| Age | Commit message (Collapse) | Author |
|---|
|
Doing a 'flushw' every stack trace capture creates so much overhead
that it makes lockdep next to unusable.
We only care about the frame pointer chain and the function caller
program counters, so flush those by hand to the stack frame.
This is significantly more efficient than a 'flushw' because:
1) We only save 16 bytes per active register window to the stack.
2) This doesn't push the entire register window context of the current
call chain out of the cpu, forcing register window fill traps as we
return back down.
Note that we can't use 'restore' and 'save' instructions to move
around the register windows because that wouldn't work on Niagara
processors. They optimize 'save' into a new register window by
simply clearing out the registers instead of pulling them in from
the on-chip register window backing store.
Based upon a report by Tom Callaway.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was caught and identified by Greg Onufer.
Since we setup the 256M/4M bitmap table after taking over the trap
table, it's possible for some 4M mapping to get loaded in the TLB
beforhand which later will be 256M mappings.
This can cause illegal TLB multiple-match conditions. Fix this by
setting up the bitmap before we take over the trap table.
Next, __flush_tlb_all() was not doing anything on hypervisor
platforms. Fix by adding sun4v_mmu_demap_all() and calling it.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we chain IVEC entries using 32-bit "pointers"
because we know that the ivector_table is in the main
kernel image, thus below 4GB.
This uses proper 64-bit pointers instead.
Whilst this bloats up the kernel image size, this sets
the infrastructure necessary to significantly shrink the
kernel size by using physical addresses and dynamically
allocating the ivector table.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
First argument is LDC channel ID, then mapping cookie,
then the MTE revoke cookie.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the system supports hypervisor based statistics, allow them to
be fetched, enabled, and disabled via sysfs.
Enable and disable via the boolean:
/sys/devices/systems/cpu/cpuN/mmustat_enable
Statistic values are provided under:
/sys/devices/systems/cpu/cpuN/mmu_status/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sed 's/scv/svc/'
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several interfaces were missing and others misnumbered or
improperly documented.
Also, make sure to check the return value when registering
the kernel TSBs with the hypervisor. This helped to find
the 4MB kernel TSB alignment bug fixed in a previous changeset.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hypervisor interfaces need to be negotiated in order to use
some API calls reliably. So add a small set of interfaces
to request API versions and query current settings.
This allows us to fix some bugs in the hypervisor console:
1) If we can negotiate API group CORE of at least major 1
minor 1 we can use con_read and con_write which can improve
console performance quite a bit.
2) When we do a console write request, we should hold the
spinlock around the whole request, not a byte at a time.
What would happen is that it's easy for output from
different cpus to get mixed with each other.
3) Use consistent udelay() based polling, udelay(1) each
loop with a limit of 1000 polls to handle stuck hypervisor
console.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I added the entries for the robust futex syscall entries, I
forgot to bump NR_SYSCALLS. The current situation is error-prone
because NR_SYSCALLS lives in entry.S where the system call limit
checks are enforced. Move the definition to asm/unistd.h in order to
make this mistake much more difficult to make.
And wire up sys_migrate_pages since the powerpc folks implemented the
compat wrapper for us.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This is the long overdue conversion of sparc64 over to
the generic IRQ layer.
The kernel image is slightly larger, but the BSS is ~60K
smaller due to the reduced size of struct ino_bucket.
A lot of IRQ implementation details, including ino_bucket,
were moved out of asm-sparc64/irq.h and are now private to
arch/sparc64/kernel/irq.c, and most of the code in irq.c
totally disappeared.
One thing that's different at the moment is IRQ distribution,
we do it at enable_irq() time. If the cpu mask is ALL then
we round-robin using a global rotating cpu counter, else
we pick the first cpu in the mask to support single cpu
targetting. This is similar to what powerpc's XICS IRQ
support code does.
This works fine on my UP SB1000, and the SMP build goes
fine and runs on that machine, but lots of testing on
different setups is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the first in a series of cleanups that will hopefully
allow a seamless attempt at using the generic IRQ handling
infrastructure in the Linux kernel.
Define PIL_DEVICE_IRQ and vector all device interrupts through
there.
Get rid of the ugly pil0_dummy_{bucket,desc}, instead vector
the timer interrupt directly to a specific handler since the
timer interrupt is the only event that will be signaled on
PIL 14.
The irq_worklist is now in the per-cpu trap_block[].
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were several bugs in the SUN4V cpu mondo dispatch code.
In fact, if we ever got a EWOULDBLOCK or other error from
the hypervisor call, we'd potentially send a cpu mondo multiple
times to the same cpu and even worse we could loop until the
timeout resending the same mondo over and over to such cpus.
So let's bulletproof this thing as follows:
1) Implement cpu_mondo_send() and cpu_state() hypervisor calls
in arch/sparc64/kernel/entry.S, add prototypes to asm/hypervisor.h
2) Don't build and update the cpulist using inline functions, this
was causing the cpu mask to not get updated in the caller.
3) Disable interrupts during the entire mondo send, otherwise our
cpu list and/or mondo block could get overwritten if we take
an interrupt and do a cpu mondo send on the current cpu.
4) Check for all possible error return types from the cpu_mondo_send()
hypervisor call. In particular:
HV_EOK) Our work is done, all cpus have received the mondo.
HV_CPUERROR) One or more of the cpus in the cpu list we passed
to the hypervisor are in error state. Use cpu_state()
calls over the entries in the cpu list to see which
ones. Record them in "error_mask" and report this
after we are done sending the mondo to cpus which are
not in error state.
HV_EWOULDBLOCK) We need to keep trying.
Any other error we consider fatal, we report the event and exit
immediately.
5) We only timeout if forward progress is not made. Forward progress
is defined as having at least one cpu get the mondo successfully
in a given cpu_mondo_send() call. Otherwise we bump a counter
and delay a little. If the counter hits a limit, we signal an
error and report the event.
Also, smp_call_function_mask() error handling reports the number
of cpus incorrectly.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to use the real hardware processor ID when
targetting interrupts, not the "define to 0" thing
the uniprocessor build gives us.
Also, fill in the Node-ID and Agent-ID fields properly
on sun4u/Safari.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call it from register_one_mondo().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not PCI specific, it is for all system interrupts.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sun4v uses ASI_MMU instead of ASI_DMMU
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This, as well as making the code cleaner, allows a simplification in
the TSB miss handling path.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On uniprocessor, it's always zero for optimize that.
On SMP, the jmpl to the stub kills the return address stack in the cpu
branch prediction logic, so expand the code sequence inline and use a
code patching section to fix things up. This also always better and
explicit register selection, which will be taken advantage of in a
future changeset.
The hard_smp_processor_id() function is big, so do not inline it.
Fix up tests for Jalapeno to also test for Serrano chips too. These
tests want "jbus Ultra-IIIi" cases to match, so that is what we should
test for.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just flip the bit off of whatever it's currently set to.
PSTATE_IE is guarenteed to be enabled when we get here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer needed now that we no longer have hard-coded
alternate global register usage.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
UltraSPARC has special sets of global registers which are switched to
for certain trap types. There is one set for MMU related traps, one
set of Interrupt Vector processing, and another set (called the
Alternate globals) for all other trap types.
For what seems like forever we've hard coded the values in some of
these trap registers. Some examples include:
1) Interrupt Vector global %g6 holds current processors interrupt
work struct where received interrupts are managed for IRQ handler
dispatch.
2) MMU global %g7 holds the base of the page tables of the currently
active address space.
3) Alternate global %g6 held the current_thread_info() value.
Such hardcoding has resulted in some serious issues in many areas.
There are some code sequences where having another register available
would help clean up the implementation. Taking traps such as
cross-calls from the OBP firmware requires some trick code sequences
wherein we have to save away and restore all of the special sets of
global registers when we enter/exit OBP.
We were also using the IMMU TSB register on SMP to hold the per-cpu
area base address, which doesn't work any longer now that we actually
use the TSB facility of the cpu.
The implementation is pretty straight forward. One tricky bit is
getting the current processor ID as that is different on different cpu
variants. We use a stub with a fancy calling convention which we
patch at boot time. The calling convention is that the stub is
branched to and the (PC - 4) to return to is in register %g1. The cpu
number is left in %g6. This stub can be invoked by using the
__GET_CPUID macro.
We use an array of per-cpu trap state to store the current thread and
physical address of the current address space's page tables. The
TRAP_LOAD_THREAD_REG loads %g6 with the current thread from this
table, it uses __GET_CPUID and also clobbers %g1.
TRAP_LOAD_IRQ_WORK is used by the interrupt vector processing to load
the current processor's IRQ software state into %g6. It also uses
__GET_CPUID and clobbers %g1.
Finally, TRAP_LOAD_PGD_PHYS loads the physical address base of the
current address space's page tables into %g7, it clobbers %g1 and uses
__GET_CPUID.
Many refinements are possible, as well as some tuning, with this stuff
in place.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also, the Solaris syscall table is sized differrently,
and does not go beyond entry 255, so trim off the excess
entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To let new syscalls through.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This also includes by necessity _TIF_RESTORE_SIGMASK support,
which actually resulted in a lot of cleanups.
The sparc signal handling code is quite a mess and I should
clean it up some day.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't clobber register %l0 while checking TI_SYS_NOERROR value in
syscall return path. This bug was introduced by:
db7d9a4eb700be766cc9f29241483dbb1e748832
Problem narrowed down by Luis F. Ortiz and Richard Mortimer.
I tried using %l2 as suggested by Luis and that works for me.
Looking at the code I wonder if it makes sense to simplify the code
a little bit. The following works for me but I'm not sure how to
exercise the "NOERROR" codepath.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to use stricter memory barriers around the block
load and store instructions we use to save and restore the
FPU register file.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of code patching to handle the page size fields in
the context registers, just use variables from which we get
the proper values.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At boot time, determine the D-cache, I-cache and E-cache size and
line-size. Use them in cache flushes when appropriate.
This change was motivated by discovering that the D-cache on
UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the
Cheetah error handlers were assuming a 32K size.
There are still some pieces of code that are hard coding things and
will need to be fixed up at some point.
While we're here, fix the D-cache and I-cache parity error handlers
to run with interrupts disabled, and when the trap occurs at trap
level > 1 log the event via a counter displayed in /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Arrange the modules, OBP, and vmalloc areas such that a range
verification can be done quite minimally.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We only need to expand this thing once, saving some
text section space.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current uncorrectable error handling was poor enough
that the processor could just loop taking the same
trap over and over again. Fix things up so that we
at least get a log message and perhaps even some register
state.
In the process, much consolidation became possible,
particularly with the correctable error handler.
Prefix assembler and C function names with "spitfire"
to indicate that these are for Ultra-I/II/IIi/IIe only.
More work is needed to make these routines robust and
featureful to the level of the Ultra-III error handlers.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify we really are taking a data access exception trap, at TL1, from
one of the window spill/fill handlers.
Else call a new function, data_access_exception_tl1, to log the error.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) Read ASI_IMMU SFSR not ASI_DMMU.
2) IMMU has no SFAR, read TPC instead
3) Delete old and incorrect comment about the DTLB protection
trap having a dependency on the SFSR contents in order to
function correctly
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These two bits were accesses non-atomically from assembler
code. So, in order to eliminate any potential races resulting
from that, move these pieces of state into two bytes elsewhere
in struct thread_info.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also fix a bug in 32-bit syscall tracing. We forgot to update
this code when we moved over to the convention that all 32-bit
syscall arguments are zero extended by default.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows a PCI controller to shim into IRQ delivery
so that DMA queues can be drained, if necessary.
If some bus specific code needs to run before an IRQ
handler is invoked, the bus driver simply needs to setup
the function pointer in bucket->irq_info->pre_handler and
the two args bucket->irq_info->pre_handler_arg[12].
The Schizo PCI driver is converted over to use a pre-handler
for the DMA write-sync processing it needs when a device
is behind a PCI->PCI bus deeper than the top-level APB
bridges.
While we're here, clean up all of the action allocation
and handling. Now, we allocate the irqaction as part of
the bucket->irq_info area. There is an array of 4 irqaction
(for PCI irq sharing) and a bitmask saying which entries
are active.
The bucket->irq_info is allocated at build_irq() time, not
at request_irq() time. This simplifies request_irq() and
free_irq() tremendously.
The SMP dynamic IRQ retargetting code got removed in this
change too. It was disabled for a few months now, and we
can resurrect it in the future if we want.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
