| Age | Commit message (Collapse) | Author |
|---|
|
|
|
not compiled in
|
|
* enable MFD_GLAMO_MCI for booting from SD
* enable touchscreen driver
* enable touchscreen filters
* enable /proc/config.gz
* drop gta01 support
* enable wm8753 (Kconfig option renamed)
* enable S3C24XX_ADC for touchscreen
|
|
This adds support for platform_battery driver which allows to specify a set
of power supply properties and callbacks to acquire them. It is needed to
support dumb batteries where all the information about their status can
only be obtained by platform-specific actions such as specific ADC
measurements, some guessimation etc.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
|
|
|
|
|
|
This is nonportable and wastes a lot of memory and thus should be replaced with
a prober solution asap.
|
|
pwm.
|
|
|
|
om-gta02-2.6.31
|
|
|
|
|
|
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
|
|
|
|
|
|
On Sat, Oct 24, 2009 at 3:04 AM, Nelson Castillo
<arhuaco@freaks-unidos.net> wrote:
> Hi there. I finally made this work. I tested with: cat /dev/input/touchscreen0 | hexdump
>
> I wonder why it didn't work with X... This rootfs works with other drivers I've tested (even with the upstream kernel).
Problem found.
Patch attached.
From: Nelson Castillo <arhuaco@freaks-unidos.net>
Date: Sat, 24 Oct 2009 14:12:58 -0500
Subject: [PATCH] Add auto-pst
Without these lines the TS doesn't work.
I didn't check who the author of the lines is.
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
|
|
This patch fixes a bug where the TS might stop working after suspend/resume.
This patch is under upstream review and it seems it will change a lot.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
|
|
Add the ts and the relevant files.
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
|
|
Without this patch we cannot make the s3c2410/s3c2440 touchscreen
driver work. This will be done in a different way in upstream kernel.
We specify the delay value (S3C2410_ADCDLY).
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
|
|
|
|
|
|
This patch adds a flag to the s3c2410_nand platform data, which configures
whether hardware ecc is used for that chip.
Currently hardware ecc is used if it was compiled into the kernel. But if you
want to build a kernel which runs on multiple devices you might have a
configuration where you have devices which require hw ecc as well as devices
which want software ecc.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
Early verions off uboot used for the gta02 flashed the nand with ecc information
incompatible to s3c2442 hardware ecc. Disable hardware error correction by
default, unless the bootloader explicitly enables it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
|
|
|
|
... and remove unused reset pin resource.
|
|
The gta02 uses the glamo mfd driver which requires 9 board irqs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
Some boards have a need for a set of extra IRQ numbers, for example some
multifunction devices which do irq demultiplexing require them.
This patch adds S3C2410_BOARD_NR_IRQS which specifies the number of extra board
IRQs. Board specific code would use S3C2410_BOARD_IRQ_START to get the number of
it's first irq.
Since it is possible to support a multiple boards with a single kernel and
there is no easy way to set a CONFIG option to multiple values and only use the
maximum each board which needs board IRQs has do be explicitly added to irqs.h
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
|
|
|
|
'glamo-2.6.31', 'jbt6k74-2.6.31', 'gta02-vibrator-2.6.31', 'bq27000-2.6.31', 'wm8753-2.6.31' and 'pcf50633-2.6.31' into om-gta02-2.6.31
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Add the S3C2442B CPU ID to aid support the Openmoko GTA02 / Freerunner.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: edit description for clarity and S3C2442B as uppercase]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
|
|
|
|
|
|
|
|
On hardware revision 5 and earlier the leds found on the gta02 are missing a
resistor and reading their gpio pin status will always return 0. So we have to
shadow the led states in software. This is done by "hijacking" the gpio accessor
functions for bank B.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
The gta02 has three leds which are connected though gpio pins and thus can get
supported by using the generic leds-gpio driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
The gta02 has two buttons which are connected to gpio pins and thus can get
supported by using the generic gpio-keys driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
|
|
This patch fixes a null pointer exception caused by removal of
'ack()' for level interrupts in the Xilinx interrupt driver. A recent
change to the xilinx interrupt controller removed the ack hook for
level irqs.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
