| Age | Commit message (Collapse) | Author |
|---|
|
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
local_irq_restore -> raw_local_irq_restore -> irq_restore_epilog ->
smtc_ipi_replay -> smtc_ipi_dq -> spin_unlock_irqrestore ->
_spin_unlock_irqrestore -> local_irq_restore
The recursion does abort when there is no more IPI queued for a CPU, so
this isn't usually fatal which is why we got away with this for so long
until this was discovered by code inspection.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Mark Mason <mason@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Original patch posted by Deepak Saxena <dsaxena@plexity.net>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Make smtc_setup_irq() update the list of interrupts which need to be
watched by the debug code itself. Also there is no need to initialize the
IPI swint when running with a single VPE, so don't initialize it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Between the mtc0 or di instruction that disables interrupts and the
following hazard barrier a processor may still take interrupts. If an
interrupt is taken after interrupts are disabled but before the state
is updated it will appear to restore_all that it is incorrectly returning
with interrupts disabled.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Check the IEP bit for R3000 style processors when checking to see if
interrupts will be reenabled in restore_all.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
So until MIPS_MT_SMTC_INSTANT_REPLAY has been rewritten to solve this
issue, don't allow selecting it with PREEMPT.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
arch/mips/pci/pci-ev64120.c:10: warning: implicit declaration of function 'allocate_irqno'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove unused variable.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Typo/thinko in bba6f6fc68e74d4572028646f61dd3505a68747e
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Skip clock calibration if cpu being brought online is exactly the same
speed, stepping, etc., as the previous cpu. This significantly reduces
the time to boot very large systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
ia64 expects following vm layout:
== low memory
[register-stack grows up]
[memory-stack grows down]
== high memory
But the code assigns the base of the register stack at the
maximum stack size offset from the fixed address where the
stack *might* start. Stack randomization will result in the
memory stack starting at a lower address than this, and if the
user has set a low stack limit with "ulimit -s", then you can
end up with the register stack above the memory stack (or if
you were very unlucky right on top of it!).
Fix: Calculate the base address for the register stack starting
from the actual address of the memory stack.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The following 'if' statement in ia64_setup_msi_irq() always fails even
if create_irq() returns <0 value, because variable 'irq' is defined as
unsigned int. It would cause invalid memory access.
irq = create_irq();
if (irq < 0)
return irq;
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Add support for the MPC8323E Reference Development Board (RDB). The board
is a mini-ITX reference board with 64M DDR2, 16M flash, USB, PCI,
10/100 ethernet, serial, and phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Correct the alignment of the internal buffer used by the QUICC Engine
SDMA controller to 4Kbytes. Correct the shift direction in the logic
that sets up the SDMR register for the QUICC Engine SDMA controller.
Signed-off-by: Chuck Meade <chuckmeade@mindspring.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This adds support of suspend/resume on i386 for HPET, which fixes a
number of timer-related failures around STR.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a few miscellaneous compilation problems -
an assignment with mismatched types in ldt.c
a missing include in mconsole.h which needs a definition of uml_pt_regs
I missed removing an include of user_util.h in hostfs
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Permit lvm to create logical volumes without crashing UML.
When device-mapper's DM_DEV_CREATE_CMD ioctl is called to create a new device,
dev_create()->dm_create()->alloc_dev()-> blk_queue_bounce_limit(md->queue,
BLK_BOUNCE_ANY) is called.
blk_queue_bounce_limit(BLK_BOUNCE_ANY) calls init_emergency_isa_pool() if
blk_max_pfn < blk_max_low_pfn. This is the case on UML, but
init_emergency_isa_pool() hits BUG_ON(!isa_page_pool) because there doesn't
seem to be a dma zone on UML for mempool_create() to allocate from.
Most architectures seem to have max_low_pfn == max_pfn, but UML doesn't
because of the uml_reserved chunk it keeps for itself. From what I can see,
max_pfn and max_low_pfn don't get much use after the bootmem-allocator stops
being used anyway, except that they initialize the block layer's
blk_max_low_pfn/blk_max_pfn.
This ensures init_emergency_isa_pool() doesn't crash uml in this situation by
setting max_low_pfn == max_pfn in mem_init().
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As the comment immediately preceding this points out, this list is changed in
irq context, so it needs to be protected with spin_lock_irqsave in process
context when it is processed.
Sometimes, gcc should just compile the comments and forget the code.
The IRQ side of this was better, in the sense that it blocked and unblocked
interrupts, but it still should have saved and restored them.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a NULL dereference when unplugging a device. The default value of
err_msg wants to be "" in case the driver doesn't modify it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 62f96cb01e8de7a5daee472e540f726db2801499 introduced per-devices
queues and locks, which was fine as far as it went, but left in place a
global which controlled access to submitting requests to the host. This
should have been made per-device as well, since it causes I/O hangs when
multiple block devices are in use.
This patch fixes that by replacing the global with an activity flag in the
device structure in order to tell whether the queue is currently being run.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the NAND flash timings on the AT91SAM9260.
The current timings lead to the detection of a number of bad blocks.
These timings are now set the same as on the AT91SAM9263.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix a bug in dcr_unmap().
At unmap time the DCR offset need to be added instead of substracted.
Signed-off-by: Jean-Christophe Dubois <jdubois@mc.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[VIDEO]: Fix section mismatch in cg3.c
[SPARC]: sparc64 gcc-4.2.0 20070317 -Werror failure
[VIDEO] ffb: Fix two DAC handling bugs.
[SPARC32]: Fix SMP build regression
[DRM]: Delete sparc64 FFB driver code that never gets built.
|
|
So I think the right solution is to simply make pci_enable_device just
flip enable bits and move the rest of the work someplace else.
However a thorough cleanup is a little extreme for this point in the
release cycle, so I think a quick hack that makes the code not stomp the
irq when msi irq's are enabled should be the first fix. Then we can
later make the code not change the irqs at all.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__sdivsi3_i4i, __udiv_qrnnd_16, and __udivsi3_i4i don't exist
outside of the ST compiler, so kill them off.
This causes compile failures with other GCC4 compilers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This reverts commit 94985134b7b46848267ed6b734320db01c974e72 and
insteads removes the WARN_ON() that caused that commit in the first
place.
The problem is that we call disable_nonboot_cpus() in swsusp before
powering down the system in order to avoid triggering the WARN_ON()
in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping() and this doesn't
work well on Thomas' system.
So instead, remove the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:
init_low_mapping(), which triggers every time during the suspend to disk
in the platform mode, as the potential problem it is related to doesn't
seem to occur in practice.
[ I think we might want to disallow the case of multiple users of that
mm, or something. Normally, playing with the current process page
tables on the current CPU should be fine as long as we don't have
other threads using those tables at the same time..
Anyway, not pretty, but better than the warning or the lockup - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The clockevents / tick management code expects an error value, when the
event is already expired. hpet_next_event() returns 1 in that case.
Fix it to return the proper -ETIME error code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch uses MAX_REG_NR consistently to refer to the register file size.
FRAME_SIZE isn't sufficient because on x86_64, it is smaller than the
ptrace register file size. MAX_REG_NR was introduced as a consistent way
to get the number of registers, but wasn't used everywhere it should be.
When this causes a problem, it makes PTRACE_SETREGS fail on x86_64 because
of a corrupted segment register value in the known-good register file. The
patch also adds a register dump at that point in case there are any future
problems here.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit b19cbe2a1695c09c74f83646c4b82b51123b3690 [BRIDGE]: Fix fdb RCU
race
breaks sparc SMP build because atomic_add_unless is not exported.
This patch exports atomic_add_unless and atomic_cmpxchg.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mpc832x_mds.h was exporting a function that didn't exist anymore. Once removed
the header had no purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In two places, ucc_slow_init() passes a physical address instead of the
virtual address to functions that were expecting the latter, causing a kernel
panic. us_info->regs contains the physical address of the UCC register set.
The registers are ioremap'd to kernel space, and the virtual pointers are
stored in us_regs. The code was using us_info->regs when it should have been
using us_regs.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Delete apparently unused header file
arch/powerpc/platforms/83xx/mpc834x_itx.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected. Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled. A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Unify PCI Express memory map registers structure define
to arch/pwoerpc/sysdev/fsl_pcie.h for Freescale 85xx/86xx
processor family.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This move sets the stage for the use of generic PCI Express
code in 85xx and 86xx parts from FSL. Subsequent patches
for 8548 and 8544 will be able to use this shared code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: Fix ap_poll_requests counter in lost requests error path.
[S390] zcrypt: Fix possible dead lock in AP bus module.
[S390] cio: Device status validity.
[S390] kprobes: Align probe address.
[S390] Fix TCP/UDP pseudo header checksum computation.
[S390] dasd: Work around gcc bug.
|
|
This patch automatically enables pci=bfsort for the Dell PowerEdge
R900. This is necessary to ensure the onboard NICs enumerate in the
proper order, similar to the other systems already on the list.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Running a probe on s390 with a probe address that is not 4 byte aligned
results in a Kernel BUG. The problem is that the stura instruction used
by swap_instruction requires the destination address to be 4 byte aligned.
As stura only writes 4 bytes, aligning to the next 4 byte aligned address
results in the breakpoint instruction being stored past the probe address.
The fix is to align the address backward (to the previous 4 byte aligned
address) and writing the two byte breakpoint instruction in the appropriate
bytes.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
This patch adds a reg.h to the zImage code, with common definitions
for accessing system registers. For now, this includes functions for
retrieving the PVR and the stack pointer. This patch then uses the
new reg.h to let start() display the running stack address without
having to explicitly pass the stack as a parameter from the asm code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch adds the correct attributes to the zImage's versions of
printf to make gcc generate format string mismatch warnings. It also
corrects several minor problems with format strings in the zImage thus
discovered.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Before the plethora of platforms gets any worse, establish a common
rule to invoke the wrapper for any platform. Add arguments to
the rule for initrd, dts, dtb, etc. Show example usage with initrd.
Create default rules for zImage, and zImage.initrd. initrd targets
depend on the ramdisk file.
Don't consider targets for zImage.initrd that are targets for zImage.
This means uImage is no longer considered a target for zImage.initrd.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Now that obj-boot is in targets, we can remove (twice) it from clean-files.
zImage.initrd was missing, move zImage nearer where its used, and place
zImage.initrd next to it. Remove non-ported zImage.sandpoint, and add
auto-generation of unconfigured zImage.initrd* like image-.
Signed-off-by: Milton Miller <miltonm@bga.com>
--
Testing: did a few builds and cleans
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Kbuild if_changed and if_changed_dep require the use of the dummy
FORCE to get the dependencies right. Also add to targets to get
correct behavior.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Some platforms might need to run some code before the zImage start, but
could otherwise use the bss clear and relocation code. Export the
start address strongly as zImage_start_lib.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
