's marked EXPERIMENTAL, make that dependency explicit too.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
mem= command line option was being ignored in arch/powerpc if we were not
a CONFIG_MULTIPLATFORM (which is handled via prom_init stub). The initial
command line extraction and parsing needed to be moved earlier in the boot
process and have code to actual parse mem= and do something about it.
Also, fixed a compile warning in the file.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
Maple firmware does not need PCI resource allocation, and in fact, it
can cause problems in some strange cases.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Do disable, not enable, the HT APIC IRQ in the function that is
supposed to.
Enable the MPIC IRQ before enabling the downstream APIC IRQ, avoids
potentially losing an interrupt.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Update defconfigs for g5, pseries and generic ppc64. Default choices
for everything, with the following exceptions:
* Enable WINDFARM_PM112 on g5 and ppc64.
* Increase CONFIG_NR_CPUS to 4 in g5_defconfig
* CONFIG_TIGON3=y instead of =m in g5_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
HMT support is currently broken and needs to be reworked to play nicely
with the SMT scheduler. Remove the bit rotten bits for the time being.
I also updated an incorrect comment, we enter __secondary_hold with the
physical cpu id in r3.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
native_hpte_clear has a spinlock recursion problem with the native_tlbie_lock
being called twice, once in native_hpte_clear() and once within tlbie().
Fix the problem by changing the call to tlbie() in native_hpte_clear() to
__tlbie(). It still supports only 4k pages for now.
Signed-off-by: R Sharada <sharada@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Disable OProfile in Kconfig for iSeries to prevent hangs. OProfile
was not originally intended to work with legacy iSeries.
Signed-off-by: Kelly Daly <kelly@au.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
altivec_unavailable_exception is called without setting r3... it looks like
the r3 that actually gets passed in as struct pt_regs *regs is the
undisturbed value of r3 at the time the altivec instruction was encountered.
The user actually gets to choose the pt_regs printed in the Oops!
This fixes the oops by passing the correct pt_regs pointer to
altivec_unavailable_exception.
Signed-off-by: Alan Curry <pacman@TheWorld.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The panic CPU is waiting forever due to some large timeout value if some
CPU is not responding to an IPI.
This patch fixes the problem - the maximum waiting period will be
10 seconds and then the kdump boot will go ahead.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|