| Age | Commit message (Collapse) | Author |
|---|
|
WARNING: vmlinux.o(.text+0x27032): Section mismatch in reference from the function get_tce_space_from_tar() to the function .init.text:calgary_bus_has_devices()
The function get_tce_space_from_tar() references
the function __init calgary_bus_has_devices().
This is often because get_tce_space_from_tar lacks a __init
annotation or the annotation of calgary_bus_has_devices is wrong.
get_tce_space_from_tar is called only from __init function (calgary_init)
and calls __init function (calgary_bus_has_devices).
So annotate it properly.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Chandru Siddalingappa <chandru@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Take out part of get_local_pda referencing __init function (free_bootmem)
to new (static) function marked as __ref. It's safe to do because free_bootmem
is called before __init sections are dropped.
WARNING: vmlinux.o(.cpuinit.text+0x3cd7): Section mismatch in reference from the function get_local_pda() to the function .init.text:free_bootmem()
The function __cpuinit get_local_pda() references
a function __init free_bootmem().
If free_bootmem is only used by get_local_pda then
annotate free_bootmem with a matching annotation.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
arch/x86/power/cpu_32.c __save_processor_state calls read_cr4()
only a i486 CPU doesn't have the CR4 register. Trying to read it
produces an invalid opcode oops during suspend to disk.
Use the safe rc4 reading op instead. If the value to be written is
zero the write is skipped.
arch/x86/power/hibernate_asm_32.S
done: swapped the use of %eax and %ecx to use jecxz for
the zero test and jump over store to %cr4.
restore_image: s/%ecx/%eax/ to be consistent with done:
In addition to __save_processor_state, acpi_save_state_mem,
efi_call_phys_prelog, and efi_call_phys_epilog had checks added
(acpi restore was in assembly and already had a check for
non-zero). There were other reads and writes of CR4, but MCE and
virtualization shouldn't be executed on a i486 anyway.
Signed-off-by: David Fries <david@fries.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
WARNING: vmlinux.o(.text+0x118f7): Section mismatch in reference from the function construct_ioapic_table() to the function .init.text:MP_bus_info()
The function construct_ioapic_table() references
the function __init MP_bus_info().
This is often because construct_ioapic_table lacks a __init
annotation or the annotation of MP_bus_info is wrong.
construct_ioapic_table is called only from construct_default_ISA_mptable which is __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1591): Section mismatch in reference from the function init_amd() to the function .init.text:check_enable_amd_mmconf_dmi()
The function __cpuinit init_amd() references
a function __init check_enable_amd_mmconf_dmi().
If check_enable_amd_mmconf_dmi is only used by init_amd then
annotate check_enable_amd_mmconf_dmi with a matching annotation.
check_enable_amd_mmconf_dmi is only called from init_amd which is __cpuinit
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1fe7): Section mismatch in reference from the function MP_processor_info() to the variable .init.data:x86_quirks
The function __cpuinit MP_processor_info() references
a variable __initdata x86_quirks.
If x86_quirks is only used by MP_processor_info then
annotate x86_quirks with a matching annotation.
MP_processor_info uses x86_quirks which is __init and is used only from
smp_read_mpc and construct_default_ISA_mptable which are __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
WARNING: vmlinux.o(.text+0x7950): Section mismatch in reference from the function native_calibrate_tsc() to the function .init.text:tsc_read_refs()
The function native_calibrate_tsc() references
the function __init tsc_read_refs().
This is often because native_calibrate_tsc lacks a __init
annotation or the annotation of tsc_read_refs is wrong.
tsc_read_refs is called from native_calibrate_tsc which is not __init
and native_calibrate_tsc cannot be marked __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
WARNING: vmlinux.o(.text+0x17a3e): Section mismatch in reference from the function set_pte_vaddr_pud() to the function .init.text:spp_getpage()
The function set_pte_vaddr_pud() references
the function __init spp_getpage().
This is often because set_pte_vaddr_pud lacks a __init
annotation or the annotation of spp_getpage is wrong.
spp_getpage is called from __init (__init_extra_mapping) and
non __init (set_pte_vaddr_pud) functions, so it can't be __init.
Unfortunately it calls alloc_bootmem_pages which is __init,
but does it only when bootmem allocator is available (after_bootmem == 0).
So annotate it accordingly.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
|
|
write.
By writing directly, a memory access violation can occur whilst
hotplugging a CPU if the entry was previously marked read-only.
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
Plus add a build time check so this doesn't go unnoticed again.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Adds a simple IRQ autodetection to the AMD Geode MFGPT driver, and more
importantly, adds some checks, if IRQs can actually be received on the
chosen line. This fixes cases where MFGPT is selected as clocksource
though not producing any ticks, so the kernel simply starves during
boot.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Cc: Andres Salomon <dilinger@debian.org>
Cc: linux-geode@bombadil.infradead.org
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
fix:
arch/x86/kernel/acpi/sleep.c:24: warning: 'temp_stack' defined but not used
[ Sven Wegener <sven.wegener@stealer.net>: fix build bug ]
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
clean up the failure message - and redirect people to bugzilla
instead of lkml.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
> it just won't work at boot time - the second logic unit will be stuck:
>
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 5586.12 BogoMIPS (lpj=2793063)
> CPU: Trace cache: 12K uops, L1 D cache: 16K
> CPU: L2 cache: 1024K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> CPU1: Thermal monitoring enabled (TM1)
> Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
> Brought up 2 CPUs
> testing NMI watchdog ... <4>WARNING: CPU#1: NMI appears to be stuck (0->0)!
while at it... - fix that newline
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: jvillalo@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Do we actually want these DirectMap lines in the x86 /proc/meminfo?
I can see they're interesting to CPA developers and TLB optimizers,
but they don't fit its usual "where has all my memory gone?" usage.
If they are to stay, here are some fixes.
1. On x86_32 without PAE, they're not 2M but 4M pages: no need to
mess with the internal enum, but show the right name to users.
2. Many machines can never show anything but 0 for DirectMap1G,
so suppress that line unless direct_gbpages are really enabled.
3. The unit in /proc/meminfo is kB not number of pages: HugePages
messed that up, but they're an example to regret not to follow.
4. Once we use kB, it's easy to see that 1GB has gone missing (which
explains why CONFIG_CPA_DEBUG=y soon wraps DirectMap2M negative):
because head_64.S's level2_ident_pgt entries were not counted.
My fix is not ideal, but works for more and for less than 1G,
and avoids interfering with early bootup pagetable contortions.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Adjust experimental tags in Kconfig, update config to notice that
i386/x86_64 is now single architecture.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When a CPU core is shut down, all of its caches need to be flushed
to prevent stale data from causing errors if the core is resumed.
Current Linux suspend code performs an assignment after the flush,
which can add dirty data back to the cache. On some AMD platforms,
additional speculative reads have caused crashes on resume because
of this dirty data.
Relocate the cache flush to be the very last thing done before
halting. Tie into an assembly line so the compile will not
reorder it. Add some documentation explaining what is going
on and why we're doing this.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Acked-by: Mark Borden <mark.borden@amd.com>
Acked-by: Michael Hohmuth <michael.hohmuth@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Currently, setup_p4_watchdog() use CCCR_OVF_PMI1 to enable the counter
overflow interrupts to the second logical core. But this bit doesn't work
on Pentium 4 Ds (model 4, stepping 4) and this patch avoids its use on
these processors. Tested on 4 different machines that have this
specific model with success.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Cc: jvillalovos@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
If sysfs registration fails all memory used by IOMMU is freed. This
happens after dma_ops initialization and the functions will access the
freed memory then.
Fix this by initializing dma_ops after the sysfs registration.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch adds device table initializations which forbids memory accesses
for devices per default and disables all page faults.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
There's so much broken mmconfig hardware/bios'es out there,
that classing this as an error seems a little extreme.
Lower its priority to KERN_INFO so that it isn't so noisy
when booting with 'quiet'
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
msr_open tests for someone trying to open a device for a nonexistent CPU.
However, the function always returns 0, not ret like it should, hence
userspace can BUG the kernel trivially. This bug was introduced by the
cdev lock_kernel pushdown patch last May.
The BUG can be reproduced with these commands:
# mknod fubar c 202 8 <-- pick a number less than NR_CPUS that is not
the number of an online CPU
# cat fubar
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
AMD SB700 based systems with spread spectrum enabled use a SMM based
HPET emulation to provide proper frequency setting. The SMM code is
initialized with the first HPET register access and takes some time to
complete. During this time the config register reads 0xffffffff. We
check for max. 1000 loops whether the config register reads a non
0xffffffff value to make sure that HPET is up and running before we go
further. A counting loop is safe, as the HPET access takes thousands
of CPU cycles. On non SB700 based machines this check is only done
once and has no side effects.
Based on a quirk patch from: crane cai <crane.cai@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
clear bits for cpu nr > 8.
This allows us to boot the full range of possible CPUs that the
supported APIC model will allow. Previously we'd hang or boot up
with less than 8 CPUs.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
so we don't get warning on 32bit system with 64g RAM or more
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
For some reason we had two parsers registered for maxcpus=. One in init/main.c
and another in arch/x86/smpboot.c. So I nuked the one in arch/x86.
Also 64-bit kernels used to handle maxcpus= as documented in
Documentation/cpu-hotplug.txt. CPUs with 'id > maxcpus' are initialized
but not booted. 32-bit version for some reason ignored them even though
all the infrastructure for booting them later is there.
In the current mainline both 64 and 32 bit versions are broken.
This patch restores the correct behaviour. I've tested x86_64 version on
4- and 8- way Core2 and 2-way Opteron based machines. Various config
combinations SMP, !SMP, CPU_HOTPLUG, !CPU_HOTPLUG.
Booted with maxcpus=1 and maxcpus=4, etc. Everything is working as expected.
So far we've received two reports from different people confirming that 32-bit
version also works fine, both on dual core laptops and 16way server machines.
[v2: This version fixes visws breakage pointed out by Ingo.]
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com>
Cc: lizf@cn.fujitsu.com
Cc: jeff.chua.linux@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
usb: musb: pass configuration specifics via pdata
usb: musb: fix hanging when rmmod gadget driver
USB: Add MUSB and TUSB support
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
USB: Add vendor/product id of ZTE MF628 to option
USB: quirk PLL power down mode
USB: omap_udc: fix compilation with debug enabled
usb: cdc-acm: drain writes on close
usb: cdc-acm: stop dropping tx buffers
usb: cdc-acm: bugfix release()
usb gadget: issue notifications from ACM function
usb gadget: remove needless struct members
USB: sh: r8a66597-hcd: fix disconnect regression
USB: isp1301: fix compilation
USB: fix compiler warning fix
usb-storage: unusual_devs entry for Nokia 5300
USB: cdc-acm.c: Fix compile warnings
USB: BandRich BandLuxe C150/C250 HSPA Data Card Driver
USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
usb: isp1760: don't be noisy about short packets.
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
|
|
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Things like lockdep can try to do stack backtraces before
the irqstack blocks have been setup. So don't try to match
their ranges so early on.
Also, remove unused variable in save_stack_trace().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up the code for crashes during SpeedStep probing on older
machines.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Done as a script (well, a single "git mv" actually) on request from
Yoshinori Sato as a way to avoid a huge diff.
Requested-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use WARN() instead of a printk+WARN_ON() pair; this way the message becomes
part of the warning section for better reporting/collection.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
SGI UV will have MMCFG base addresses that are greater than 4GB (32 bits).
v2: Use CONFIG_RESOURCES_64BIT instead of CONFIG_X86_64.
v3: Create a flag, that is set by platform specific code,
to disable the > 4GB check.
Signed-off-by: John Keller <jpk@sgi.com>
Cc: jpk@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
WARNING: vmlinux.o(.text+0xcd1f): Section mismatch in reference from the function find_and_reserve_crashkernel() to the function .init.text:find_e820_area()
The function find_and_reserve_crashkernel() references
the function __init find_e820_area().
This is often because find_and_reserve_crashkernel lacks a __init
annotation or the annotation of find_e820_area is wrong.
WARNING: vmlinux.o(.text+0xcd38): Section mismatch in reference from the function find_and_reserve_crashkernel() to the function .init.text:reserve_bootmem_generic()
The function find_and_reserve_crashkernel() references
the function __init reserve_bootmem_generic().
This is often because find_and_reserve_crashkernel lacks a __init
annotation or the annotation of reserve_bootmem_generic is wrong.
find_and_reserve_crashkernel is called from __init function (reserve_crashkernel)
and calls 2 __init functions (find_e820_area, reserve_bootmem_generic),
so mark it __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
WARNING: vmlinux.o(.text+0x14cf8): Section mismatch in reference from the function map_high() to the function .init.text:init_extra_mapping_uc()
The function map_high() references
the function __init init_extra_mapping_uc().
This is often because map_high lacks a __init
annotation or the annotation of init_extra_mapping_uc is wrong.
WARNING: vmlinux.o(.text+0x14d05): Section mismatch in reference from the function map_high() to the function .init.text:init_extra_mapping_wb()
The function map_high() references
the function __init init_extra_mapping_wb().
This is often because map_high lacks a __init
annotation or the annotation of init_extra_mapping_wb is wrong.
map_high is called only from __init functions (map_*_high)
and calls 2 __init_functions (init_extra_mapping_*)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
yesterday I tried to reactivate my old 486 box and wanted to install a
current Linux with latest kernel on it. But it turned out that the
latest kernel does not boot because the machine crashes early in the
setup code.
After some debugging it turned out that the problem is the query_ist()
function. If this interrupt with that function is called the machine
simply locks up. It looks like a BIOS bug. Looking for a workaround for
this problem I wrote the attached patch. It checks for the CPUID
instruction and if it is not implemented it does not call the speedstep
BIOS function. As far as I know speedstep should be available since some
Pentium earliest.
Alan Cox observed that it's available since the Pentium II, so cpuid
levels 4 and 5 can be excluded altogether.
H. Peter Anvin cleaned up the code some more:
> Right in concept, but I dislike the implementation (duplication of the
> CPU detect code we already have). Could you try this patch and see if
> it works for you?
which, with a small modification to fix a build error with it the
resulting kernel boots on my machine.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that all the direct includes of asm/of_device.h are gone, this is
safe to do.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] use bcd2bin/bin2bcd
[IA64] Ensure cpu0 can access per-cpu variables in early boot code
|
|
WARNING: vmlinux.o(.text+0x2fdf): Section mismatch in reference from the variable .LM3 to the variable .init.text:___alloc_bootmem
The function .LM3() references
the variable __init ___alloc_bootmem.
This is often because .LM3 lacks a __init
annotation or the annotation of ___alloc_bootmem is wrong.
WARNING: vmlinux.o(.text+0x2ff5): Section mismatch in reference from the variable .LM4 to the variable .init.text:___alloc_bootmem
The function .LM4() references
the variable __init ___alloc_bootmem.
This is often because .LM4 lacks a __init
annotation or the annotation of ___alloc_bootmem is wrong.
WARNING: vmlinux.o(.text+0x300b): Section mismatch in reference from the variable .LM5 to the variable .init.text:___alloc_bootmem
The function .LM5() references
the variable __init ___alloc_bootmem.
This is often because .LM5 lacks a __init
annotation or the annotation of ___alloc_bootmem is wrong.
WARNING: vmlinux.o(.text+0x304b): Section mismatch in reference from the variable .LM10 to the variable .init.text:_free_area_init
The function .LM10() references
the variable __init _free_area_init.
This is often because .LM10 lacks a __init
annotation or the annotation of _free_area_init is wrong.
WARNING: vmlinux.o(.text+0x30a3): Section mismatch in reference from the variable .LM17 to the variable .init.text:_free_all_bootmem
The function .LM17() references
the variable __init _free_all_bootmem.
This is often because .LM17 lacks a __init
annotation or the annotation of _free_all_bootmem is wrong.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch changes ia64 to use the new bcd2bin/bin2bcd functions instead
of the obsolete BCD2BIN/BIN2BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
ia64 handles per-cpu variables a litle differently from other architectures
in that it maps the physical memory allocated for each cpu at a constant
virtual address (0xffffffffffff0000). This mapping is not enabled until
the architecture specific cpu_init() function is run, which causes problems
since some generic code is run before this point. In particular when
CONFIG_PRINTK_TIME is enabled, the boot cpu will trap on the access to
per-cpu memory at the first printk() call so the boot will fail without
the kernel printing anything to the console.
Fix this by allocating percpu memory for cpu0 in the kernel data section
and doing all initialization to enable percpu access in head.S before
calling any generic code.
Other cpus must take care not to access per-cpu variables too early, but
their code path from start_secondary() to cpu_init() is all in arch/ia64
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
fix spinlock recursion in hvc_console
stop_machine: remove unused variable
modules: extend initcall_debug functionality to the module loader
export virtio_rng.h
lguest: use get_user_pages_fast() instead of get_user_pages()
mm: Make generic weak get_user_pages_fast and EXPORT_GPL it
lguest: don't set MAC address for guest unless specified
|
