Age | Commit message (Collapse) | Author |
|
Add function
int gta02_get_pcb_revision(void)
which returns state of GTA02 PCB revision pins. It is also called
and logged during boot with KERN_INFO. The results look like:
b9 b8 b2 b1 b0
GPD4 GPD3 GPD0 GPC15 GPC13
GTA02 A5 and before: 0x000
GTA02 A6 : 0x001
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
We used to drive output high into GPS unit in suspend
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Add platform stuff to deal with going in and out of suspend
so the motion sensor IO is not driving high into unpowered sensors
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Unless I really really missed the point, there is no support for enabling
USB Host power for USB host mode. This patch adds a /sys node for GTA02
that allows control of the charge pump for 5V out on the USB mini connector
It doesn't change any logical mode in the CPU, just enables (1) and disables
(0) USB host power.
# cat /sys/devices/platform/neo1973-pm-host.0/hostmode
0
# echo 1 > /sys/devices/platform/neo1973-pm-host.0/hostmode
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
|
|
|
|
Add support for GPA[] GPIO bus since we have some NCs
but they seem to output-only IO cells so no matter
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
These are initialized already
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
|
|
|
|
|
|
|
|
On GTA02 we use FIQ to manage the vibrator IO now. That
is necessary because we stole timer3 from doing hw pwm
for vibrator. This keeps the same UI in /sys but does
"bitbang pwm" on the same vibrator GPIO
From: Andy Green <andy@openmoko.com>
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
This makes the FIQ stuff specific to one of the timers on the
s3c244x and adds the platform stuff for fiq in the gta02 init
Currently one sysfs node is exposed, a count of FIQ events
cat /sys/devices/platform/sc32440_fiq.0/fiq/count
From: Andy Green <andy@openmoko.com>
Signed-off-by: Andy Green <andy@openmoko.com>
|
|
Adds a C-based FIQ ISR which is very convenient (and unusual --
normally you have to do FIQ ISR in assembler only).
Based on my article:
http://warmcat.com/_wp/2007/09/17/at91rm9200-fiq-faq-and-simple-example-code-patch/
Implemented as a platform device and driver.
Suspend / resume is tested and works.
Signed-off-by: Andy Green <andy@warmcat.com>
|
|
|
|
Modify GTA02 power manager for bluetooth.
1. Default power value isn't correct. Now we set pcf50633 LDO4 to 3.2 voltage.
2. Separate GTA01 and GTA02 source code.
3. Add pcf50633 API for enable register.
|
|
|
|
This is a Linux driver for the STmicro LIS302DL 3-axis accelerometer.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
|
|
|
|
Add the Samsung S3C2442B CPU idcode to the samsung s3c24xx platform code
and fix a Kconfig typo related tot the 2442.
|
|
|
|
This is a MMC/SD driver for the Samsung S3C24xx SD/MMC controller, originally
developed years ago by Thomas Kleffel <tk@maintech.de>.
Due to time restraints, he had no time to further maintain the driver and
follow the mainline Linux changes in the SD/MMC stack.
With his authorization, I have taken over the task of making it compliant to
the current mainline SD/MMC API and take care of the mainline kernel merge.
After a potential kernel inclusion, we would co-maintain the driver.
Acked-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Harald Welte <laforge@gnumonks.org>
|
|
|
|
|
|
This patch adds a PWM api abstraction for the S3C2410 SoC
Signed-off-by: Javi Roman <javiroman@kernel-labs.org>
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
[PATCH] Neo1973 GPS / GSM / Bluetooth power control via sysfs
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
This driver adds support for the SPI-based control interface of the LCM (LCD
Panel) found on the FIC GTA01 hardware.
The specific panel in this hardware is a TPO TD028TTEC1, but the driver should
be able to drive any other diplay based on the JBT6K74-AS controller ASIC.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
This patch adds support for the FIC Neo1973 GTA01 machine type to the ARM port
of the Linux kernel.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
[PATCH] Add Kconfig option to enable NAND bad-block-table support for s3c2410
This patch adds a new CONFIG_MTD_NAND_S3C2410_BBT which, if enabled,
asks the mtd NAND core to use a bad-block table.
Signed-off-by: Harald Welte <laforge@openmoko.org>
|
|
The initialization of clocks uses mutexes, but we execute the resume in
an interrupt context. We therefore have to hand this task to a non-interrupt.
Adapted from a patch by Andy Green.
|
|
Since 2.6.23 kbuild produces a 3GB arch/arm/boot/Image because it includes a
.note.gnu.build-id section at address 0 which is followed by 3GB of 0x00.
The --build-id option is set in the toplevel Makefile.
This patch explicitly puts the notes section after the TEXT section.
|
|
Add support for the LCD 48WVGA module attached to the
SMDK6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add a standard helper to configure the LCD output pins for a 24BPP
display with VSYNC/HSYNC/VDEN.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add a device definition for the new S3C framebuffer
driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Provide the initial register definitions for the newer
style of framebuffer cores found in the Samsung SoCs
such as S3C2450, S3C64XX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into rmk-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: optimize sched_clock() a bit
sched: improve sched_clock() performance
|
|
sched_clock() uses cycles_2_ns() needlessly - which is an irq-disabling
variant of __cycles_2_ns().
Most of the time sched_clock() is called with irqs disabled already.
The few places that call it with irqs enabled need to be updated.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
in scheduler-intense workloads native_read_tsc() overhead accounts for
20% of the system overhead:
659567 system_call 41222.9375
686796 schedule 435.7843
718382 __switch_to 665.1685
823875 switch_mm 4526.7857
1883122 native_read_tsc 55385.9412
9761990 total 2.8468
this is large part due to the rdtsc_barrier() that is done before
and after reading the TSC.
But sched_clock() is not a precise clock in the GTOD sense, using such
barriers is completely pointless. So remove the barriers and only use
them in vget_cycles().
This improves lat_ctx performance by about 5%.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile into x86/urgent
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Reserve elfcorehdr memory in CONFIG_CRASH_DUMP
[IA64] fix boot panic caused by offline CPUs
[IA64] reorder Kconfig options to match x86
[IA64] Build VT-D iommu support into generic kernel
[IA64] remove dead BIO_VMERGE_BOUNDARY definition
[IA64] remove duplicated #include from pci-dma.c
[IA64] use common header for software IO/TLB
[IA64] fix the difference between node_mem_map and node_start_pfn
[IA64] Add error_recovery_info field to SAL section header
[IA64] Add UV watchlist support.
[IA64] Simplify SGI uv vs. sn2 driver issues
|
|
IA64 kdump kernel failed to initialize /proc/vmcore in 2.6.28-rc2.
A bug was introduced in this patch commit:
d9a9855d0b06ca6d6cc92596fedcc03f8512e062
always reserve elfcore header memory in crash kernel
The problem was that the call to reserve_elfcorehdr() should be placed
in CONFIG_CRASH_DUMP rather than in CONFIG_CRASH_KERNEL, which does
not exist.
Signed-off-by: Jay Lan <jlan@sgi.com>
Acked-by: Simon Hormon <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, xen: fix use of pgd_page now that it really does return a page
|
|
Fix the counter overflow check for CPUs with counter width > 32
I had a similar change in a different patch that I didn't submit
and I didn't notice the problem earlier because it was always
tested together.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
|
|
Xen requires that all mappings of pagetable pages are read-only, so
that they can't be updated illegally. As a result, if a page is being
turned into a pagetable page, we need to make sure all its mappings
are RO.
If the page had been used for ioremap or vmalloc, it may still have
left over mappings as a result of not having been lazily unmapped.
This change makes sure we explicitly mop them all up before pinning
the page.
Unlike aliases created by kmap, the there can be vmalloc aliases even
for non-high pages, so we must do the flush unconditionally.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Linux Memory Management List <linux-mm@kvack.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "x86: default to reboot via ACPI"
x86: align DirectMap in /proc/meminfo
AMD IOMMU: fix lazy IO/TLB flushing in unmap path
x86: add smp_mb() before sending INVALIDATE_TLB_VECTOR
x86: remove VISWS and PARAVIRT around NR_IRQS puzzle
x86: mention ACPI in top-level Kconfig menu
x86: size NR_IRQS on 32-bit systems the same way as 64-bit
x86: don't allow nr_irqs > NR_IRQS
x86/docs: remove noirqbalance param docs
x86: don't use tsc_khz to calculate lpj if notsc is passed
x86, voyager: fix smp_intr_init() compile breakage
AMD IOMMU: fix detection of NP capable IOMMUs
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] xsc3: fix xsc3_l2_inv_range
[ARM] mm: fix page table initialization
[ARM] fix naming of MODULE_START / MODULE_END
ARM: OMAP: Fix define for twl4030 irqs
ARM: OMAP: Fix get_irqnr_and_base to clear spurious interrupt bits
ARM: OMAP: Fix debugfs_create_*'s error checking method for arm/plat-omap
ARM: OMAP: Fix compiler warnings in gpmc.c
[ARM] fix VFP+softfloat binaries
|