aboutsummaryrefslogtreecommitdiff
path: root/arch/s390/kernel
AgeCommit message (Collapse)Author
2007-01-09[S390] Fix vmalloc area size calculation.Heiko Carstens
setup_memory_end() uses VMALLOC_END instead of VMALLOC_END_INIT to calculate the maximum supported size of physical memory. Since VMALLOC_END is zero, this will cause a crash on 31 bit systems. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2007-01-09[S390] Fix cpu hotplug (missing 'online' attribute).Heiko Carstens
72486f1f8f0a2bc828b9d30cf4690cf2dd6807fc inverts the logic if an 'online' attribute in /sys/devices/system/cpu/cpuX should appear. So we end up with no hotpluggable cpus at all... Set the hotpluggable value to one to make sure the online attribute appears again. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2007-01-09[S390] memory detection misses 128k.Hongjie Yang
Fix a memory leak problem in the memory detection routines. A memory leak of 128k occurs when we have a contiguous memory with mixed access-mode (read or write) ranges. Signed-off-by: Hongjie Yang <hongjie@us.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-15[S390] Save prefix register for dump on panicMichael Holzheu
The dump tools expect that the saved prefix register points to the lowcore of the dump cpu. Since we set the prefix register to 0 during reipl/dump, we have to save the original prefix register. Before we start the dump program, we copy the original prefix register to the designated location in the lowcore. Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-15[S390] Fix reboot hangMichael Holzheu
We use printks after shutting down all other cpus. This is not allowed and can lead to deadlocks. Therefore the printks have to be removed. Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-15[S390] Fix reboot hang on LPARsMichael Holzheu
Reboot hangs on LPARs without diag308 support. The reason for this is, that before the reboot is done, the channel subsystem is shut down. During the reset on each possible subchannel a "store subchannel" is done. This operation can end in a program check interruption, if the specified subchannel set is not implemented by the hardware. During the reset, currently we do not have a program check handler, which leads to the described kernel bug. We install now a new program check handler for the reboot code to fix this problem. Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-13[PATCH] getting rid of all casts of k[cmz]alloc() callsRobert P. J. Day
Run this: #!/bin/sh for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do echo "De-casting $f..." perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f done And then go through and reinstate those cases where code is casting pointers to non-pointers. And then drop a few hunks which conflicted with outstanding work. Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com> Cc: Mikael Starvik <starvik@axis.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jeff Dike <jdike@addtoit.com> Cc: Greg KH <greg@kroah.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Paul Fulghum <paulkf@microgate.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Karsten Keil <kkeil@suse.de> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: James Bottomley <James.Bottomley@steeleye.com> Cc: Ian Kent <raven@themaw.net> Cc: Steven French <sfrench@us.ibm.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Neil Brown <neilb@cse.unsw.edu.au> Cc: Jaroslav Kysela <perex@suse.cz> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6Linus Torvalds
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: [S390] Poison init section before freeing it. [S390] Use add_active_range() and free_area_init_nodes(). [S390] Virtual memmap for s390. [S390] Update documentation for dynamic subchannel mapping. [S390] Use dev->groups for adding/removing the subchannel attribute group. [S390] Support for disconnected devices reappearing on another subchannel. [S390] subchannel lock conversion. [S390] Some preparations for the dynamic subchannel mapping patch. [S390] runtime switch for qdio performance statistics [S390] New DASD feature for ERP related logging [S390] add reset call handler to the ap bus. [S390] more workqueue fixes. [S390] workqueue fixes. [S390] uaccess_pt: add missing down_read() and convert to is_init().
2006-12-08[PATCH] struct path: convert s390Josef Sipek
Signed-off-by: Josef Sipek <jsipek@fsl.cs.sunysb.edu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08[S390] Use add_active_range() and free_area_init_nodes().Heiko Carstens
Size zones and holes in an architecture independent manner for s390. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-08[S390] Virtual memmap for s390.Heiko Carstens
Virtual memmap support for s390. Inspired by the ia64 implementation. Unlike ia64 we need a mechanism which allows us to dynamically attach shared memory regions. These memory regions are accessed via the dcss device driver. dcss implements the 'direct_access' operation, which requires struct pages for every single shared page. Therefore this implementation provides an interface to attach/detach shared memory: int add_shared_memory(unsigned long start, unsigned long size); int remove_shared_memory(unsigned long start, unsigned long size); The purpose of the add_shared_memory function is to add the given memory range to the 1:1 mapping and to make sure that the corresponding range in the vmemmap is backed with physical pages. It also initialises the new struct pages. remove_shared_memory in turn only invalidates the page table entries in the 1:1 mapping. The page tables and the memory used for struct pages in the vmemmap are currently not freed. They will be reused when the next segment will be attached. Given that the maximum size of a shared memory region is 2GB and in addition all regions must reside below 2GB this is not too much of a restriction, but there is room for improvement. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-07[PATCH] kprobes: enable booster on the preemptible kernelMasami Hiramatsu
When we are unregistering a kprobe-booster, we can't release its instruction buffer immediately on the preemptive kernel, because some processes might be preempted on the buffer. The freeze_processes() and thaw_processes() functions can clean most of processes up from the buffer. There are still some non-frozen threads who have the PF_NOFREEZE flag. If those threads are sleeping (not preempted) at the known place outside the buffer, we can ensure safety of freeing. However, the processing of this check routine takes a long time. So, this patch introduces the garbage collection mechanism of insn_slot. It also introduces the "dirty" flag to free_insn_slot because of efficiency. The "clean" instruction slots (dirty flag is cleared) are released immediately. But the "dirty" slots which are used by boosted kprobes, are marked as garbages. collect_garbage_slots() will be invoked to release "dirty" slots if there are more than INSNS_PER_PAGE garbage slots or if there are no unused slots. Cc: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: "bibo,mao" <bibo.mao@intel.com> Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com> Cc: Yumiko Sugita <yumiko.sugita.yf@hitachi.com> Cc: Satoshi Oshima <soshima@redhat.com> Cc: Hideo Aoki <haoki@redhat.com> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07[PATCH] elf: Always define elf_addr_t in linux/elf.hMagnus Damm
Define elf_addr_t in linux/elf.h. The size of the type is determined using ELF_CLASS. This allows us to remove the defines that today are spread all over .c and .h files. Signed-off-by: Magnus Damm <magnus@valinux.co.jp> Cc: Daniel Jacobowitz <drow@false.org> Cc: Roland McGrath <roland@redhat.com> Cc: Jakub Jelinek <jakub@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-04[S390] Memory detection fixes.Heiko Carstens
VMALLOC_END on 31bit should be 0x8000000UL instead of 0x7fffffffL. The page mask which is used to make sure memory_end is on 4MB/2MB boundary is wrong and not needed. Therefore remove it. Make sure a vmalloc area does also exist and work on (future) machines with 4TB and more memory. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] lockdep: show held locks when showing a stackdumpHeiko Carstens
Follow i386/x86_64: lockdep can be used to print held locks when printing a backtrace. This can be useful when debugging things like 'scheduling while atomic' asserts. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] Use diag260 for memory size detection.Heiko Carstens
Avoid the tprot loop if diag260 works and reports that there are no holes in memory. The tprot instruction can lead to a significant delay in the ipl process if the virtual guest has a lot of memory and the host is under memory pressure. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] pfault code cleanup.Heiko Carstens
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] Cleanup memory_chunk array usage.Heiko Carstens
Need this at yet another file and don't want to add yet another extern... Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] Misaligned wait PSW at memory detection.Heiko Carstens
If the memory detection code would ever reach the point where it would load the wait psw, it would generate a specification exception and the system would crash at ipl time. This is because of a misaligned wait psw. It needs to be on a double word boundary instead of a word boundary. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] cpu shutdown reworkHeiko Carstens
Let one master cpu kill all other cpus instead of sending an external interrupt to all other cpus so they can kill themselves. Simplifies reipl/shutdown functions a lot. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] cpcmd <-> __cpcmd calling issuesHeiko Carstens
In case of reipl cpcmd gets called when all other cpus are not running anymore. To prevent deadlocks change __cpcmd so that it doesn't take any locks and call cpcmd or __cpcmd, whatever is correct in the current context. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] Reset infrastructure for re-IPL.Heiko Carstens
In case of re-IPL and diag308 doesn't work we have to reset all devices manually and wait synchronously that each reset finished. This patch adds the necessary infrastucture and the first exploiter of it. Subsystems that need to add a function that needs to be called at re-IPL may register/unregister this function via struct reset_call { struct reset_call *next; void (*fn)(void); }; void register_reset_call(struct reset_call *reset); void unregister_reset_call(struct reset_call *reset); When the registered function get called the context is: - all cpus beside the current one are stopped - all machine checks and interrupts are disabled - prefixing is disabled - a default machine check handler is available for use The registered functions may not take any locks are sleep. For the common I/O layer part of this patch: Introduce a reset_call css_reset that does the following: - clear all subchannels - perform a rchp on all channel paths and wait for the resulting machine checks This replaces the calls to clear_all_subchannels() and cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now uses reipl_find_schid() to determine the subchannel id for a given device id. Also remove cio_reset_channel_paths() and friends since they are not needed anymore. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] Use diag instead of ccw reipl.Michael Holzheu
Since the diag 308 reipl method is superior to the ccw method, we should use it whenever it is possible. We can do that, if the user has not specified a new reipl ccw device and the system has been ipled from a ccw device. Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] No panic for failed rebootMichael Holzheu
If reboot fails (e.g. because wrong devno has been specified by the user), we should just stop all cpus, but should not trigger a kernel panic. Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] Add ipl/reipl loadparm attribute.Michael Holzheu
If multiple kernel images are installed on one DASD, the loadparm can be used to select the boot configuration. This patch introduces the following two new sysfs attributes: /sys/firmware/ipl/loadparm: shows loadparm of current system (ro) /sys/firmware/reipl/ccw/loadparm: loadparm used for next reboot (rw) Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-12-04[S390] remove salipl memory detection.Christian Borntraeger
The SALIPL entry point has an needless memory detection routine as we later check the memory size again. The SALIPL code also uses diagnose 0x060 if we are running under VM, but this diagnose is not compatible with the 64 bit addressing mode. The solution is to get rid of this code and rely on the memory detection in the startup code. Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-11-06[S390] IRQs too early enabled.Heiko Carstens
setup_lowcore() calls ctl_set_bit() which returns withs interrupts enabled. The setup arch code is not supposed to enable interrupts that early. Therefore use the __ctl_set_bit() variant. This fixes the not working lock dependency validator on non 64 bit systems. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-11-06[S390] revert add_active_range() usage patch.Heiko Carstens
Commit 7676bef9c183fd573822cac9992927ef596d584c breaks DCSS support on s390. DCSS needs initialized struct pages to work. With the usage of add_active_range() only the struct pages for physically present pages are initialized. This could be fixed if the DCSS driver would initiliaze the struct pages itself, but this doesn't work too. This is because the mem_map array does not include holes after the last present memory area and therefore there is nothing that could be initialized. To fix this and to avoid some dirty hacks revert this patch for now. Will be added later when we move to a virtual mem_map. Cc: Carsten Otte <cotte@de.ibm.com> Cc: Adrian Bunk <bunk@stusta.de> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-28Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6Linus Torvalds
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: [S390] cio: Make ccw_device_register() static. [S390] Improve AP bus device removal. [S390] uaccess error handling. [S390] cio: css_probe_device() must be called enabled. [S390] Initialize interval value to 0. [S390] sys_getcpu compat wrapper.
2006-10-27[PATCH] vmlinux.lds: consolidate initcall sectionsAndrew Morton
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table, teach all the architectures to use it. This is a prerequisite for a patch which performs initcall synchronisation for multithreaded-probing. Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> [ Added AVR32 as well ] Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-27[S390] uaccess error handling.Heiko Carstens
Consider return values for all user space access function and return -EFAULT on error. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-27[S390] sys_getcpu compat wrapper.Paul Mundt
Looking at the new syscall additions, I noticed that sys_getcpu_wrapper wraps in to sys_tee, in what appears to be a copy and paste error. Switch it to point to sys_getcpu.. Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-18[S390] Wire up epoll_pwait syscall.Heiko Carstens
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2006-10-18[S390] fix vmlinux link when CONFIG_SYSIPC=nCedric Le Goater
Fix the following compile error: CC init/version.o LD init/built-in.o LD .tmp_vmlinux1 arch/s390/kernel/built-in.o(.text+0xdba4): In function `sys32_ipc': : undefined reference to `compat_sys_semtimedop' arch/s390/kernel/built-in.o(.text+0xdbee): In function `sys32_ipc': : undefined reference to `compat_sys_semctl' arch/s390/kernel/built-in.o(.text+0xdc08): In function `sys32_ipc': : undefined reference to `compat_sys_msgsnd' arch/s390/kernel/built-in.o(.text+0xdc30): In function `sys32_ipc': : undefined reference to `compat_sys_msgrcv' arch/s390/kernel/built-in.o(.text+0xdc58): In function `sys32_ipc': : undefined reference to `compat_sys_msgctl' arch/s390/kernel/built-in.o(.text+0xdc76): In function `sys32_ipc': : undefined reference to `compat_sys_shmat' arch/s390/kernel/built-in.o(.text+0xdcb0): In function `sys32_ipc': : undefined reference to `compat_sys_shmctl' make: *** [.tmp_vmlinux1] Error 1 Signed-off-by: Cedric Le Goater <clg@fr.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-11Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6Linus Torvalds
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: [S390] stacktrace bug. [S390] cio: remove casts from/to (void *). [S390] cio: Remove grace period for vary off chpid. [S390] cio: Use ccw_dev_id and subchannel_id in ccw_device_private [S390] monwriter kzalloc size. [S390] cio: add missing KERN_INFO printk header. [S390] irq change improvements.
2006-10-11[PATCH] remove bogus arch-specific syscall exportsAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-11[S390] stacktrace bug.Christian Borntraeger
The latest kernel 2.6.19-rc1 triggers a bug in the s390 specific stack trace code when compiled with gcc 3.4. This patch fixes the latest lock dependency validator code (2.6.19-rc1) on s390 gcc 3.4. The variable sp was fixed to r15 (which is the stack pointer in the s390 abi) and assigned new values to r15. Therefore, gcc 3.4 assigns a new value to r15 and does not restore it on exit (r15 is supposed to be call save) - the kernel stack is broken. Avoid trouble by not assigning any new value to sp (r15). Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-11[S390] irq change improvements.Heiko Carstens
Remove the last few places where a pointer to pt_regs gets passed. Also make sure we call set_irq_regs() before irq_enter() and after irq_exit(). This doesn't fix anything but makes sure s390 looks the same like all other architectures. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-09[PATCH] s390 traps.c __user annotationsAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-06[S390] Use CONFIG_GENERIC_TIME and define TOD clock source.Martin Schwidefsky
Fix too slow clock by using CONFIG_GENERIC_TIME and adding a clock source for the s390 time-of-day clock. As added benefit we get rid of the s390 specific definition of do_gettimeofday and do_settimeofday. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-06[S390] irq change build fixes.Heiko Carstens
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-04[S390] Have s390 use add_active_range() and free_area_init_nodes.Heiko Carstens
Size zones and holes in an architecture independent manner for s390. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2006-10-04[S390] Remove crept in whitespace from head*.S again.Heiko Carstens
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2006-10-04[S390] Wire up sys_getcpu system call.Heiko Carstens
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2006-10-04[S390] user-copy optimization fallout.Martin Schwidefsky
Fix new restore_sigregs function. It copies the user space copy of the old psw without correcting the psw.mask and the psw.addr high order bit. While we are at it, simplify save_sigregs a bit. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2006-10-04Remove all inclusions of <linux/config.h>Dave Jones
kbuild explicitly includes this at build time. Signed-off-by: Dave Jones <davej@redhat.com>
2006-10-03[PATCH] VFS: Make filldir_t and struct kstat deal in 64-bit inode numbersDavid Howells
These patches make the kernel pass 64-bit inode numbers internally when communicating to userspace, even on a 32-bit system. They are required because some filesystems have intrinsic 64-bit inode numbers: NFS3+ and XFS for example. The 64-bit inode numbers are then propagated to userspace automatically where the arch supports it. Problems have been seen with userspace (eg: ld.so) using the 64-bit inode number returned by stat64() or getdents64() to differentiate files, and failing because the 64-bit inode number space was compressed to 32-bits, and so overlaps occur. This patch: Make filldir_t take a 64-bit inode number and struct kstat carry a 64-bit inode number so that 64-bit inode numbers can be passed back to userspace. The stat functions then returns the full 64-bit inode number where available and where possible. If it is not possible to represent the inode number supplied by the filesystem in the field provided by userspace, then error EOVERFLOW will be issued. Similarly, the getdents/readdir functions now pass the full 64-bit inode number to userspace where possible, returning EOVERFLOW instead when a directory entry is encountered that can't be properly represented. Note that this means that some inodes will not be stat'able on a 32-bit system with old libraries where they were before - but it does mean that there will be no ambiguity over what a 32-bit inode number refers to. Note similarly that directory scans may be cut short with an error on a 32-bit system with old libraries where the scan would work before for the same reasons. It is judged unlikely that this situation will occur because modern glibc uses 64-bit capable versions of stat and getdents class functions exclusively, and that older systems are unlikely to encounter unrepresentable inode numbers anyway. [akpm: alpha build fix] Signed-off-by: David Howells <dhowells@redhat.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-02[PATCH] provide kernel_execve on all architecturesArnd Bergmann
This adds the new kernel_execve function on all architectures that were using _syscall3() to implement execve. The implementation uses code from the _syscall3 macros provided in the unistd.h header file. I don't have cross-compilers for any of these architectures, so the patch is untested with the exception of i386. Most architectures can probably implement this in a nicer way in assembly or by combining it with the sys_execve implementation itself, but this should do it for now. [bunk@stusta.de: m68knommu build fix] [markh@osdl.org: build fix] [bero@arklinux.org: build fix] [ralf@linux-mips.org: mips fix] [schwidefsky@de.ibm.com: s390 fix] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Andi Kleen <ak@muc.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ian Molton <spyro@f2s.com> Cc: Mikael Starvik <starvik@axis.com> Cc: David Howells <dhowells@redhat.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Hirokazu Takata <takata.hirokazu@renesas.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp> Cc: Richard Curnow <rc@rc0.org.uk> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp> Cc: Chris Zankel <chris@zankel.net> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org> Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-02[PATCH] nsproxy: move init_nsproxy into kernel/nsproxy.cSerge E. Hallyn
Move the init_nsproxy definition out of arch/ into kernel/nsproxy.c. This avoids all arches having to be updated. Compiles and boots on s390. Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Cc: Kirill Korotaev <dev@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: Andrey Savochkin <saw@sw.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-02[PATCH] namespaces: add nsproxySerge E. Hallyn
This patch adds a nsproxy structure to the task struct. Later patches will move the fs namespace pointer into this structure, and introduce a new utsname namespace into the nsproxy. The vserver and openvz functionality, then, would be implemented in large part by virtualizing/isolating more and more resources into namespaces, each contained in the nsproxy. [akpm@osdl.org: build fix] Signed-off-by: Serge Hallyn <serue@us.ibm.com> Cc: Kirill Korotaev <dev@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: Andrey Savochkin <saw@sw.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>