| Age | Commit message (Collapse) | Author |
|---|
|
The current code to set up the GART as an IOMMU enables GART
translations before it removes the aperture from the kernel memory
map, sets the GART PTEs to UC, sets up the guard and scratch
pages, or does a wbinvd(). This leaves the possibility of cache
aliasing open and can cause system crashes.
Re-order the code so as to enable the GART translations only
after all safeguards are in place and the tlb has been flushed.
AMD has tested this patch on both Istanbul systems and 1st
generation Opteron systems with APG enabled and seen no adverse
effects. Istanbul systems with HT Assist enabled sometimes
see MCE errors due to cache artifacts with the unmodified
code.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Cc: <stable@kernel.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: akpm@linux-foundation.org
Cc: jbarnes@virtuousgeek.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
'amd-iommu/suspend-resume' and 'amd-iommu/extended-allocator' into amd-iommu/2.6.31
Conflicts:
arch/x86/kernel/amd_iommu.c
arch/x86/kernel/amd_iommu_init.c
|
|
This will test the automatic aperture enlargement code. This is
important because only very few devices will ever trigger this code
path. So force it under CONFIG_IOMMU_STRESS.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This forces testing of on-demand page table allocation code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Disabling the round-robin allocator results in reusing the same
dma-addresses again very fast. This is a good test if the iotlb flushing
is working correctly.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This parameter is not longer necessary when aperture increases
dynamically.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
By dynamically increasing the aperture the extended allocator is now
ready for use.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch makes sure no reserved addresses are allocated in an dma_ops
domain when the aperture is increased dynamically.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch prepares the dynamic increasement of dma_ops domain
apertures.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Simplify the code a little bit by using the same unit for all address
space related state in the dma_ops domain structure.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch changes the AMD IOMMU address allocator to allow up to 32
aperture ranges per dma_ops domain.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
The code will be required when the aperture size increases dynamically
in the extended address allocator.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch makes page table allocation usable for dma_ops code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This is a preperation for extended address allocator.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch puts everything together and enables suspend/resume support
in the AMD IOMMU driver.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch makes sure that no function required for suspend/resume of
AMD IOMMU driver is thrown away after boot.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This function is required for suspend/resume support with AMD IOMMU
enabled.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This function is required for suspend/resume support with AMD IOMMU
enabled.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This function is required for suspend/resume support with AMD IOMMU
enabled.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Current hardware uses msi instead of msi-x so this code it not necessary
and can not be tested. The best thing is to drop this code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
It is not necessary to loop again over all IOMMUs in this code. So drop
the loop.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch restructures the AMD IOMMU initialization code to initialize
all hardware registers with one single function call.
This is helpful for suspend/resume support.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch introduces the for_each_iommu and for_each_iommu_safe macros
to simplify the developers life when having to iterate over all AMD
IOMMUs in the system.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Some drivers may use the dma api during ->remove which will
cause a protection domain to get reattached to a device. Delay the
detach until after the driver is completely unbound.
[ joro: added a little merge helper ]
[ Impact: fix too early device<->domain removal ]
Signed-off-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
The bug never triggered. But it should be fixed to protect against
broken ACPI tables in the future.
[ Impact: protect against broken ivrs acpi table ]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
The devid parameter to set_dev_entry_from_acpi is the requester ID
rather than the device ID since it is used to index the IOMMU device
table. The handling of IVHD_DEV_ALIAS used to pass the device ID.
This patch fixes it to pass the requester ID.
[ Impact: fix setting the wrong req-id in acpi-table parsing ]
Signed-off-by: Neil Turton <nturton@solarflare.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
The variable amd_iommu_last_bdf holds the maximum bdf of any device
controlled by an IOMMU, so the number of device entries needed is
amd_iommu_last_bdf+1. The function tbl_size used amd_iommu_last_bdf
instead. This would be a problem if the last device were a large
enough power of 2.
[ Impact: fix amd_iommu_last_bdf off-by-one error ]
Signed-off-by: Neil Turton <nturton@solarflare.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
With device isolation disabled we can test better for race conditions in
dma_ops related code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This Kconfig option is intended to enable various code paths or
parameters in IOMMU implementations to stress test the code and/or the
hardware. This can also be done by disabling optimizations in the code
when this option is switched on.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
|
|
This information is only helpful for debugging. Don't print it anymore
unless explicitly requested.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Add information about device memory mapping requirements for the IOMMU
as described in the IVRS ACPI table to the kernel log if amd_iommu_dump
was specified on the kernel command line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Add information about devices belonging to an IOMMU as described in the
IVRS ACPI table to the kernel log if amd_iommu_dump was specified on the
kernel command line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Add information about IOMMU devices described in the IVRS ACPI table to
the kernel log if amd_iommu_dump was specified on the kernel command
line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This kernel parameter will be useful to get some AMD IOMMU related
information in dmesg that is not necessary for the default user but may
be helpful in debug situations.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Merge reason: core/iommu was on an .30-rc1 base,
update it to .30-rc5 to refresh.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: MCE: make cmci_discover_lock irq-safe
x86: xen, i386: reserve Xen pagetables
x86, kexec: fix crashdump panic with CONFIG_KEXEC_JUMP
x86-64: finish cleanup_highmaps()'s job wrt. _brk_end
x86: fix boot hang in early_reserve_e820()
x86: Fix a typo in a printk message
x86, srat: do not register nodes beyond e820 map
|
|
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix return value for sys_ipc
microblaze: Storage class should be before const qualifier
|
|
Lockdep reports the warning below when Li tries to offline one cpu:
[ 110.835487] =================================
[ 110.835616] [ INFO: inconsistent lock state ]
[ 110.835688] 2.6.30-rc4-00336-g8c9ed89 #52
[ 110.835757] ---------------------------------
[ 110.835828] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[ 110.835908] swapper/0 [HC1[1]:SC0[0]:HE0:SE1] takes:
[ 110.835982] (cmci_discover_lock){?.+...}, at: [<ffffffff80236dc0>] cmci_clear+0x30/0x9b
cmci_clear() can be called via smp_call_function_single().
It is better to disable interrupt while holding cmci_discover_lock,
to turn it into an irq-safe lock - we can deadlock otherwise.
[ Impact: fix possible deadlock in the MCE code ]
Reported-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A03ED38.8000700@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Shaohua Li<shaohua.li@intel.com>
|
|
The Xen pagetables are no longer implicitly reserved as part of the other
i386_start_kernel reservations, so make sure we explicitly reserve them.
This prevents them from being released into the general kernel free page
pool and reused.
[ Impact: fix Xen guest crash ]
Also-Bisected-by: Bryan Donlan <bdonlan@gmail.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4A032EEC.30509@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Tim Starling reported that crashdump will panic with kernel compiled
with CONFIG_KEXEC_JUMP due to null pointer deference in
machine_kexec_32.c: machine_kexec(), when deferencing
kexec_image. Refering to:
http://bugzilla.kernel.org/show_bug.cgi?id=13265
This patch fixes the BUG via replacing global variable reference:
kexec_image in machine_kexec() with local variable reference: image,
which is more appropriate, and will not be null.
Same BUG is in machine_kexec_64.c too, so fixed too in the same way.
[ Impact: fix crash on kexec ]
Reported-by: Tim Starling <tstarling@wikimedia.org>
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1241751101.6259.85.camel@yhuang-dev.sh.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
With the introduction of the .brk section, special care must be taken
that no unused page table entries remain if _brk_end and _end are
separated by a 2M page boundary. cleanup_highmap() runs very early and
hence cannot take care of that, hence potential entries needing to be
removed past _brk_end must be cleared once the brk allocator has done
its job.
[ Impact: avoids undesirable TLB aliases ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
If the first non-reserved (sub-)range doesn't fit the size requested,
an endless loop will be entered. If a range returned from
find_e820_area_size() turns out insufficient in size, the range must
be skipped before calling the function again.
[ Impact: fixes boot hang on some platforms ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5507/1: support R_ARM_MOVW_ABS_NC and MOVT_ABS relocation types
[ARM] 5506/1: davinci: DMA_32BIT_MASK --> DMA_BIT_MASK(32)
i.MX31: Disable CPU_32v6K in mx3_defconfig.
mx3fb: Fix compilation with CONFIG_PM
mx27ads: move PBC mapping out of vmalloc space
MXC: remove BUG_ON in interrupt handler
mx31: remove mx31moboard_defconfig
ARM: ARCH_MXC should select HAVE_CLK
mxc : BUG in imx_dma_request
mxc : Clean up properly when imx_dma_free() used without imx_dma_disable()
[ARM] mv78xx0: update defconfig
[ARM] orion5x: update defconfig
[ARM] Kirkwood: update defconfig
[ARM] Kconfig typo fix: "PXA930" -> "CPU_PXA930".
[ARM] S3C2412: Add missing cache flush in suspend code
[ARM] S3C: Add UDIVSLOT support for newer UARTS
[ARM] S3C64XX: Add S3C64XX_PA_IIS{0,1} to <mach/map.h>
|
|
From: Bruce Ashfield <bruce.ashfield@windriver.com>
To fully support the armv7-a instruction set/optimizations, support
for the R_ARM_MOVW_ABS_NC and R_ARM_MOVT_ABS relocation types is
required.
The MOVW and MOVT are both load-immediate instructions, MOVW loads 16
bits into the bottom half of a register, and MOVT loads 16 bits into the
top half of a register.
The relocation information for these instructions has a full 32 bit
value, plus an addend which is stored in the 16 immediate bits in the
instruction itself. The immediate bits in the instruction are not
contiguous (the register # splits it into a 4 bit and 12 bit value),
so the addend has to be extracted accordingly and added to the value.
The value is then split and put into the instruction; a MOVW uses the
bottom 16 bits of the value, and a MOVT uses the top 16 bits.
Signed-off-by: David Borman <david.borman@windriver.com>
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
As per commit 284901a90a9e0b812ca3f5f852cbbfb60d10249d, use
DMA_BIT_MASK(n)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
[ Impact: printk message cleanup ]
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
LKML-Reference: <200905040908.27299.knikanth@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The mem= option will truncate the memory map at a specified address so
it's not possible to register nodes with memory beyond the e820 upper
bound.
unparse_node() is only called when then node had memory associated with
it, although with the mem= option it is no longer addressable.
[ Impact: fix boot hang on certain (large) systems ]
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <alpine.DEB.2.00.0905051248150.20021@chino.kir.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] xen_domu_defconfig: fix build issues/warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: x86, mmiotrace: fix range test
tracing: fix ref count in splice pages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: show number of core_siblings instead of thread_siblings in /proc/cpuinfo
amd-iommu: fix iommu flag masks
x86: initialize io_bitmap_base on 32bit
x86: gettimeofday() vDSO: fix segfault when tv == NULL
|
