| Age | Commit message (Collapse) | Author |
|---|
|
Kill MN10300's own profiling Kconfig as this is superfluous given that the
profiling options have moved to init/Kconfig and arch/Kconfig. Not only is
this now superfluous, but the dependencies are not correct.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_debug remove execute permission
x86: smarten /proc/interrupts output for new counters
x86: DMI match for the Dell DXP061 as it needs BIOS reboot
x86: make 64 bit to use default_inquire_remote_apic
x86, setup: un-resequence mode setting for VGA 80x34 and 80x60 modes
x86, intel-iommu: fix X2APIC && !ACPI build failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: consolidate documents
blktrace: pass the right pointer to kfree()
tracing/syscalls: use a dedicated file header
tracing: append a comma to INIT_FTRACE_GRAPH
|
|
Convert the last remaining users to no_irq_chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It seems by mistake these files got execute permissions so removing it.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
LKML-Reference: <1239211186.9037.2.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix build warnings and possibe compat misbehavior on IA64
Building a kernel on ia64 might trigger these ugly build warnings:
CC arch/ia64/ia32/sys_ia32.o
In file included from arch/ia64/ia32/sys_ia32.c:55:
arch/ia64/ia32/ia32priv.h:290:1: warning: "elf_check_arch" redefined
In file included from include/linux/elf.h:7,
from include/linux/module.h:14,
from include/linux/ftrace.h:8,
from include/linux/syscalls.h:68,
from arch/ia64/ia32/sys_ia32.c:18:
arch/ia64/include/asm/elf.h:19:1: warning: this is the location of the previous definition
[...]
sys_ia32.c includes linux/syscalls.h which in turn includes linux/ftrace.h
to import the syscalls tracing prototypes.
But including ftrace.h can pull too much things for a low level file,
especially on ia64 where the ia32 private headers conflict with higher
level headers.
Now we isolate the syscall tracing headers in their own lightweight file.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jason Baron <jbaron@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Michael Davidson <md@google.com>
LKML-Reference: <20090408184058.GB6017@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Hook up sys_preadv and sys_pwritev
sparc64: add_node_ranges() must be __init
serial: sunsu: sunsu_kbd_ms_init needs to be __devinit
sparc: Fix section mismatch warnings in cs4231 sound driver.
sparc64: Fix section mismatch warnings in PCI controller drivers.
sparc64: Fix section mismatch warnings in power driver.
sparc64: get_cells() can't be marked __init
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] wire up preadv/pwritev system calls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
x86 ACPI: Add support for Always Running APIC timer
ACPI x86: Make aperf/mperf MSR access in acpi_cpufreq read_only
ACPI x86: Cleanup acpi_cpufreq structures related to aperf/mperf
ACPICA: delete check for AML access to port 0x81-83
ACPI: WMI: use .notify method instead of installing handler directly
sony-laptop: use .notify method instead of installing handler directly
panasonic-laptop: use .notify method instead of installing handler directly
fujitsu-laptop: use .notify method instead of installing hotkey handler directly
fujitsu-laptop: use .notify method instead of installing handler directly
ACPI: video: use .notify method instead of installing handler directly
ACPI: thermal: use .notify method instead of installing handler directly
ACPI battery: fix async boot oops
ACPI: delete acpi_device.g_list
NULL noise: drivers/platform/x86/panasonic-laptop.c
ACPI: cpufreq: remove dupilcated #include
ACPI: Adjust Kelvin offset to match local implementation
ACPI: convert acpi_device_lock spinlock to mutex
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5446/1: ohci-at91: Limit vbus_pin assignment to the size of the array
[ARM] 5445/1: AT91: Remove flexible array from USBH platform data
[ARM] 5447/1: Add SZ_32K
[ARM] omap: fix omap1 clock usecount decrement bug
[ARM] pxa: register AC97 controller devices
[ARM] pxa/csb701: do not register devices on non-csb726 boads
[ARM] pxa/colibri: get rid of set_irq_type()
[ARM] pxa/colibri: provide MAC address from ATAG_SERIAL
[ARM] pxa/cm-x2xx: fix ucb1400 not being registered
[ARM] pxa: Add support for suspend on PalmTX, T5 and LD
[ARM] pxa: PalmTE2 support for battery, UDC, IrDA and backlight
[ARM] pxa: Palm Tungsten E2 basic support
[ARM] pxa/em-x270: add libertas device registration
[ARM] pxa/magician: Enable bq24022 regulator for gpio_vbus and pda_power
|
|
Gerd Hoffmann added these to Linux. Let ia64 use them.
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The flexible array in the USBH platform data is not safe to copy. The
compiler will not allocate any extra memory for the non-init platform
data structure (in the *_devices.c files) since it isn't given any
defaults at compile time. When the probe function attempts to address
that array, it will actually attempt to access data in an adjacent
structure.
Since there are currently no (known) implementations of the at91 USBH
IP with more than 2 vbus pins, I am capping the value at 2. If somebody
tries to assign more, then the compiler will produce a warning.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds a SZ_32K define to the available sizes. I need it for an
upcoming platform support.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Now /proc/interrupts of tip tree has new counters:
PLT: Platform interrupts
Format change of output, as like that by commit:
commit 7a81d9a7da03d2f27840d659f97ef140d032f609
x86: smarten /proc/interrupts output
should be applied to these new counters too.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49C98DEA.8060208@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: fix to be queued up depends on upstream facilities
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Closes http://bugzilla.kernel.org/show_bug.cgi?12901
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
LKML-Reference: <20090326204524.4454.8776.stgit@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: restore old behavior
for flat and phys_flat
Signed-off-by: Yinhai Lu <yinghai@kernel.org.
LKML-Reference: <49DCBBF1.8080903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
and 'bjorn.notify' into release
|
|
Add support for Always Running APIC timer, CPUID_0x6_EAX_Bit2.
This bit means the APIC timer continues to run even when CPU is
in deep C-states.
The advantage is that we can use LAPIC timer on these CPUs
always, and there is no need for "slow to read and program"
external timers (HPET/PIT) and the timer broadcast logic
and related code in C-state entry and exit.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Do not write zeroes to APERF and MPERF by ondemand governor. With this
change, other users can share these MSRs for reads.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Change structure name to make the code cleaner and simpler. No
functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
branch tracer: Fix for enabling branch profiling makes sparse unusable
ftrace: Correct a text align for event format output
Update /debug/tracing/README
tracing/ftrace: alloc the started cpumask for the trace file
tracing, x86: remove duplicated #include
ftrace: Add check of sched_stopped for probe_sched_wakeup
function-graph: add proper initialization for init task
tracing/ftrace: fix missing include string.h
tracing: fix incorrect return type of ns2usecs()
tracing: remove CALLER_ADDR2 from wakeup tracer
blktrace: fix pdu_len when tracing packet command requests
blktrace: small cleanup in blk_msg_write()
blktrace: NUL-terminate user space messages
tracing: move scripts/trace/power.pl to scripts/tracing/power.pl
|
|
Impact: Fixes these modes on at least one system
The rewrite of the setup code into C resequenced the font setting and
register reprogramming phases of configuring nonstandard VGA modes
which use 480 scan lines in text mode. However, there exists at least
one board (Micro-Star MS-7383 version 2.0) on which this resequencing
causes an unusable display.
Revert to the original sequencing: set up 480-line mode, install the
font, and then adjust the vertical end register appropriately.
This failure was masked by the fact that the 480-line setup was broken
until checkin 5f641356127712fbdce0eee120e5ce115860c17f (therefore this
is not a -stable candidate bug fix.)
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
|
|
Both software emulated and hardware based CTS and RTS are enabled in
serial driver.
The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device. In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Only the CTS bit is affected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the new general RS485 Linux data structure (introduced by Alan with
commit number c26c56c0f40e200e61d1390629c806f6adaffbcc) in the Cris
architecture too (currently, Cris still uses the old private data
structure instead of the new one).
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Tested-by: Janez Cufer <janez.cufer@cetrtapot.si>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
1. Rewrite of the non-dma data transfer functions to use only ONE mode
of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX
bit pattern. So the TDBR = 0xFFFF inside the read calls won't work.
2. Clear SPI_RDBR before reading and before duplex transfer.
Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a
lot of duplex transfers, this is the main cause of mmc_spi failure.
3. Poll RXS for transfer completion. Polling SPIF or TXS cannot
guarantee transfer completion. This may interrupt a transfer before it
is finished. Also this may leave garbage data in buffer and affect
next transfer.
[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for GPIO controlled SPI Chip Selects. To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.
struct spi_board_info
.chip_select = 0
struct bfin5xx_spi_chip
.cs_gpio = GPIO_P###
There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer. Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always
>= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
|
|
Remove duplicated #include in arch/x86/kernel/ftrace.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
LKML-Reference: <1238503291-2532-1-git-send-email-weiyi.huang@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Preserve I2C clock settings for the Socrates MPC8544 board.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
|
|
Implementation of I2C Adapter/Algorithm Driver for I2C Bus integrated
in Freescale's i.MX/MXC processors.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This build failure:
| drivers/pci/dmar.c:47: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘dmar_tbl_size’
| drivers/pci/dmar.c:62: warning: ‘struct acpi_dmar_device_scope’ declared inside parameter list
| drivers/pci/dmar.c:62: warning: its scope is only this definition or declaration, which is probably not what you want
Triggers due to this commit:
d0b03bd: x2apic/intr-remap: decouple interrupt remapping from x2apic
Which exposed a pre-existing but dormant fragility of the 'select X86_X2APIC'
it moved around and turned that fragility into a build failure.
Replace it with a proper 'depends on' construct.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
LKML-Reference: <1239084280.22733.404.camel@macbook.infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Remove dupilicated #include in arch/x86/kernel/cpu/cpufreq/longhaul.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops. We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.
This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
[paulus@samba.org: changed to use syscall numbers 320 and 321 since
perf_counters is currently using 319.]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
