| Age | Commit message (Collapse) | Author |
|---|
|
Currently the fsl,*lbc devices support 8 banks (ie OR and BR registers).
This is adequate for most pq2 and pq3 processors, but not the MPC8280 which
has 12 banks.
Signed-Off-By: Mark Ware <mware@elphinstone.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some MPC85xx platforms do support 4 ethernet ports, so make sure the boot
wrapper fixes up all of them in the fdt.
Since MAC addresses are at the end of the bd_t structure there is no harm
in expanding to support 4 MAC address on older 85xx systems that might not
have that many.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Currently the kernel expects the additional four IBAT and DBAT registers
to be available, but doesn't enable these registers on 745x CPUs, which
have them disabled after reset. Thus set the HIGH_BAT_EN bit in HID0
register, if the corresponding MMU feature is defined.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The PCIe MSI interrupts are missing from the device tree source, and
thus were not enabled. This patch adds them.
Tested to work on MPC8315E-RDB with custom FPGA PCIe device.
Signed-off-by: Leon Woestenberg <leon@sidebranch.com>
Tested-by: Leon Woestenberg <leon@sidebranch.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Mappings for temperature sensors (adt7461 and lm92) are missing from the
SBC610's DTS file.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
As of commit 404614728f857d0ac63d29c3a29d0cf392a15598 ("Update FSL
esdhc binding"), we use "fsl,esdhc" compatible entry as a base
match. U-Boot will use the same compatible to fixup esdhc nodes.
This patch updates 83xx dts files so that they conform to the new
bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some boot loaders may not enable L1 instruction/data cache. Check if
data and instruction caches are enabled, and enable them if needed.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The current device tree for the MPC8272ADS assumes a mapping of 32 MB
of NOR flash at 0xFE00.0000, while there are actually only 8 MB on
the boards, mapped at 0xFF80.0000. When booting an uImage with such a
device tree, the kernel crashes because 0xFE00.0000 is not mapped.
Also introduce aliases for serial[01] and ethernet[01].
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add the platform-specific code for enabling SWIOTLB if needed on P2020DS,
MPC85xx DS, and MPC85xx MDS boards as they are capable of having >4G of
memory.
We determine if we need to enable swiotlb based on how much memory is in
the board and if it exceeds 4G or what we can map via PCI inbound
windows.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This is the final bit of code to allow enabling swiotlb on
mpc86xx. The platform-specific code is very small and consists
of enabling SWIOTLB in the config file, registering the
swiotlb_setup_bus_notifier initcall, and setting pci_dma_ops
to point to swiotlb_pci_dma_ops if we have more memory than
can be mapped by the inbound PCI windows.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Currently the FLASH database is updated by the kernel using file operations,
meant for userspace only. While this works for us because copy_{from,to}_user()
on powerpc can handle kernel pointers, this is unportable and a bad example.
Replace the file operations by callbacks, registered by the ps3flash driver.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
They were never intended to be exported using EXPORT_SYMBOL() anyway
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
It reports the failure of a call to lv1_put_iopte(), not
lv1_map_device_dma_region().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This makes 32-bit powerpc use the generic atomic64_t implementation.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On 32-bit non-Book E, local_irq_restore() turns into just mtmsr(),
which doesn't currently have a compiler memory barrier. This means
that accesses to memory inside a local_irq_save/restore section,
or a spin_lock_irqsave/spin_unlock_irqrestore section on UP, can
be reordered by the compiler to occur outside that section.
To fix this, this adds a compiler memory barrier to mtmsr for both
32-bit and 64-bit. Having a compiler memory barrier in mtmsr makes
sense because it will almost always be changing something about the
context in which memory accesses are done, so in general we don't want
memory accesses getting moved from one side of an mtmsr to the other.
With the barrier in mtmsr(), some of the explicit barriers in
hw_irq.h are now redundant, so this removes them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
signal_vsp_instruction() is currently only used if CONFIG_PROC_FS
is enabled. However logically it has nothing to do with PROC_FS,
so rather than making it depend on that mark it as maybe unused.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If CONFIG_BLK_DEV_INITRD is unset dt_prop_u64() is unused, which
causes a warning. We don't really want to tie the definition to
BLK_DEV_INITRD, so mark it as maybe unused.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 28794d34 ("powerpc/kconfig: Kill PPC_MULTIPLATFORM"), added
CONFIG_PPC_OF_BOOT_TRAMPOLINE to control the buliding of prom_init.o
However the Makefile still unconditionally builds prom_init_check,
the script that checks prom_init.o for symbol usage, and so in turn
prom_init.o is still always being built. (it's not linked though)
So surround all the prom_init_check logic with an ifeq block testing
if CONFIG_PPC_OF_BOOT_TRAMPOLINE is set.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The Axon MSI driver incorrectly uses platform_data, rather than
the proper accessors for driver_data.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When CONFIG_RELOCATABLE is enabled, PHYSICAL_START is actually a
variable of type phys_addr_t. That means to print it we need to
cast to unsigned long long and use llx.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
During cleanup, use L1GPU_CONTEXT_ATTRIBUTE_FB_CLOSE to tear down the setup
done by L1GPU_CONTEXT_ATTRIBUTE_FB_SETUP.
This allows unloading and reloading of ps3fb while the sound driver keeps the
GPU open.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Cc: Jim Paris <jim@jtan.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Both arch/powerpc/platforms/cell/iommu.c and arch/powerpc/platforms/ps3/mm.c
contain the same Cell IOMMU page table entry definitions. Extract them and move
them to <asm/iommu.h>, while adding a CBE_ prefix.
This also allows them to be used by drivers.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently we are wasting time calling the generic calibrate_delay()
function. We don't need it since our implementation of __delay() is
based on the CPU timebase. So instead, we use our own small
implementation that initializes loops_per_jiffy to something sensible
to make the few users like spinlock debug be happy
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If anything goes wrong when copying images into the install path, then
the install script should exit with an error code so that 'make' knows
about it and tells the user.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6:
headers_check fix: mn10300, setup.h
headers_check fix: mn10300, ptrace.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (31 commits)
trivial: remove the trivial patch monkey's name from SubmittingPatches
trivial: Fix a typo in comment of addrconf_dad_start()
trivial: usb: fix missing space typo in doc
trivial: pci hotplug: adding __init/__exit macros to sgi_hotplug
trivial: Remove the hyphen from git commands
trivial: fix ETIMEOUT -> ETIMEDOUT typos
trivial: Kconfig: .ko is normally not included in module names
trivial: SubmittingPatches: fix typo
trivial: Documentation/dell_rbu.txt: fix typos
trivial: Fix Pavel's address in MAINTAINERS
trivial: ftrace:fix description of trace directory
trivial: unnecessary (void*) cast removal in sound/oss/msnd.c
trivial: input/misc: Fix typo in Kconfig
trivial: fix grammo in bus_for_each_dev() kerneldoc
trivial: rbtree.txt: fix rb_entry() parameters in sample code
trivial: spelling fix in ppc code comments
trivial: fix typo in bio_alloc kernel doc
trivial: Documentation/rbtree.txt: cleanup kerneldoc of rbtree.txt
trivial: Miscellaneous documentation typo fixes
trivial: fix typo milisecond/millisecond for documentation and source comments.
...
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5545/2: add flush_kernel_dcache_page() for ARM
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
|
|
Without this, the default implementation is a no op which is completely
wrong with a VIVT cache, and usage of sg_copy_buffer() produces
unpredictable results.
Tested-by: Sebastian Andrzej Siewior <bigeasy@breakpoint.cc>
CC: stable@kernel.org
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/Makefile
Updates:
arch/arm/mach-u300/core.c
arch/arm/mach-u300/timer.c
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel
|
|
|
|
fix the following 'make headers_check' warnings:
usr/include/asm-mn10300/setup.h:14: extern's make no sense in userspace
usr/include/asm-mn10300/setup.h:15: extern's make no sense in userspace
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
fix the following 'make headers_check' warning:
usr/include/asm-mn10300/ptrace.h:80: extern's make no sense in userspace
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
|
|
Fix interaction with new generic header stuff as added by:
commit 6103ec56c65c33774c7c38652c8204120c3c7519
Author: Arnd Bergmann <arnd@arndb.de>
Date: Wed May 13 22:56:27 2009 +0000
asm-generic: add generic ABI headers
The problem is that asm/signal.h has been made to include asm-generic/signal.h,
but the redundant stuff from asm/signal.h has not been discarded, leading to
multiple redefinitions.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (80 commits)
x86, mce: Add boot options for corrected errors
x86, mce: Fix mce printing
x86, mce: fix for mce counters
x86, mce: support action-optional machine checks
x86, mce: define MCE_VECTOR
x86, mce: rename mce_notify_user to mce_notify_irq
x86: fix panic with interrupts off (needed for MCE)
x86, mce: export MCE severities coverage via debugfs
x86, mce: implement new status bits
x86, mce: print header/footer only once for multiple MCEs
x86, mce: default to panic timeout for machine checks
x86, mce: improve mce_get_rip
x86, mce: make non Monarch panic message "Fatal machine check" too
x86, mce: switch x86 machine check handler to Monarch election.
x86, mce: implement panic synchronization
x86, mce: implement bootstrapping for machine check wakeups
x86, mce: check early in exception handler if panic is needed
x86, mce: add table driven machine check grading
x86, mce: remove TSC print heuristic
x86, mce: log corrected errors when panicing
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (35 commits)
hwrng: timeriomem - Fix potential oops (request_mem_region/__devinit)
crypto: api - Use formatting of module name
crypto: testmgr - Allow hash test vectors longer than a page
crypto: testmgr - Check all test vector lengths
crypto: hifn_795x - fix __dev{init,exit} markings
crypto: tcrypt - Do not exit on success in fips mode
crypto: compress - Return produced bytes in crypto_{,de}compress_{update,final}
hwrng: via_rng - Support VIA Nano hardware RNG on X86_64 builds
hwrng: via_rng - Support VIA Nano hardware RNG
hwrng: via_rng - The VIA Hardware RNG driver is for the CPU, not Chipset
crypto: testmgr - Skip algs not flagged fips_allowed in fips mode
crypto: testmgr - Mark algs allowed in fips mode
crypto: testmgr - Add ctr(aes) test vectors
crypto: testmgr - Dynamically allocate xbuf and axbuf
crypto: testmgr - Print self-test pass notices in fips mode
crypto: testmgr - Catch base cipher self-test failures in fips mode
crypto: testmgr - Add ansi_cprng test vectors
crypto: testmgr - Add infrastructure for ansi_cprng self-tests
crypto: testmgr - Add self-tests for rfc4309(ccm(aes))
crypto: testmgr - Handle AEAD test vectors expected to fail verification
...
|
|
The unaligned address exception handler (and others) does not scan the
fixup tables before oopsing. This is bad because it means passing a
badly aligned pointer from user space might crash the kernel.
Fix this by scanning the fixup tables in _exception(). This should
resolve the issue for unaligned addresses as well as other less common
exceptions that might be happening during a userspace access. The page
fault handler already does fixup processing.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
add generic lib/checksum.c
asm-generic: add a generic uaccess.h
asm-generic: add generic NOMMU versions of some headers
asm-generic: add generic atomic.h and io.h
asm-generic: add legacy I/O header files
asm-generic: add generic versions of common headers
asm-generic: make bitops.h usable
asm-generic: make pci.h usable directly
asm-generic: make get_rtc_time overridable
asm-generic: rename page.h and uaccess.h
asm-generic: rename atomic.h to atomic-long.h
asm-generic: add a generic unistd.h
asm-generic: add generic ABI headers
asm-generic: add generic sysv ipc headers
asm-generic: introduce asm/bitsperlong.h
asm-generic: rename termios.h, signal.h and mman.h
|
