| Age | Commit message (Collapse) | Author |
|---|
|
The new Cell EDAC driver needs that file, oprofile also does ugly
path tricks to get to it, it's time to move it to asm-powerpc. While
at it, rename it to be consistent with cell-pmu.h (and dashes look
nicer than underscores anyway).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add '-g' to BOOTCFLAGS if CONFIG_DEBUG_INFO is set.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Since bootdevice never gets initialized, it's always NULL, and hence a
whole pile of code in arch/powerpc/platforms/setup.c never gets used.
(This was the code that originally was there so that the automatic
root partition selection mechanism would prefer a rootish-looking
partition on the device that OF loaded the kernel from over a similar
partition on other devices.)
This removes the unused code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
WARNING: vmlinux.o(.text+0x2ff5c): Section mismatch: reference to .init.text:.pmac_find_ide_boot (between '.note_bootable_part' and '.note_scsi_host')
>From holly_defconfig:
WARNING: vmlinux.o(.text+0x164fe): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
WARNING: vmlinux.o(.text+0x16506): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
>From linkstation_defconfig:
WARNING: vmlinux.o(.text+0x158fe): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
WARNING: vmlinux.o(.text+0x15906): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
>From mpc7448_hpc2_defconfig:
WARNING: vmlinux.o(.text+0x1583e): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
WARNING: vmlinux.o(.text+0x15846): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
>From pmac32_defconfig:
WARNING: vmlinux.o(.text+0x154ca): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'note_scsi_host')
WARNING: vmlinux.o(.text+0x154d2): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'note_scsi_host')
WARNING: vmlinux.o(.text+0x1553c): Section mismatch: reference to .init.text:pmac_find_ide_boot (between 'note_bootable_part' and 'note_scsi_host')
>From ppc64_defconfig:
WARNING: vmlinux.o(.text+0x3acdc): Section mismatch: reference to .init.text:.pmac_find_ide_boot (between '.note_bootable_part' and '.note_scsi_host')
>From prpmc2800_defconfig:
WARNING: vmlinux.o(.text+0x1611e): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
WARNING: vmlinux.o(.text+0x16126): Section mismatch: reference to .init.data:boot_command_line (between 'note_bootable_part' and 'find_via_pmu')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Discussions with firmware architects have confirmed that the bit in
the ibm,pa-features property that indicates support for
cache-inhibited large (>= 64kB) page mappings does in fact mean that
the hypervisor allows 64kB mappings to I/O devices.
Thus we can now enable the code that tests that bit and sets our
CPU_FTR_CI_LARGE_PAGE feature bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The name field of of_platform_driver is just copied into the included
device_driver. By not overriding an already initialised device_driver
name, we can convert the drivers over time to stop using the
of_platform_driver name.
Also we were not copying the owner field from of_platform_driver, so do
the same with it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
DTC now supports "foo","bar" format for lists of strings; use the new
format on the lite5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
On non-QE processors (mpc831x/mpc834x) the SPI clock is the SoC clock.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Apart from that the current code doesn't compile it's also
meaningless with regard to the MPC8568E-MDS' BCSR.
This patch used to reset UCCs properly.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
1. UCC1's RX_DV pin is 16, not 15;
2. UCC1's phy is at 0x7, not 0x1. Schematics says 0x7, and recent
u-boot also using 0x7.
3. Use gianfar's (eTSEC) mdio bus. This is hardware default setup.
4. tx-clock should be CLK16 (GE125, PB31);
5. phy-connection-type is RGMII-ID;
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
8 bytes padding required to match MPC85xx registers layout.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
set_irq_chained_handler overwrites MPIC's handle_irq function
(handle_fasteoi_irq) thus MPIC never gets eoi event from the
cascaded IRQ. This situation hangs MPIC on MPC8568E.
To solve this problem efficiently, QEIC needs pluggable handlers,
specific to the underlaying interrupt controller.
Patch extends qe_ic_init() function to accept low and high interrupt
handlers. To avoid #ifdefs, stack of interrupt handlers specified in
the header file and functions are marked 'static inline', thus
handlers are compiled-in only if actually used (in the board file).
Another option would be to lookup for parent controller and
automatically detect handlers (will waste text size because of
never used handlers, so this option abolished).
qe_ic_init() also changed in regard to support multiplexed high/low
lines as found in MPC8568E-MDS, plus qe_ic_cascade_muxed_mpic()
handler implemented appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
On the majority of 85xx & 86xx we have a register that's ability to
assert HRESET_REQ to reset the board. We refactored that code so it
can be shared between both platforms into fsl_soc.c and removed all
the duplication in each platform directory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
On the Freescale embedded (83xx, 85xx, 86xx) and a few of the discrete
bridges (mpc10x, tsi108) use the new for_each_compatible_node() or
for_each_node_by_type() to provide more exact matching when looking for
PHBs in the device tree.
With the previous code it was possible to match on pci bridges since
we were only matching on device_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The LTSSM register is actual 32-bits wide so we should be doing a
dword access.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The CONFIG_FSL_BOOKE mmu setup code fails when CONFIG_HIGHMEM=y
and the 3 fixed TLB entries cannot exactly map the lowmem size.
Each TLB entry can map 4MB, 16MB, 64MB or 256MB, so the failure
is observed when the kernel lowmem size is not equal to the
sum of up to 3 of those values.
Normally, memory is sized in nice numbers, but I observed this
problem while testing a crash dump kernel. The failure can
also be observed by artificially reducing the kernel's main
memory via the mem= kernel command line parameter.
This commit fixes the problem by setting __initial_memory_limit
in adjust_total_lowmem().
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add basic board support for the MPC8610 HPCD. This does
not include any support the SoC Display or Audio controllers.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loelier <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
According to booting-without-of.txt, compatible should be "fsl_spi" and
mode "cpu" or "qe" for the fsl SPI controllers.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch makes numerous miscellaneous code improvements to the QE library.
1. Remove struct ucc_common and merge ucc_init_guemr() into ucc_set_type()
(every caller of ucc_init_guemr() also calls ucc_set_type()). Modify all
callers of ucc_set_type() accordingly.
2. Remove the unused enum ucc_pram_initial_offset.
3. Refactor qe_setbrg(), also implement work-around for errata QE_General4.
4. Several printk() calls were missing the terminating \n.
5. Add __iomem where needed, and change u16 to __be16 and u32 to __be32 where
appropriate.
6. In ucc_slow_init() the RBASE and TBASE registers in the PRAM were programmed
with the wrong value.
7. Add the protocol type to struct us_info and updated ucc_slow_init() to
use it, instead of always programming QE_CR_PROTOCOL_UNSPECIFIED.
8. Rename ucc_slow_restart_x() to ucc_slow_restart_tx()
9. Add several macros in qe.h (mostly for slow UCC support, but also to
standardize some naming convention) and remove several unused macros.
10. Update ucc_geth.c to use the new macros.
11. Add ucc_slow_info.protocol to specify which QE_CR_PROTOCOL_xxx protcol
to use when initializing the UCC in ucc_slow_init().
12. Rename ucc_slow_pram.rfcr to rbmr and ucc_slow_pram.tfcr to tbmr, since
these are the real names of the registers.
13. Use the setbits, clrbits, and clrsetbits where appropriate.
14. Refactor ucc_set_qe_mux_rxtx().
15. Remove all instances of 'volatile'.
16. Simplify get_cmxucr_reg();
17. Replace qe_mux.cmxucrX with qe_mux.cmxucr[].
18. Updated struct ucc_geth because struct ucc_fast is not padded any more.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
We now generate vdso[32,64].so.dbg as part of the build so
add them to .gitignore
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The PCI nodes on the MPC8568 dts didn't get moved up to be sibilings of the
SOC node when we did that clean up for some reason. Fix that up and some
minor whitespace and adjusting the size of the soc reg property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
According to u-boot/board/mpc8568mds/init.S:
LAW(Local Access Window) configuration:
2) 0xa000_0000 0xbfff_ffff PCIe MEM 512MB
4) 0xe280_0000 0xe2ff_ffff PCIe I/O 8M
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
MPC8568E-MDS have DS1374 chip on the I2C bus, thus let's use it.
This patch also adds #address-cells and #size-cells to the I2C
controllers nodes.
p.s. DS1374 rtc class driver is in the -mm tree, its name is
rtc-rtc-class-driver-for-the-ds1374.patch.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
i2c_board_info used semi-initialized, causing garbage in the
info->flags, and that, in turn, causes various symptoms of i2c
malfunctioning, like PEC mismatches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area). The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.
It is now described with a muram node, similar to QE. The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.
The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated. QE should be able to use this code as well, once
minor fixes are made to its device trees.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add support for the I2C devices handled by the rtc-ds1307 driver to
of_register_i2c_devices.
Cc: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Fix a trivial printk typo in fsl_soc.
Cc: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Previously, Soft_emulate_8xx was called with no implementation, resulting in
build failures whenever building 8xx without math emulation. The
implementation is copied from arch/ppc to resolve this issue.
However, this sort of minimal emulation is not a very good idea other than
for compatibility with existing userspaces, as it's less efficient than
soft-float and can mislead users into believing they have soft-float. Thus,
it is made a configurable option, off by default.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch adds cuboot support for MPC7448HPC2 platform.
The cuImage can be used with legacy u-boot without FDT support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
1. PCI and reset are factored out into pq2.c. I renamed them from m82xx
to pq2 because they won't work on the Integrated Host Processor line of
82xx chips (i.e. 8240, 8245, and such).
2. The PCI PIC, which is nominally board-specific, is used on multiple
boards, and thus is used into pq2ads-pci-pic.c.
3. The new CPM binding is used.
4. General cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
It now uses the new CPM binding and the generic pin/clock functions, and
has assorted fixes and cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The localbus node is used to describe devices that are connected via a chip
select or similar mechanism. The advantages over placing the devices under
the root node are that it can be probed without probing other random things
under the root, and that the description of which chip select a given device
uses can be used to set up mappings if the firmware failed to do so in a
useful manner.
cuboot-pq2 is updated to match the binding; previously, it called itself
chipselect rather than localbus, and used phandle linkage between the
actual bus node and the control node (the current agreement is to simply use
the fully-qualified address of the control registers, and ignore the overlap
with the IMMR node).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This is just a rename patch; internal references to mpc82xx_ads will be
changed in the next one.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
functionality.
m82xx_calibrate_decr(), mpc82xx_ads_show_cpuinfo(), and mpc82xx_halt() do
anything useful beyond what the generic code does.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This provides a generic way for board code to set up CPM pins, rather
than directly poking magic values into registers.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Mostly sparse fixes (__iomem annotations, etc); also, cpm2_immr
is used rather than creating many temporary mappings.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The 8xx can only support a max of 8M during early boot (it seems a lot of
8xx boards only have 8M so the bug was never triggered), but the early
allocator isn't aware of this. The following change makes it able to run
with larger memory.
Signed-off-by: John Traill <john.traill@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The CPU15 erratum on MPC8xx chips can cause incorrect code execution
under certain circumstances, where there is a conditional or indirect
branch in the last word of a page, with a target in the last cache line
of the next page. This patch implements one of the suggested
workarounds, by forcing a TLB miss whenever execution crosses a page
boundary. This is done by invalidating the pages before and after the
one being loaded into the TLB in the ITLB miss handler.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
These let board code set up pins and clocks without having to
put magic numbers directly into the registers.
The clock function is mostly duplicated from the cpm2 version;
hopefully this stuff can be merged at some point.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
1. Keep a global mpc8xx_immr mapping, rather than constantly
creating temporary mappings.
2. Look for new fsl,cpm1 and fsl,cpm1-pic names.
3. Always reset the CPM when not using the udbg console;
this is required in case the firmware initialized a device
that is incompatible with one that the kernel is about to
use.
4. Remove some superfluous casts and header includes.
5. Change a usage of IMAP_ADDR to get_immrbase().
6. Use phys_addr_t, not uint, for dpram_pbase.
7. Various sparse-related fixes, such as __iomem annotations.
8. Remove mpc8xx_show_cpuinfo, which doesn't provide anything
useful beyond the generic cpuinfo handler.
9. Move prototypes for 8xx support functions from board files
to sysdev/commproc.h.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
1. Move CONSISTENT_START on 8xx so that it doesn't overlap the IMMR mapping.
2. The wrong register was being loaded into SPRN_MD_RPN.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
