| Age | Commit message (Collapse) | Author |
|---|
|
Most of contents in crash are same.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Preperatory patch to allow crash_32/64.c merging
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The previous patch wasn't correctly handling the 'count' variable. If
a CPU gave bad results on the 1st or 2nd run but good results on the
3rd, it wouldn't do the correct thing. No idea if any such CPU
exists, but the patch below handles that case by discarding the bad
runs.
If a bad result (too quick, or too slow) occurs on any of the 3 runs
it will be discarded.
Also updated some comments to explain what's going on.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
I ran into this problem on a system that was unable to obtain NTP sync
because the clock was running very slow (over 10000ppm slow). ntpd had
declared all of its peers 'reject' with 'peer_dist' reason.
On investigation, the tsc_khz variable was significantly incorrect
causing xtime to run slow. After a reboot tsc_khz was correct so I
did a reboot test to see how often the problem occurred:
Test was done on a 2000 Mhz Xeon system. Of 689 reboots, 8 of them
had unacceptable tsc_khz values (>500ppm):
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 21 3.048%
1999800 - 1999850 166 24.128%
1999850 - 1999900 241 35.029%
1999900 - 1999950 211 30.669%
1999950 - 2000000 42 6.105%
2000000 - 2000000 0 0.000%
2000050 - 2000100 0 0.000%
[...]
2000100 - 2015000 1 0.145% << BAD
2015000 - 2030000 6 0.872% << BAD
2030000 - 2045000 1 0.145% << BAD
2045000 < 0 0.000%
The worst boot was 2032.577 Mhz, over 1.5% off!
It appears that on rare occasions, mach_countup() is taking longer to
complete than necessary.
I suspect that this is caused by the CPU taking a periodic SMI
interrupt right at the end of the 30ms calibration loop. This would
cause the loop to delay while the SMI BIOS hander runs. The resulting
TSC value is beyond what it actually should be resulting in a higher
tsc_khz.
The below patch makes native_calculate_cpu_khz() take the best
(shortest duration, lowest khz) run of it's 3 calibration loops. If a
SMI goes off causing a bad result (long duration, higher khz) it will
be discarded.
With the patch applied, 300 boots of the same system produce good
results:
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 30 10.000%
1999800 - 1999850 166 55.333%
1999850 - 1999900 89 29.667%
1999900 - 1999950 15 5.000%
1999950 < 0 0.000%
Problem was found and tested against 2.6.18. Patch is against 2.6.22.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
1) This allows us to get alot closer to booting bzImages.
2) It means we don't have to know page_offset.
3) The Guest needs to modify the boot pagetables to create the
PAGE_OFFSET mapping before jumping to C code.
4) guest_pa() walks the page tables rather than using page_offset.
5) We don't use page_offset to figure out whether to emulate: it was
always kinda quesationable, and won't work for instructions done
before remapping (bzImage unpacking in particular).
6) We still want the kernel address for tlb flushing: have the initial
hypercall give us that, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
* 'sg' of git://git.kernel.dk/linux-2.6-block:
Add CONFIG_DEBUG_SG sg validation
Change table chaining layout
Update arch/ to use sg helpers
Update swiotlb to use sg helpers
Update net/ to use sg helpers
Update fs/ to use sg helpers
[SG] Update drivers to use sg helpers
[SG] Update crypto/ to sg helpers
[SG] Update block layer to use sg helpers
[SG] Add helpers for manipulating SG entries
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Add the BSS to the resource tree just as kernel text and kernel data are in
the resource tree. The main reason behind this is to avoid crashkernel
reservation in that area.
While it's not strictly necessary to have the BSS in the resource tree (the
actual collision detection is done in the reserve_bootmem() function before),
the usage of the BSS resource should be presented to the user in /proc/iomem
just as Kernel data and Kernel code.
Note: The patch currently is only implemented for x86 and ia64 (because
efi_initialize_iomem_resources() has the same signature on i386 and ia64).
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we fix all the opensource gfx drivers to use the DMA api's, at that time
we can yank this config options out.
[jengelh@computergmbh.de: Kconfig fixes]
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MSI interrupt handler registrations and fault handling support for Intel-IOMMU
hadrware.
This patch enables the MSI interrupts for the DMA remapping units and in the
interrupt handler read the fault cause and outputs the same on to the console.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Actual intel IOMMU driver. Hardware spec can be found at:
http://www.intel.com/technology/virtualization
This driver sets X86_64 'dma_ops', so hook into standard DMA APIs. In this
way, PCI driver will get virtual DMA address. This change is transparent to
PCI drivers.
[akpm@linux-foundation.org: remove unneeded cast]
[akpm@linux-foundation.org: build fix]
[bunk@stusta.de: fix duplicate CONFIG_DMAR Makefile line]
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch uses the updated boot protocol to do paravirtualized boot.
If the boot version is >= 2.07, then it will do two things:
1. Check the bootparams loadflags to see if we should reload the
segment registers and clear interrupts. This is appropriate
for normal native boot and some paravirtualized environments, but
inapproprate for others.
2. Check the hardware architecture, and dispatch to the appropriate
kernel entrypoint. If the bootloader doesn't set this, then we
simply do the normal boot sequence.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Updates for version 2.07 of the boot protocol. This includes:
load_flags.KEEP_SEGMENTS- flag to request/inhibit segment reloads
hardware_subarch - what subarchitecture we're booting under
hardware_subarch_data - per-architecture data
The intention of these changes is to make booting a paravirtualized
kernel work via the normal Linux boot protocol.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
|
|
Signed-off-by: Josh Triplett <josh@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Spelling fixes in arch/x86_64/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Spelling fixes in arch/i386/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
* ssh://master.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-x86: (33 commits)
x86: convert cpuinfo_x86 array to a per_cpu array
x86: introduce frame_pointer() and stack_pointer()
x86 & generic: change to __builtin_prefetch()
i386: do not BUG_ON() when MSR is unknown
x86: acpi use cpu_physical_id
x86: convert cpu_llc_id to be a per cpu variable
x86: convert cpu_to_apicid to be a per cpu variable
i386: introduce "used_vectors" bitmap which can be used to reserve vectors.
x86: use raw locks during oopses
x86: honor _PAGE_PSE bit on page walks
i386: do cpuid_device_create() in CPU_UP_PREPARE instead of CPU_ONLINE.
x86: implement missing x86_64 function smp_call_function_mask()
x86: use descriptor's functions instead of inline assembly
i386: consolidate show_regs and show_registers for i386
i386: make callgraph use dump_trace() on i386/x86_64
x86: enable iommu_merge by default
i386: i386 add AMD64 Barcelona PMU MSR definitions to msr.h
x86: Unify i386 and x86-64 early quirks
x86: enable HPET on ICH3 and ICH4
x86: force enable HPET on VT8235/8237 chipsets
...
Manually fix trivial conflict with task pid container helper changes in
arch/x86/kernel/process_32.c
|
|
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
This patch removes the crashkernel parsing from
arch/x86_64/kernel/machine_kexec.c and calls the generic function, introduced
in the last patch, in setup_bootmem_allocator().
This is necessary because the amount of System RAM must be known in this
function now because of the new syntax.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes the crashkernel parsing from
arch/i386/kernel/machine_kexec.c and calls the generic function, introduced in
the last patch, in setup_bootmem_allocator().
This is necessary because the amount of System RAM must be known in this
function now because of the new syntax.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
copy_oldmem_page should not return leaving a page frame from the
previous kernel mapped.
Signed-off-by: Fernando Luis Vázquez Cao <fernando@oss.ntt.co.jp>
Acked-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cpu_data is currently an array defined using NR_CPUS. This means that
we overallocate since we will rarely really use maximum configured cpus.
When NR_CPU count is raised to 4096 the size of cpu_data becomes
3,145,728 bytes.
These changes were adopted from the sparc64 (and ia64) code. An
additional field was added to cpuinfo_x86 to be a non-ambiguous cpu
index. This corresponds to the index into a cpumask_t as well as the
per_cpu index. It's used in various places like show_cpuinfo().
cpu_data is defined to be the boot_cpu_data structure for the NON-SMP
case.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Here is a small patch to change the behavior of the PMU msr allocator
to avoid BUG_ON() when the MSR is unknwon. Instead, it now returns
ok, which means "I do not manage". The current allocator is not
yet managing the full set of PMU registers (e.g., GLOBAL_* on Core 2).
[watchdog] do not BUG_ON() in the MSR allocator if MSR is unknown, return ok
instead
Signed-off-by: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This is from an earlier message from Christoph Lameter:
processor_core.c currently tries to determine the apicid by special casing
for IA64 and x86. The desired information is readily available via
cpu_physical_id()
on IA64, i386 and x86_64.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Additionally, boot_cpu_id needed to be exported to fix compile errors in
dma code when !CONFIG_SMP.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Convert cpu_llc_id from a static array sized by NR_CPUS to a per_cpu
variable. This saves sizeof(cpu_llc_id) * NR unused cpus. Access is
mostly from startup and CPU HOTPLUG functions.
Note there's an additional change of the type of cpu_llc_id from int to
u8 for ARCH i386 to correspond with the same type in ARCH x86_64.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch converts the x86_cpu_to_apicid array to be a per cpu
variable. This saves sizeof(apicid) * NR unused cpus. Access is mostly
from startup and CPU HOTPLUG functions.
MP_processor_info() is one of the functions that require access to the
x86_cpu_to_apicid array before the per_cpu data area is setup. For this
case, a pointer to the __initdata array is initialized in setup_arch()
and removed in smp_prepare_cpus() after the per_cpu data area is
initialized.
A second change is included to change the initial array value of ARCH
i386 from 0xff to BAD_APICID to be consistent with ARCH x86_64.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This simplifies the io_apic.c __assign_irq_vector() logic and removes
the explicit SYSCALL_VECTOR check, and also allows for vectors to be
reserved by other mechanisms (ie. lguest).
[ tglx: arch/x86 adaptation ]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Don't want any lockdep or other fragile machinery to run during oopses.
Use raw spinlocks directly for oops locking.
Also disables irq flag tracing there.
[ tglx: arch/x86 adaptation ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Do cpuid_device_create() in CPU_UP_PREPARE instead of CPU_ONLINE.
[ tglx: arch/x86 adaptation ]
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch defines the missing function smp_call_function_mask() for x86_64,
this is more or less a cut&paste of i386 function. It removes also some
duplicate code.
This function is needed by KVM to execute a function on some CPUs.
AK: Fixed description
AK: Moved WARN_ON(irqs_disabled) one level up to not warn in the panic case.
[ tglx: arch/x86 adaptation ]
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch provides a new set of functions for managing the descriptor
tables that can be used instead of putting the raw assembly in .c files.
Remodeling of store_tr() suggested by Frederik Deweerdt.
[ tglx: arch/x86 adaptation ]
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Both functions printk the same information, except for CRx and
debug registers in the show_registers() one and a bit different
manner. So move the common code into one place. This is already
done for x86_64, so I think it's worth having the same on i386.
This saves 100 bytes of .rodata section :) ...
but only 8 from .text :(
[ tglx: arch/x86 adaptation ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
[ tglx: arch/x86 adaptation ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
They were already very similar; just use the same file now.
[ tglx: arch/x86 adaptation ]
Cc: lenb@kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
ICH3 and ICH4 have undocumented HPET capabilities. This patch enables
HPET for platforms based around these ICHs.
Tested on various ICH3 and ICH4 platforms.
Because HPET is not officially documented for ICH3/4 and may not have
been validated by chipset folks, we're on thin ice here. I'd recommend
testing this patch in -hrt or -mm for a while and wait for
success/failure reports before feeding it upstream.
tglx: depends on the force_hpet command line option !
Signed-off-by: Udo A. Steinberg <us15@os.inf.tu-dresden.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch adds quirks to force enable HPET on Via VT8235 and
VT8237 chipsets. The datasheet for 8237 documents HPET
functionality (although wrongly) whereas HPET is undocumented
for 8235.
Tested on A7V880 (8237) and K7VT4A+ (8235) boards.
tglx: depends on the force_hept commandline option
Signed-off-by: Udo A. Steinberg <us15@os.inf.tu-dresden.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
add force_hpet boot option.
(this will be useful to make the forced-enable quirks depend on.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge init_task_32/64.c.
Move 64bit per cpu data orig_ist to setup64.c.
[ mingo: fixed checkpatch trivialities. ]
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Move the 64bit Kconfig file to arch/x86/kernel/cpu/cpufreq, so we
can unify them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Simple cosmetic update for the cs5536 reboot fixup; define the MSR that's used
for rebooting in geode.h, and use the define.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
x86 NUMA kernels crash in the scheduler setup code if "nosmp" or
"maxcpus=0" is passed on the boot command line:
| Brought up 1 CPUs
| BUG: unable to handle kernel NULL pointer dereference at virtual address 00000000
| printing eip: c011f0b5 *pde = 00000000
| Oops: 0000 [#1] SMP
|
| Pid: 1, comm: swapper Not tainted (2.6.23 #67)
| EIP: 0060:[<c011f0b5>] EFLAGS: 00010246 CPU: 0
| EIP is at sd_degenerate+0x35/0x40
the reason is sloppy spaghetti code in smpboot_32.c that resulted in a
missing map_cpu_to_logical_apicid() call - which also had the side-effect
of setting up the cpu_2_node[] entry for the lone CPU. That resulted in
node_to_cpumask(0) resulting in 00000000 - confusing the sched-domains
setup code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Appended patch fixes an oops while changing the vsyscall sysctl.
I am sure no one tested this code before integrating into mainline :(
BTW, using ioremap() in vsyscall_sysctl_change() to get the virtual
address of a kernel symbol sounds like an over kill.. I wonder if we
can define a simple __va_vsymbol() which will return directly the
kernel direct mapping. comments in the code which says gcc has trouble
with __va(__pa()) sounds bogus to me. __pa() on a vsyscall address will
not work anyhow :(
And also, the whole nop out syscall in vsyscall page infrastructure
(vsyscall_sysctl_change()) is added to make some attacks difficult,
and yet I don't see this nop out being done by default. This area
requires more cleanups?
Fix an oops with __pa_vsymbol(). VSYSCALL_FIRST_PAGE is a fixmap index.
We want the starting virtual address of the vsyscall page and not the index.
[ mingo: arch/x86 adaptation ]
Reported-by: Yanmin Zhang <yanmin.zhang@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Get rid of sparse related warnings from places that use integer as NULL
pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
msr_class_cpu_callback() can be marked __cpuinit, being the notifier callback
for a __cpuinitdata notifier_block. So can be marked msr_device_create() too,
called only from the newly-__cpuinit msr_class_cpu_callback() or from
__init-marked msr_init().
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Cc: Andi Kleen <ak@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
