aboutsummaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2009-09-05[SCSI] zfcp: Remove duplicated code for debug timestampsChristof Schmitt
The timestamp calculation used for s390dbf output is the same in a private zfcp function and in debug.c. Replace both with a common inline function. Reviewed-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-08-21x86: don't call '->send_IPI_mask()' with an empty maskLinus Torvalds
As noted in 83d349f35e1ae72268c5104dbf9ab2ae635425d4 ("x86: don't send an IPI to the empty set of CPU's"), some APIC's will be very unhappy with an empty destination mask. That commit added a WARN_ON() for that case, and avoided the resulting problem, but didn't fix the underlying reason for why those empty mask cases happened. This fixes that, by checking the result of 'cpumask_andnot()' of the current CPU actually has any other CPU's left in the set of CPU's to be sent a TLB flush, and not calling down to the IPI code if the mask is empty. The reason this started happening at all is that we started passing just the CPU mask pointers around in commit 4595f9620 ("x86: change flush_tlb_others to take a const struct cpumask"), and when we did that, the cpumask was no longer thread-local. Before that commit, flush_tlb_mm() used to create it's own copy of 'mm->cpu_vm_mask' and pass that copy down to the low-level flush routines after having tested that it was not empty. But after changing it to just pass down the CPU mask pointer, the lower level TLB flush routines would now get a pointer to that 'mm->cpu_vm_mask', and that could still change - and become empty - after the test due to other CPU's having flushed their own TLB's. See http://bugzilla.kernel.org/show_bug.cgi?id=13933 for details. Tested-by: Thomas Björnell <thomas.bjornell@gmail.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-08-21x86: don't send an IPI to the empty set of CPU'sLinus Torvalds
The default_send_IPI_mask_logical() function uses the "flat" APIC mode to send an IPI to a set of CPU's at once, but if that set happens to be empty, some older local APIC's will apparently be rather unhappy. So just warn if a caller gives us an empty mask, and ignore it. This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86: change flush_tlb_others to take a const struct cpumask"), documented here: http://bugzilla.kernel.org/show_bug.cgi?id=13933 which causes a silent lock-up. It only seems to happen on PPro, P2, P3 and Athlon XP cores. Most developers sadly (or not so sadly, if you're a developer..) have more modern CPU's. Also, on x86-64 we don't use the flat APIC mode, so it would never trigger there even if the APIC didn't like sending an empty IPI mask. Reported-by: Pavel Vilim <wylda@volny.cz> Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com> Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de> Cc: Mike Travis <travis@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-08-19Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblazeLinus Torvalds
* 'next' of git://git.monstr.eu/linux-2.6-microblaze: microblaze: Update Microblaze defconfigs microblaze: Use klimit instead of _end for memory init microblaze: Enable ppoll syscall microblaze: Sane handling of missing timer/intc in device tree microblaze: use the generic ack_bad_irq implementation
2009-08-18Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: percpu: use the right flag for get_vm_area() percpu, sparc64: fix sparse possible cpu map handling init: set nr_cpu_ids before setup_per_cpu_areas()
2009-08-18Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86, mce: Don't initialize MCEs on unknown CPUs x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.c x86, mce: therm_throt: Don't log redundant normality x86: Fix UV BAU destination subnode id
2009-08-18Merge branch 'sh/for-2.6.31' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6 * 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: sh: sh7724 ddr self-refresh changes sh: use in-soc KEYSC on se7724 sh: CMT suspend/resume sh: skip disabled LCDC channels
2009-08-18microblaze: Update Microblaze defconfigsMichal Simek
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-08-18microblaze: Use klimit instead of _end for memory initMichal Simek
For noMMU system when you use larger rootfs image there is problem with using _end label because we increase klimit but in memory initialization we use still _end which is wrong. Larger mtd rootfs was rewritten by init_bootmem_node. MMU kernel use static initialization where klimit is setup to _end. There is no any other hanling with klimit. Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-08-18microblaze: Enable ppoll syscallMichal Simek
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-08-18microblaze: Sane handling of missing timer/intc in device treeJohn Williams
This code path doesn't test any returned pointers for NULL, leading to a bad kernel page fault if there's no timer/intc found. Slightly better is to BUG(), but even better still would be a printk beforehand. Signed-off-by: John Williams <john.williams@petalogix.com> Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-08-18microblaze: use the generic ack_bad_irq implementationChristoph Hellwig
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-08-17Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: MIPS: Fix HPAGE_SIZE redefinition
2009-08-17Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: (37 commits) ARM: 5673/1: U300 fix initsection compile warning ARM: Fix broken highmem support mx31moboard: invert sdhc ro signal sense ARM: S3C24XX: Fix clkout mpx error ARM: S3C64XX: serial: Fix a typo in Kconfig IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changes OMAP3: RX51: Updated rx51_defconfig OMAP2/3: mmc-twl4030: Free up MMC regulators while cleaning up OMAP3: RX51: Define TWL4030 USB transceiver in board file OMAP3: Overo: Fix smsc911x platform device resource value OMAP3: Fix omap3 sram virtual addres overlap vmalloc space after increasing vmalloc size OMAP2/3: DMA errata correction OMAP: Fix testing of cpu defines for mach-omap1 OMAP3: Overo: add missing pen-down GPIO definition OMAP: GPIO: clear/restore level/edge detect settings on mask/unmask OMAP3: PM: Fix wrong sequence in suspend. OMAP: PM: CPUfreq: obey min/max settings of policy OMAP2/3/4: UART: allow in-order port traversal OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports OMAP3: Fixed crash bug with serial + suspend ...
2009-08-17MIPS: Fix HPAGE_SIZE redefinitionAtsushi Nemoto
This patch fixes warnings like this: CC fs/proc/meminfo.o In file included from /work/linux/include/linux/mmzone.h:20, from /work/linux/include/linux/gfp.h:4, from /work/linux/include/linux/mm.h:8, from /work/linux/fs/proc/meminfo.c:5: /work/linux/arch/mips/include/asm/page.h:36:1: warning: "HPAGE_SIZE" redefined In file included from /work/linux/fs/proc/meminfo.c:2: /work/linux/include/linux/hugetlb.h:107:1: warning: this is the location of the previous definition Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Acked-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-08-17x86, mce: Don't initialize MCEs on unknown CPUsIngo Molnar
An older test-box started hanging at the following point during bootup: [ 0.022996] Mount-cache hash table entries: 512 [ 0.024996] Initializing cgroup subsys debug [ 0.025996] Initializing cgroup subsys cpuacct [ 0.026995] Initializing cgroup subsys devices [ 0.027995] Initializing cgroup subsys freezer [ 0.028995] mce: CPU supports 5 MCE banks I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit machine check code on 32bit"), which utilizes the MCE code on 32-bit systems too. The problem is caused by this detail in my config: # CONFIG_CPU_SUP_INTEL is not set This disables the quirks in mce_cpu_quirks() but still enables MCE support - which then hangs due to the missing quirk workaround needed on this CPU: if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0) mce_banks[0].init = 0; The safe solution is to not initialize MCEs if we dont know on what CPU we are running (or if that CPU's support code got disabled in the config). Also be a bit more defensive on 32-bit systems: dont do a boot-time dump of pending MCEs not just on the specific system that we found a problem with (Pentium-M), but earlier ones as well. Now this problem is probably not common and disabling CPU support is rare - but still being more defensive in something we turned on for a wide range of CPUs is prudent. Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-17x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUsBartlomiej Zolnierkiewicz
On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog): MCE 0 HARDWARE ERROR. This is *NOT* a software problem! Please contact your hardware vendor CPU 0 BANK 1 MCG status: MCi status: Error overflow Uncorrected error Error enabled Processor context corrupt MCA: Data CACHE Level-1 UNKNOWN Error STATUS f200000000000195 MCGSTATUS 0 [ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error) and f200000000000115 (... READ Error). To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump content of STATUS MSR before it is cleared during initialization. ] Since the bogus MCE results in a kernel taint (which in turn disables lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs by default ("mce=bootlog" boot parameter can be be used to get the old behavior). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Reviewed-by: Andi Kleen <andi@firstfloor.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-16x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.cLeonardo Potenza
The function uv_acpi_madt_oem_check() has been marked __init, the struct apic_x2apic_uv_x has been marked __refdata. The aim is to address the following section mismatch messages: WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary() The variable apic_x2apic_uv_x references the function __cpuinit uv_wakeup_secondary() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary() The variable apic_x2apic_uv_x references the function __cpuinit uv_wakeup_secondary() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap() The function uv_acpi_madt_oem_check() references the function __init early_ioremap(). This is often because uv_acpi_madt_oem_check lacks a __init annotation or the annotation of early_ioremap is wrong. WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap() The function uv_acpi_madt_oem_check() references the function __init early_iounmap(). This is often because uv_acpi_madt_oem_check lacks a __init annotation or the annotation of early_iounmap is wrong. WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary() The variable apic_x2apic_uv_x references the function __cpuinit uv_wakeup_secondary() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Leonardo Potenza <lpotenza@inwind.it> LKML-Reference: <200908161855.48302.lpotenza@inwind.it> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-16x86, mce: therm_throt: Don't log redundant normalityHugh Dickins
0d01f31439c1e4d602bf9fdc924ab66f407f5e38 "x86, mce: therm_throt - change when we print messages" removed redundant announcements of "Temperature/speed normal". They're not worth logging and remove their accompanying "Machine check events logged" messages as well from the console. Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk> Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dmitry Torokhov <dtor@mail.ru> LKML-Reference: <Pine.LNX.4.64.0908161544100.7929@sister.anvils> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-15ARM: 5673/1: U300 fix initsection compile warningLinus Walleij
The u300_init_check_chip() function was not properly tagged with the __init macro and provided a initsection mismatch on compilation. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-08-15Merge branch 's3c-fixes' of git://aeryn.fluff.org.uk/bjdooks/linuxRussell King
2009-08-15Merge branch 'for-rmk-rc' of git://git.pengutronix.de/git/imx/linux-2.6Russell King
2009-08-15ARM: Fix broken highmem supportRussell King
Currently, highmem is selectable, and you can request an increased vmalloc area. However, none of this has any effect on the memory layout since a patch in the highmem series was accidentally dropped. Moreover, even if you did want highmem, all memory would still be registered as lowmem, possibly resulting in overflow of the available virtual mapping space. The highmem boundary is determined by the highest allowed beginning of the vmalloc area, which depends on its configurable minimum size (see commit 60296c71f6c5063e3c1f1d2619ca0b60940162e7 for details on this). We should create mappings and initialize bootmem only for low memory, while the zone allocator must still be told about highmem. Currently, memory nodes which are completely located in high memory are not supported. This is not a huge limitation since systems relying on highmem support are unlikely to have discontiguous memory with large holes. [ A similar patch was meant to be merged before commit 5f0fbf9ecaf3 and be available in Linux v2.6.30, however some git rebase screw-up of mine dropped the first commit of the series, and that goofage escaped testing somehow as well. -- Nico ] Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Nicolas Pitre <nico@marvell.com>
2009-08-15x86: Fix UV BAU destination subnode idCliff Wickman
The SGI UV Broadcast Assist Unit is used to send TLB shootdown messages to remote nodes of the system. The header of the message must contain the subnode id of the block in the receiving hub that handles such messages. It should always be 0x10, the id of the "LB" block. It had previously been documented as a "must be zero" field. Signed-off-by: Cliff Wickman <cpw@sgi.com> Acked-by: Jack Steiner <steiner@sgi.com> LKML-Reference: <E1Mc1x7-0005Ce-6t@eag09.americas.sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-15sh: sh7724 ddr self-refresh changesMagnus Damm
This patch updates the SuperH Mobile sleep assembly code with support for DBSC memory controller found in the sh7724 processor. Without this fix the memory hooked up to the sh7724 processor will never enter self-refresh mode before suspending to ram. The effect of this is that the memory contents most likeley will be lost upon resume which may or may not be what you want. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-15sh: use in-soc KEYSC on se7724Magnus Damm
This patch updates the Solution Engine 7724 board code to use in-SoC KEYSC resources for the keyboard platform device. Using the in-SoC key scan controller fixes a crash-during-resume issue. Without this patch the KEYSC hardware block located in the board specific FPGA is used together with an external IRQ which is routed through the FPGA and handled by some board specific demux code. This board specific FPGA interrupt code does not implement desc->set_wake() so the enable_irq_wake() call in the sh_keysc driver will fail at suspend-to-ram time and the disable_irq_wake() will bomb out when resuming. Changing the platform data to use the in-SoC KEYSC hardware makes the se7724 board support code less special which is a good thing. Also, the board specific KEYSC pin setup code selects in-SoC pin functions already which makes the current FPGA platform device data look like a typo. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-14mx31moboard: invert sdhc ro signal senseValentin Longchamp
Small confusion with our hardware engineer, the WP signal (RO) is active low on our boards, the signal has to inverted. This is a pretty straightforward patch, it could even go to -rc, but if not, then push it for 2.6.32. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-08-14percpu, sparc64: fix sparse possible cpu map handlingTejun Heo
percpu code has been assuming num_possible_cpus() == nr_cpu_ids which is incorrect if cpu_possible_map contains holes. This causes percpu code to access beyond allocated memories and vmalloc areas. On a sparc64 machine with cpus 0 and 2 (u60), this triggers the following warning or fails boot. WARNING: at /devel/tj/os/work/mm/vmalloc.c:106 vmap_page_range_noflush+0x1f0/0x240() Modules linked in: Call Trace: [00000000004b17d0] vmap_page_range_noflush+0x1f0/0x240 [00000000004b1840] map_vm_area+0x20/0x60 [00000000004b1950] __vmalloc_area_node+0xd0/0x160 [0000000000593434] deflate_init+0x14/0xe0 [0000000000583b94] __crypto_alloc_tfm+0xd4/0x1e0 [00000000005844f0] crypto_alloc_base+0x50/0xa0 [000000000058b898] alg_test_comp+0x18/0x80 [000000000058dad4] alg_test+0x54/0x180 [000000000058af00] cryptomgr_test+0x40/0x60 [0000000000473098] kthread+0x58/0x80 [000000000042b590] kernel_thread+0x30/0x60 [0000000000472fd0] kthreadd+0xf0/0x160 ---[ end trace 429b268a213317ba ]--- This patch fixes generic percpu functions and sparc64 setup_per_cpu_areas() so that they handle sparse cpu_possible_map properly. Please note that on x86, cpu_possible_map() doesn't contain holes and thus num_possible_cpus() == nr_cpu_ids and this patch doesn't cause any behavior difference. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: Ingo Molnar <mingo@elte.hu>
2009-08-14ARM: S3C24XX: Fix clkout mpx errorDavide Rizzo
Bug correction: CLK Outputs cannot have XTAL as parent Signed-off-by: Davide Rizzo <elpa.rizzo@gmail.com> [ben-linux@fluff.org: updated patch subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-08-13Merge branch 'perfcounters-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: perf_counter: Report the cloning task as parent on perf_counter_fork() perf_counter: Fix an ipi-deadlock perf: Rework/fix the whole read vs group stuff perf_counter: Fix swcounter context invariance perf report: Don't show unresolved DSOs and symbols when -S/-d is used perf tools: Add a general option to enable raw sample records perf tools: Add a per tracepoint counter attribute to get raw sample perf_counter: Provide hw_perf_counter_setup_online() APIs perf list: Fix large list output by using the pager perf_counter, x86: Fix/improve apic fallback perf record: Add missing -C option support for specifying profile cpu perf tools: Fix dso__new handle() to handle deleted DSOs perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available perf report: Show the tid too in -D perf record: Fix .tid and .pid fill-in when synthesizing events perf_counter, x86: Fix generic cache events on P6-mobile CPUs perf_counter, x86: Fix lapic printk message
2009-08-13Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86: Fix oops in identify_cpu() on CPUs without CPUID x86: Clear incorrectly forced X86_FEATURE_LAHF_LM flag x86, mce: therm_throt - change when we print messages x86: Add reboot quirk for every 5 series MacBook/Pro
2009-08-13Merge branch 'ixp4xx-fixes' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6
2009-08-13sh: fix i2c init order on ap325rxa V2Magnus Damm
Convert the AP325RXA board code to register devices at arch_initcall() time instead of device_initcall(). This fix unbreaks pcf8563 RTC driver support. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-13sh: fix i2c init order on Migo-R V2Magnus Damm
Convert the Migo-R board code to register devices at arch_initcall() time instead of __initcall(). This fix unbreaks migor_ts touch screen driver support. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-13sh: convert processor device setup functions to arch_initcall()Magnus Damm
Convert the processor platform device setup functions from __initcall() and sometimes device_initcall() to arch_initcall(). This makes sure that the platform devices are registered a bit earlier so the devices are available when drivers register using initcall levels earlier than device_initcall(). A good example is platform devices needed by i2c-sh_mobile.c which registers a bit earlier using subsys_initcall(). Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-12perf_counter, x86: Fix/improve apic fallbackIngo Molnar
Johannes Stezenbach reported that his Pentium-M based laptop does not have the local APIC enabled by default, and hence perfcounters do not get initialized. Add a fallback for this case: allow non-sampled counters and return with an error on sampled counters. This allows 'perf stat' to work out of box - and allows 'perf top' and 'perf record' to fall back on a hrtimer based sampling method. ( Passing 'lapic' on the boot line will allow hardware sampling to occur - but if the APIC is disabled permanently by the hardware then this fallback still allows more systems to use perfcounters. ) Also decouple perfcounter support from X86_LOCAL_APIC. -v2: fix typo breaking counters on all other systems ... Reported-by: Johannes Stezenbach <js@sig21.net> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> LKML-Reference: <new-submission> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-12x86: Fix oops in identify_cpu() on CPUs without CPUIDOndrej Zary
Kernel is broken for x86 CPUs without CPUID since 2.6.28. It crashes with NULL pointer dereference in identify_cpu(): 766 generic_identify(c); 767 768--> if (this_cpu->c_identify) 769 this_cpu->c_identify(c); this_cpu is NULL. This is because it's only initialized in get_cpu_vendor() function, which is not called if the CPU has no CPUID instruction. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> LKML-Reference: <200908112000.15993.linux@rainbow-software.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-11arch/ia64/kernel/iosapic: missing test after ioremap()Roel Kluin
Missing test after ioremap() Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Fenghua Yu <fenghua.yu@intel.com>
2009-08-11ia64/topology.c: exit cache_add_dev when kobject_init_and_add failsFenghua Yu
Make cache_add_dev exit sysfs when kobject_init_and_add returns an error. Signed-off-by: Xiaotian Feng <dfeng@redhat.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
2009-08-11arch/ia64/Makefile: Remove -mtune=merced in IA64 kernel buildFenghua Yu
Between GCC version 3.4.0 and 4.3.3 (including 3.4.0 and 4.3.3), -mtune=merced is implemented in GCC. Starting from 4.4.0, -mtune=merced is deprecated. Even implemented in versions between 3.4.0 and 4.3.3, the -mtune=merced feature has been broken in some of the versions. For example, GCC 4.1.2 reports interanl tuning function errors during kernel building with -mtune=merced. Or GCC Bugzilla 16130 reports another -mtune=merced issue on GCC 3.4.1. So I would remove the -mtune=merced from IA64 kernel build. Without this option, kernel on Merced will remain the same except losing an unstable and out-of-date performance tunning feature. Since GCC version 3.4.0, -mtune=mckinley has been implemented. The -mtune=mckinley option functions the same as mtune=itanium2. And mtune=itanium2 is the default option. So we don't need to add mtune=mckinley either since its been the default option in any GCC version which implements this option. Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
2009-08-11IA64: includecheck fix: ia64, pgtable.hJaswinder Singh Rajput
fix the following 'make includecheck' warning: arch/ia64/include/asm/pgtable.h: asm/processor.h is included more than once. Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Acked-by: Fenghua Yu <fenghua.yu@intel.com>
2009-08-11IA64: includecheck fix: ia64, ia64_ksyms.cJaswinder Singh Rajput
fix the following 'make includecheck' warning: arch/ia64/kernel/ia64_ksyms.c: asm/page.h is included more than once. Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Acked-by: Fenghua Yu <fenghua.yu@intel.com>
2009-08-11ia64: boolean __test_and_clear_bitJohannes Weiner
__test_and_clear_bit() returns a bitfield with the tested-for bit set. Make it consistent with the other bitops - of ia64 but also every other architecture - and return a boolean value. Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Fenghua Yu <fenghua.yu@intel.com>
2009-08-11Bug Fix arch/ia64/kernel/pci-dma.c: fix recursive dma_supported() call in ↵Fenghua Yu
iommu_dma_supported() In commit 160c1d8e40866edfeae7d68816b7005d70acf391, dma_ops->dma_supported = iommu_dma_supported; This dma_ops->dma_supported is first called in platform_dma_init() during kernel boot. Then dma_ops->dma_supported will be called recursively in iommu_dma_supported. Kernel can not boot because kernel can not get out of iommu_dma_supported until it runs out of stack memory. Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
2009-08-11IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changesMikael Pettersson
2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata driver doesn't find the PCI IDE controller any more. 2.6.30 was fine. I traced this to a PCI update (1f82de10d6b1d845155363c895c552e61b36b51a) in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and 2.6.30-git19 illustrates the breakage: > --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200 > +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200 > @@ -26,6 +26,13 @@ > pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot > pci 0000:00:02.2: PME# disabled > PCI: bus0: Fast back to back transfers disabled > +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff] > bio: create slab <bio-0> at 0 > SCSI subsystem initialized > NET: Registered protocol family 2 > @@ -44,11 +51,7 @@ > console [ttyS0] enabled > serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale > Driver 'sd' needs updating - please use bus_type methods > -PCI: enabling device 0000:00:01.0 (0140 -> 0141) > -scsi0 : pata_artop > -scsi1 : pata_artop > -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28 > -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28 > +pata_artop 0000:00:01.0: no available native port > Using configured DiskOnChip probe address 0x50000000 > DiskOnChip found at 0x50000000 > NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit) The specific change in 1f82de10d6b1d845155363c895c552e61b36b51a responsible for this failure turned out to be the following: > --- a/drivers/pci/probe.c > +++ b/drivers/pci/probe.c > @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type, > res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN; > if (type == pci_bar_io) { > l &= PCI_BASE_ADDRESS_IO_MASK; > - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff; > + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT; > } else { > l &= PCI_BASE_ADDRESS_MEM_MASK; > mask = (u32)PCI_BASE_ADDRESS_MEM_MASK; Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx defines it as 0xffff0000, which is now causing the PCI failures. Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT should be 0x0000ffff. This patch makes that change, which fixes the PCI failures on my ixp4xx box. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
2009-08-11x86: Clear incorrectly forced X86_FEATURE_LAHF_LM flagKevin Winchester
Due to an erratum with certain AMD Athlon 64 processors, the BIOS may need to force enable the LAHF_LM capability. Unfortunately, in at least one case, the BIOS does this even for processors that do not support the functionality. Add a specific check that will clear the feature bit for processors known not to support the LAHF/SAHF instructions. Signed-off-by: Kevin Winchester <kjwinchester@gmail.com> Acked-by: Borislav Petkov <petkovbb@googlemail.com> LKML-Reference: <4A80A5AD.2000209@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-11perf_counter, x86: Fix generic cache events on P6-mobile CPUsIngo Molnar
Johannes Stezenbach reported that 'perf stat' does not count cache-miss and cache-references events on his Pentium-M based laptop. This is because we left them blank in p6_perfmon_event_map[], fill them in. Reported-by: Johannes Stezenbach <js@sig21.net> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> LKML-Reference: <new-submission> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-11perf_counter, x86: Fix lapic printk messageIngo Molnar
Instead of this garbled bootup on UP Pentium-M systems: [ 0.015048] Performance Counters: [ 0.016004] no Local APIC, try rebooting with lapicno PMU driver, software counters only. Print: [ 0.015050] Performance Counters: [ 0.016004] no APIC, boot with the "lapic" boot parameter to force-enable it. [ 0.017003] no PMU driver, software counters only. Cf: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> LKML-Reference: <new-submission> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-11x86, mce: therm_throt - change when we print messagesDmitry Torokhov
My Latitude d630 seems to be handling thermal events in SMI by lowering the max frequency of the CPU till it cools down but still leaks the "everything is normal" events. This spams the console and with high priority printks. Adjust therm_throt driver to only print messages about the fact that temperatire returned back to normal when leaving the throttling state. Also lower the severity of "back to normal" message from KERN_CRIT to KERN_INFO. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Acked-by: H. Peter Anvin <hpa@zytor.com> LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-08-10x86: Add reboot quirk for every 5 series MacBook/ProShunichi Fuji
Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5) too. It seems all unibody MacBook and MacBookPro require PCI reboot handling, i guess. Following model/machine ID list shows unibody MacBook/Pro have the 5 series of model number: http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.html Signed-off-by: Shunichi Fuji <palglowr@gmail.com> Cc: Ozan Çağlayan <ozan@pardus.org.tr> LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>